When buying a used car from a private party or auto auction, this is frequently the case. As many SRS components are one-time use only, if the car was previously in an accident and the airbags deployed, there’s a risk the problem wasn’t addressed properly. It might be a seat belt tensioner, crash sensor, or clock spring, among other things.
The car’s ECM needs to be reprogrammed in order to essentially reset the airbag system, even if all the parts were replaced. The airbag light will continue to flash if this reset has not yet taken place.
In This Article...
The airbag blinking light on my 2013 Nissan Rogue won’t go out (reset).
I repeatedly attempted the following procedure (found on a few websites), but it was unsuccessful.
1. Start by turning the key from off to on.
2. Keep a watchful eye on the airbag light. It will remain on for a short while. switch the key off right away after it stops blinking (at the beginning of the flashing).
3) Count to five (1 Mississippi, 2 Mississippi . . . .)
4. Continue to step 3 twice more to complete the cycle three times.
5. After turning the key, observe the light. It will then begin blinking in a new, slower pattern. In diagnostic mode now. There is no rush; you can watch this for a long.
6. Turn the key off once more, count to five like you did in step 3 again, and then turn it back on. If the process was successful, there would be no flashing of the airbag light.
Here is a video showing the flashing pattern, which is 1 long blink and 12 short blinks: https://youtu.be/uttZSE6g5GM
Repeat the process four more times in total. Key turned on. Attend to the airbag light. As soon as the light goes out, turn the key off. There’s no need to count to five.
Sadly, that doesn’t stop the SRS light from flashing in the same sequence. The passenger air bag light is also on.
In my opinion, counting the blinks is inaccurate; instead, you should bring your Rouge to an auto parts shop and ask them to check the air bag light’s code. If you only wish to clear the code, disconnect the battery from the car for around 30 minutes; if the light returns, there is undoubtedly a problem.
It appears that you have accomplished the majority of your goals. The next step is to connect it to a computer and identify the fault. The airbag sensor was the cause of a similar problem with a 06 Volkswagen we owned.
2009 Nissan Rogue Air Bag Light On Issue
The 2009 Nissan Rogue, along with the 2008 and 2010 Rogue, has a faulty airbag sensor. No matter who ever sits in the passenger seat, the airbag weight sensor in the seat continues to disable the airbag. Additionally, it leaves a dashboard airbag light that is flashing. Nissan is aware of the issue and charges you an hourly rate to diagnose the issue before charging you over $2000 to replace the seat, much like they did for the 2008 and 2010 cars that were subject to a recall. The 2009 model uses the same components.
Step 4
After 5 seconds, repeat step 1 again. Three times should be put into this. At this time, the status light can be blinking in a different way. Just stick to the same easy instructions. Turn the ignition to ON after inserting the key. Blinking should begin after the light has stopped, and the key should be swiftly turned to the OFF position and removed. Repeat this procedure a total of twice.
Re: Flashing airbag light (redroguegal)
A faulty OCS (occupant classification sensor) in the passenger seat has led to a recall for the 2008 Nissan Rogue (2009 models are unaffected). It might be the reason for the airbag warning light that you mention flashing.
I’m grateful. Nissan did not send me a note about this. I guess they didn’t include me on their “list”. I’ll submit it the next day. It’s interesting that when I called the dealer, nobody could help. You’re an expert!
This morning, I contacted the dealer. He informed me that my car was exempt from the recall. I told him it says all 2008 Rogues in the one I read. That wasn’t true, he said, but bring it in the following day. In addition, I warned him that in the event of an accident, nobody should sit in the passenger seat. He claimed there was no issue. geez! Tomorrow, I’ll let you in on the details.
How to Turn Off the SRS Airbag Warning Light on a Nissan Rogue (2008-2020)
Follow these steps if your Nissan Rogue’s SRS Airbag warning light comes on while you’re driving and you wish to clear it or turn it off:
Without starting the engine, turn the ignition switch to the “ON” position.
Press the “Start” button twice without using the brake pedal if your car has a Smart key button.
Keep a watchful eye on the airbag light.
It will remain on for a short while. switch the key off right away after it stops blinking (at the beginning of the flashing).
- more than three seconds to wait
- Once you’ve completed the cycle three times, repeat steps 1-3 two more times.
- Watch the light when you turn the key now. It will then begin blinking in a new, slower pattern.
- Turn the key off once more, wait for at least three further seconds, and then turn it back on.
- To make sure the indication has been reset, turn off the ignition and then start the vehicle.
If the process was successful, there would be no flashing of the airbag light. The Nissan maintenance handbook provides the foundation for this course. It should be followed for all Nissan Rogue models (2008 2009 2010 2011 2012 2013 2014 2015 2016 2017 2018 2019 2020 model years). I hope you found the information in this post on how to reset the Nissan Rogue SRS Airbag Warning Light (2008-2020) useful. Best of luck!
Why is the Nissan Maxima’s airbag light flashing?
If you’ve recently added a radio, new vehicle seats, or other electrical components in your Nissan Maxima, the airbag light might be blinking. Because your automobile believes there is a problem with the airbag deployment system, your airbag light is flashing.
What does the airbag light flashing indicate?
A flashing airbag warning light means there is a serious issue with the SRS system, therefore you should get it fixed right away.
Even while you should still take it to a repairman if the light remains on, there are a few things you may do first that might help.
If there is anything impeding the seatbelt sensor, such as dirt or anything else that may have fallen in there, start by looking at the seatbelt buckle.
If that doesn’t work, check to make sure the seatbelts aren’t tangled or trapped, then try giving them a vigorous tug to tighten them up. This could assist in resetting any tensioning sensor difficulties.
Grab a torch and perform a quick visual inspection under the seats, where the wiring to the seat and seatbelt sensors typically joins, to see if any wires or connectors have fallen loose.
A broken clockspring in the steering wheel is another probable factor. The clockspring serves as an electrical connection between the steering wheel and dashboard for features like the horn, radio and cruise control switches, and the airbag in addition to flicking the steering wheel back to the center after you turn.
The airbag and sensor circuit may momentarily open if the clockspring is somewhat worn, turning on the warning light. In some instances, reestablishing the connection can be done by simply spinning the steering wheel to full lock in each direction while still moving.
You should never inspect the airbag unit or disassemble it since it carries an explosive charge that might kill you.
How can I stop the flashing of my airbag light?
The airbag light connects the seat belt system and the airbag system as part of the Supplement Restraint System (SRS) in automobiles (and vice-versa). When you turn on your automobile, the airbag light comes on for around seven seconds before going out, signifying that the internal system check was successful and finished. When the airbag light either never turns on or stays on while blinking, an issue exists. The airbag light needs to be reset at this stage.
Examining seat belt components, fixing bad clock springs, and replacing faulty sensors are a few techniques for turning off an airbag light. New bulbs or a fully charged battery are other options. While most repairs can be done without a professional, others may.
The following 10 steps will reset your airbag light:
- Turn on and off your ignition.
- Test drive your car when it has been restarted.
- Check the airbag switch for the passenger.
- Check to see if the seat belts are in place and functioning properly.
- Check to see if the passenger seat sensor is off.
- Use a scanner with the ability to reset the SRS or airbag light.
- Fix the broken airbag sensors.
- Replace or repair a broken clock spring.
- Check to see if the airbag is working properly.
- seek for a specialist’s help.
Although not exhaustive, the list above includes tried-and-true methods for tackling the problem. Some of them might not apply to your vehicle because compatibility is always based on the year, make, and model. It is recommended that you have your service manual on hand when carrying out any of these fixes. Always follow the manufacturer’s recommendations, too. Let’s get started on resetting your airbag light right away.
Driving while the airbag light is flashing is it safe?
No, driving while the airbag light is on is not safe. When the airbag light comes on, the vehicle’s airbag system is malfunctioning. Due to this flaw, the airbag is unlikely to deploy after an accident. Therefore, it is not advised that you use the vehicle until the system has been fixed.
Never disregard the important caution. There’s no need to gamble with the car, even though it doesn’t make it unsafe to drive.
The light does, however, show that the SRS parts are not functioning properly. This may potentially indicate that the airbags won’t activate in the event of a collision. You shouldn’t wait until you are involved in an accident to determine whether the airbags will keep you safe.
On a Nissan, how do you reset the airbag?
- Alternately turning the ignition on and off.
- Air Bag warning lamp illuminates for 7 seconds before turning off, and ignition switch is turned OFF 1 second later.
- Wait for more than three seconds after turning off the ignition switch.
- Follow steps 1 through 3 twice.
- Activate the ignition switch.
- The SRS lamp has been turned back on.
Can an airbag light be caused by a low battery?
The backup battery is dead. It is the most frequent cause of an airbag light that won’t go off. It might take place if your car’s battery is running low or has been depleted for any other cause. When the battery is fully recharged, the issue will be resolved.
Can a blown fuse turn on the airbag light?
The car could have blown a fuse, for example. There are other fuses that could be to blame, but fuse #13 is most likely the one. You probably need to change fuse #13 and perhaps other fuses if your airbag light is on and your rear windshield wiper is not working. The airbag light can undoubtedly turn on as a result of blown fuses.
The airbag light may also abruptly turn on in a number of other situations. A mechanic or auto parts store should be able to decipher the code that the airbag system emits when it is acting up, which will give them a hint as to what specific issue the airbag is experiencing. There are numerous potential issues with the airbag because it is a complicated system of sensors, wiring, and programming that must suddenly activate during an accident after lying dormant for years. Check the fuse box to see whether you have a blown fuse first, but if not, you’ll likely need to take it to the dealer or a qualified mechanic for service.