How To Change Brake Light On 2018 Hyundai Elantra?

Get a 2018 Hyundai Elantra GT Brake Light Mini Bulb from AutoZone for your automobiles, trucks, and SUVs.

How can a brake light be changed?

  • Step 1: Open the tailgate or trunk.
  • Step 2: Remove the tail lamp assembly (if needed)
  • Step 3: Remove the bulb.
  • Step 4: Insert a replacement bulb after adding bulb grease.
  • Step 5: Reattach the component (if needed)
  • Repeat on the other side in step 6

What causes a Hyundai Elantra’s brake lights to remain on?

Bad Switch: A faulty or failed switch is a typical cause of the Parking Brake light remaining on. You may quickly verify this by jiggling the handle once it has been lowered. The switch is most likely to be the problem and needs to be replaced if the light goes out (or goes out and comes back on).

If the brake handle is not fully down, there is another factor that could cause the light to remain on. Verify again that the parking brake is released and that the handle is fully lowered. The light will remain on if the parking brake cable is under any stress.

Parking Brake Not Disengaging: Occasionally, the parking brake itself is the source of the issue rather than the switch or the wires. The dash warning light will remain on if the brake does not release when the handle is dropped.

Low Brake Fluid: Your Parking Brake light is a multipurpose device that is intended to turn on when the reservoir’s fluid level falls below a specific level. As the fluid level fluctuates, you might see the light turning on or off when making turns.

The brake fluid level sensor in your master cylinder is malfunctioning. It is sometimes integrated into the reservoir cap, and other times it is positioned on the side of the sensor. The Parking Brake light will come on if the sensor malfunctions or becomes faulty.

Uneven Fluid Pressure: If your automobile has uneven brake fluid pressure in one or more lines, it may influence how well it can stop and may even cause it to pull to one side or the other. The parking brake light in your dash can also be activated by it.

Are brake lights fixed by mechanics?

Numerous distinct flaws may be to blame for your brake lights not working. Brake light issues can have a variety of causes, from one light operating well while the other is burned out to both lights not working. A mechanic can easily and expertly replace the bulb and address any other problems.

What is the time required to replace a brake light?

Get Ready Fortunately, changing the tail light bulbs isn’t hard and shouldn’t take you more than 45 minutes to an hour. Be careful that newer models could be a little trickier to disassemble than older ones because there will be more wires.

AutoZone will they replace brake lights?

AutoZone will they replace brake lights? Although AutoZone doesn’t really provide brake light replacement services, our staff can help you with any inquiries you may have, aid you in locating the necessary supplies to get started, and perhaps even lend a hand.

What distinguishes a brake light from a tail light?

There are multiple lights in tail lights, each with a distinct function. When you apply the brakes to slow down, brake lights on your taillight let other cars know. To improve visibility for drivers behind you during the night or inclement weather, the tail lights come on when the headlights are turned on.

Have all automobiles two brake lights?

These may seem simple, but they are crucial for alerting drivers who are behind you as you brake. You are required to have two operational brake lights. The fact that they are mounted on the back of your car, though, means that it’s not uncommon for you to go a few days without realizing that one of your bulbs is dead.

Make sure to install a replacement bulb as soon as you realize one of your brake lights is broken. If you are stopped by the police, you can get

  • a polite warning
  • You have 10 days to rectify it after receiving a roadside prohibition notice.
  • a PS60 fine and three license points
  • In the worst situation, they might tow your automobile away!

Checking your brake lights once a week is a smart idea not only to avoid being caught off guard, but also because it could prevent an accident since if they aren’t working, there will be no indication to oncoming traffic that you are stopping.

Should you swap out both brake lights at once?

According to logic, individual vehicle lights will eventually burn out and need to be changed the more you use them. Head lamp capsules need to wear out more quickly when driving at night or during the day. Right?

The manufacturer rates the lifespan of the lamps and bulbs in your car in terms of illumination hours.

Naturally, long-lasting, high-quality bulbs will endure longer than lights of lower quality.

Only when your car’s headlamp capsules and micro lamps burn out and stop working properly should you replace them.

As soon as your head lamp capsules burn out, you should replace them with a high-quality, durable capsule lamp, such those made by Champion lighting components. Considering that they are both the same age and level of deterioration, it is also advisable to replace the headlamp capsules, brake light, and taillight bulbs in pairs at the same time. Most likely, the opposite lamp capsule has significantly deteriorated and will also burn out shortly.

Find out more about high-quality lighting items, where to buy your car part, or how to locate it.

This article’s information is provided for educational reasons only and shouldn’t be relied upon in place of consulting a qualified technician or mechanic. We advise you to speak with a licensed technician or mechanic if you have any specific queries or issues regarding any of the subjects discussed here.

How much does a new brake light bulb cost?

Anyone can learn how to replace a broken brake light. By changing the bulb yourself instead of going to the store and waiting for the service to be done, you can save $20 in labor costs and travel time. A replacement bulb costs about $10.

How frequently should brake lights be replaced?

Since a brake light bulb should last about 40,000 miles, or a few years depending on your driving conditions, a few times during the year should be sufficient. If you’re in stop-and-go traffic, which is more frequent in a big city, a bulb can burn out more quickly.

Is the bulb used for both the brake and taillights?

The brake lights and tail lights on many cars use the same bulb. Inside the bulb, there are two filaments: one for the brake light and one for the taillight. Additionally, some automobiles feature a separate bulb for each circuit.

Is changing a brake light bulb simple?

Drive the holder and bulb into the tail light assembly, then tighten it by rotating the holder clockwise.

Make sure the tail light assembly’s bulb and holder are both firmly in place.

Have someone sit in charge and operate the brakes while you gaze behind and observe light movement.

It’s simple to replace a brake warning lamp. Without an expert’s assistance, you can carry it out on your own at home. But if you get stuck at any moment, you could need their assistance. Simply removing the old bulb and replacing it is all that is required.

When replacing a light bulb, you must remove screws with a flathead or screwdriver. You won’t even need one if your car’s design allows for simple access to the taillight housing.

At any time, your brake lights could malfunction. Police officers may swing by to make sure you are aware of the broken light bulb. The punishments in these circumstances may be a little severe.

If you just bought a car, you might be curious about how to change a brake light. Don’t disregard this problem because it might make nighttime driving uncomfortable. In order to prevent accidents, it’s critical to always drive with enough light. Be sure to seek the assistance of experts if you lack the confidence to complete this activity.

What does “check high mounted brake light” on your car mean?

These lights represent various potential problems with your braking system. Because every car is unique, yours can have a different brake warning indicator than these. To be confident which light applies to your individual car, consult the Owner’s Manual.

*Note: Although your car’s ABS Warning Lights are specifically tied to the Anti-Lock Brake System, they can occasionally be connected to the hydraulic braking system.

Is the brake light bulb the same in all cars?

It’s time to install the brake light bulb you choose after making your selection. If you’re feeling confident, you can replace the brake light bulb yourself at home on many cars because it’s not particularly difficult. Any queries you may have can be answered by your auto electrician.

Here is a step-by-step instruction manual for changing your brake light bulbs. Please remember that this is simply a general overview. Since every automobile is unique, some bulbs might not be able to be changed in this manner. We strongly advise you to consult the car manual or speak with your auto electrician if you have any questions.

The bulbs in brake lights all the same?

While the brake lights only activate when the brake pedal is pushed, the tail lights turn on instantly when the driver turns on the headlights. Even though both lights are red, brake lights often have a red light that is significantly brighter.

Depending on the type of vehicle. Dual-filament bulbs are used in many automobiles to combine the brake and tail lights into one. Here, every filament is connected to a different circuit. The thicker filament, which provides a brighter light, is utilized for brake lights, while the thinner filament illuminates as a tail light. While in certain automobiles, the brake and taillights are lit by independent lightbulbs.

Let’s look at what those lights are and what they function in order to better comprehend the distinctions between the brake light and the tail light.

The three bulbs in a tail light are what?

Electrically speaking, the vast majority of tail lights contain three-wire, dual filament “1157”, “2057”, or “2157” bulbs. As a result, the running and brake lights can operate separately. You might notice that one side of your running light or brake light stops working if a bulb’s filament burns out. The burned bulb is typically pretty simple to identify. If the burned filament in the bulb isn’t immediately apparent, you can simply switch the bulbs from one side of the car to the other to make sure. The bulb is the issue if the issue spreads to the other tail lamp.

What is a relay for turn signals?

Your car’s turn signal lights are managed by an electronic component called a turn signal relay, sometimes referred to as a flasher relay. Typically, the turn signal relay is what makes the clicking noise when you turn on your turn signals.