Reset the system each time a tire’s inflation pressure has been adjusted, a wheel has been replaced, or a tire has been replaced.
Lightly press button 1 on the indicator lever several times up or down until the relevant symbol and the word RESET show up in the display.
Press button 2 for approximately 5 seconds to display the reading at the top right.
Start your car. The corrected inflation pressures will be used as nominal values after a few minutes of driving. Upon successful completion of the system reset, the indicator lamp turns off.
Contrary to popular belief, a flat tire monitor is not the same as a tire pressure monitor (FTM). The actual inflation pressure in the tires is not measured by an FTM system.
As you drive, the FTM compares the speeds of the different wheels and employs the Dynamic Stability Control (DSC) and Antilock Braking System (ABS) sensors to detect a tire pressure loss. The rolling circumference and, consequently, the rotation speed of the afflicted wheel alter when there is a pressure drop. When the system notices this, a flat tire is reported.
The FTM is no longer used in vehicles going to North America since it is a less reliable monitoring system. Additionally, TPM systems call for the installation of a sensor (integrated with the valve stem) on every wheel. Wheel sensors are not used by FTM systems.
Your tires are NOT properly filled using the Tire Pressure Monitor (TPM) device. As stated on the Wheels and Tires page, TPM isn’t obliged to sound an alert until the tire pressure is 25% below the recommended level. That is hardly enough to support the vehicle’s maximum load and well below the pressure needed for safe driving. The TPM system is not meant to be a monitor to make sure your tires are inflated properly, but rather as a last-minute warning before impending tire failure.
In This Article...
Tire Pressure Monitoring System (TPMS) Light Reset by BMW
The TPMS (Tire Pressure Monitoring System) on a BMW is designed to warn you when a tire’s pressure is too low and might result in hazardous driving conditions. If the indicator is on, your tires may not be properly inflated, which might result in premature tire wear and even tire failure. It’s crucial to comprehend the significance of appropriate tire inflation and how TPMS can aid with tire maintenance.
On a 2018 BMW, how do you reset the tire pressure light?
Click car, vehicle status, tire settings, and tire pressure monitor from the home menu. Select to do a reset when the automobile is stopped and the engine is running. For the reset to be completed, you will need to take a little drive.
How much time does it take to reset a BMW’s tire pressure monitor?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. To allow the sensors to reset, start the automobile and let it run for 20 minutes.
Why, when my tires are fine, BMW, is the tire pressure light on?
What it means: Your vehicle’s tire pressure will be too low and the BMW tire pressure monitoring system (TPMS) will notify you. When air pressure is 25% below the usual suggested pressure for your BMW model, the warning light turns on. Low tire pressure could put your BMW at danger for tire failure, excessive tire wear and tear, handling issues, and decreased fuel efficiency.
What to do if it comes on: Turn off your car and check the pressure in each tire if the TPMS light comes on when you start it. Ensure that the tires are inflated to the optimum pressure. The recommended tire pressure is printed in your owner’s handbook or on a placard inside the driver-side door of your car.
Find a gas station with air pumps, check the tire pressure, and add air as necessary if the TPMS indicator illuminates while you are driving. The TPMS light will also come on if your tire suddenly flattens as a result of damage. Pull over right away and inspect your tires if you see this light and experience a difference in how your car handles. Many BMW automobiles come with run-flat tires already mounted from the manufacturer with no spare tire. If so, move cautiously to a BMW service center in the area. You will need to hire a tow truck if you have fitted aftermarket tires that are not run flats.
It often denotes a TPMS malfunction if the indicator glows and flashes. The first step is to check the pressure in each of your tires once more and add air if needed. Your best option is to take it to a qualified BMW mechanic for diagnosis if the TPMS light is still on after adding air.
Note: Extreme weather changes can have an impact on tires, particularly in the colder winter months. It’s a good idea to inspect your tires each month.
What actions are required to turn off the light: If your tire pressure is too low, you should fill them up with air and then reset your TPMS (see the directions in your owner’s manual to do this). If this doesn’t work, you’ll need to visit your local BMW repair shop for an accurate diagnosis.
Should your tire pressure light be reset?
You should first check the pressure in your tires. Remember to check every tire, including your spare. It should reset your tire pressure indicator as long as your tires are correctly filled and fall within the acceptable range for your car.
You might need to fix your tire, have your TPMS examined, or try one of the following if the light is still on after setting the tire to the appropriate PSI:
- Drive for ten minutes. Attempt to reach a speed of 50 MPH.
- A TPMS reset button or process may be available in your car’s vehicle control center. Examine a professional or consult your owner’s manual (highly recommended).
Important information: If the pressure isn’t set to the car’s specifications, resetting the TPMS with a button or the vehicle control center may have negative effects.
Les Schwab experts are familiar with the reset processes to complete the task if those solutions don’t work. Each sensor can be programmed into the computer system of your car using tools we have. The next time you start your car or truck, or a few miles down the road, the indicator light ought to go out once your tires are correctly inflated or repaired.
What PSI should the tires on a BMW be?
To ensure a safe ride, you should check the tire pressure on your BMW. Although 32 PSI (pounds per square inch) is the recommended tire pressure for most BMW models, you should always double-check by examining the sticker on the inside edge of the driver’s door.
How can you turn off the low tire pressure light?
When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car and let it run for 20 minutes to let the sensor reset. Under the steering wheel is normally where you’ll find the reset button for the tire pressure monitor. If you can’t find it, consult the owner’s manual for your vehicle.
How can the TPMS on a 2007 BMW X5 be reset?
- Set the ignition to the ON position (engine off)
- From the iDrive menu, choose SETTINGS.
- Choose VEHICLE.
- Choose TPM.
- Choose RESET.
My tire pressure is fine, so why won’t the light go off?
When the TPMS warning light illuminates, proceed with caution. This indicates that at least one of your tires may be at least 25% under-inflated.
*The simplest way to get the most accurate reading is to check the tire pressure before you drive on it when the tire is “cool.” If your TPMS light is on, first check that you have correctly reset your TPMS by following these instructions.
Will my TPMS light automatically turn off if I fill my tires with air after it illuminates?
Several minutes after reinflating the tires to the prescribed pressure, the TPMS light ought to go out.
What happens if I adjust the tire pressure but the light on my tire pressure gauge still doesn’t go out?
The only place that can fix a computer issue that causes the TPMS warning light to turn ON and flash ON for one second and OFF for three seconds is the dealership service center. When the TPMS warning light illuminates and remains on, one or more tires may have low tire pressure. The light ought to go out once the tire is inflated to the recommended tire pressure listed on the door placard. Always check the pressure in all of your tires because one or more of them may not be at the proper pressure.
Why, after filling the tires, is the tire pressure light still on?
If you’ve inflated your tires, but the air pressure warning light continues to flash, your tire pressure monitoring system is malfunctioning or you have a gradual leak. A bright TPMS warning light indicates a problem with a tire pressure sensor, assuming there isn’t a leak in your tire. One of them might be damaged, the lithium-ion battery might be dead, or the TPMS itself might have an internal problem. You’ll need to get your Tire Pressure Monitoring System repaired in any of these scenarios.
Quick Tip: Recheck the tire to ensure it is inflated to the correct air pressure if the TPMS warning light illuminates again after you have inflated it. Low tire pressure indicates an air leak, which requires repair or tire replacement.
I have a low tire pressure light on. Can I drive?
Is Driving Secure? You should be able to continue driving safely for a few more miles until you can add air if your tire pressure is only slightly low. Extremely low tire pressure can cause tires to fail. This could lead to a blowout, which could be quite deadly.
What malfunctions the tire pressure sensor?
A problem with the tire pressure monitoring system is indicated by the message “Tire Pressure Sensor Fault” (TPMS). Most likely, a tire pressure sensor or the connection to the sensor has a problem.
The air pressure in the tires may be too low or high, or one of the tire pressure sensors may be broken, according to the error code.
Incorrect wiring, a malfunctioning TPMS control unit, or a TPMS reset could potentially be at blame. The quickest approach to learn is to use an OBD2 scanner to read the fault codes from your TPMS control unit.
Is a flat tire a result of low tire pressure?
Don’t ignore the tire-pressure warning light if it turns on; you might be getting a flat. A tire’s tendency to lose around a pound of air pressure every month and a pound for every 10 degrees of temperature drop can cause low pressure, as can leaks.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
Without a reset button, how do you reset a TPMS?
The system must be put in relearn mode in order to reset the light. Make sure the tire pressures are all set evenly and according to the specifications first. To prevent the battery from going out, you might need to first connect a battery charger on low. All accessories must be turned off. After turning the key to the “On” position for 20 minutes with the engine off, drive the car at a speed of at least 16 mph for at least 7 minutes. The light will turn off once the relearn operation is complete. If the light does not turn off, the system needs to be fixed. Tire pressure sensors may need to be replaced because they can start to malfunction after 5 or 6 years of use.
The informative nature of the aforementioned claims warrants independent verification. kindly visit our