Where Is The Oil Filter On A 2005 Toyota Highlander

with 5 liters of filter Check the oil level after refueling.

The maintenance needed light on a 2007 Toyota Highlander can be reset in a few different ways.

When your maintenance light comes on, there probably is an issue. Check everything out and make sure your automobile is road-ready before you reset anything. Follow these instructions to clear the maintenance light on your 2007 Toyota Highlander Hybrid if the lights are the only issue:

  • Switch off the ignition.
  • As you restart the ignition, press and hold the odometer button.
  • Without starting the engine, turn the ignition to the on position.
  • Once the entire miles is displayed, press the odometer button.
  • Your maintenance light ought to briefly flash before going out.

Maintenance lights are not to be taken lightly. One fault with your engine could trigger serious problems like mechanical failures or even crashes! Before you reset your maintenance light, make sure everything is in working order.

Spend a few minutes with Jerry to reduce your auto insurance costs while the mechanic is looking at your vehicle. The Jerry app, a licensed broker, can help you quickly search and compare rates from more than 50 top providers. Jerry can assist you in purchasing your new plan and even in canceling your old one if you locate a lower rate.

What type of oil is used in a Toyota Highlander?

Use the right oil for your Toyota Highlander to maintain peak performance. What is the finest oil to use on the cherished family car, though? We’ve looked into the characteristics of good oils for Highlanders and what to look for while comparing prices.

Toyota Genuine full synthetic 0w-20 oil is the recommended lubricant for brand-new Toyota Highlanders. The manufacturer advises using Toyota Genuine full synthetic 5w-30 for older models.

For the Toyota Highlander to operate at its best, the full synthetic oil and oil filter should be changed every 7,50010,000 miles.

Your car’s engine is its beating heart, and by using the right oil, you may increase its lifespan and performance. The finest oil for the Toyota Highlander will be covered in this post along with how it differs from other oils available. Continue reading to get our responses to other frequently asked questions about oil and the Toyota Highlander maintenance plan.

We hope the links provided are helpful to you before you continue reading. We may receive a commission if you buy something after clicking on one of the links on this page, so thank you!

A 3.5 L Toyota Highlander uses how much oil?

The 2.7L 4-cylinder engine consumes 4.6 quarts of oil, while the 3.5L V6 engine requires 5.8 quarts. Both engine options are available for the 2018 Toyota Highlander.

Keep in mind that synthetic oil is recommended for both of these engines whenever you need to replace the oil!

It can be enjoyable to shop for a new automobile, but it’s not necessarily the best to do the same for your auto insurance. Thank goodness, the Jerry app has made it simpler than ever to compare prices on vehicle insurance.

The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy. Jerry will even assist you in combining your auto and house insurance for the greatest savings!

How much oil does a Toyota Highlander use, in quarts?

These guidelines were developed using an oil change on a 2018 Highlander XLE 3.5L V6. While you can apply the fundamentals to different models and years, you should always reference your owner’s handbook for details particular to your car.

Warm up the engine

Start your engine and let it run for a while in cold weather to thin out the air and improve oil flow. A level space is recommended for parking your Toyota Highlander. Once the engine has warmed up, shut it off.

Drain the old oil

The drain bolt can then be removed by crawling underneath your Highlander. Allow the oil to drain for at least 15 minutes into your drain pan or another suitable container.

To stop leaks, replace the washer in your drain bolt. The oil drain bolt should then be installed once more and tightened.

Remove the filter

A 2018 Toyota Highlander’s oil filter is located underneath the vehicle. Utilizing the Toyota Highlander oil filter wrench, remove the filter housing. Take off the O-rings and old filter from the housing. Verify that the engine surface is free of any adhesion to the filter gasket.

Install the new oil filter

Before installing the replacement filter, clean the engine block of any debris and residue. Place the replacement filter and O-rings inside the housing after lubricating them.

Put new oil in the engine

5.8 quarts of engine oil should be poured into the oil fill hole. Start the engine after replacing the fill cap and making sure it is properly screwed in. Time you let the engine run for a while, look for leaks from the oil filter and drain bolt.

Stop the engine and check the oil level

Stop and wait for three minutes after running the engine for a while. Check the oil level with the dipstick and add extra if necessary.

Dispose of the old oil according to regulations

Never dispose of used oil in the trash or on the ground. The environment could be harmed if this is done. The majority of states require businesses that sell motor oil to accept your used oil, as do service centers and establishments that change oil (like Jiffy Lube). For information on additional locations to recycle your oil, consult the websites of your state or municipal government.

How frequently should a Toyota Highlander have its oil changed?

Generally speaking, synthetic oil needs to be changed every 7,500 to 10,000 miles. For traditional oil, Toyota suggests changing your 2020 Toyota Highlander’s oil and filter every 3,000 to 5,000 miles.

How can you turn a Toyota Highlander’s maintenance light back on?

Toyota Highlander Maintenance Light Reset Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for another 10 seconds or so. You can hear a beeping noise in addition to the maintenance light beginning to flash. The light ought should thereafter go out.