superior than commonly used stamped steel or cast iron. built to last the lifetime of your car.
In This Article...
Finish off with a torque wrench
When you’re done, tighten the filter cap with a 3/8 drive torque wrench. 18.5 ft-lbs of torque is advised (or 25Nm). Never use an impact tool.
Description
The 14-flute design is in accordance with OEM guidelines and is ideal for removing oil filters and cartridge style filter systems from the following vehicles: Toyota Camry V6; Lexus ES, GS, IS, LX, NX, RC, RX; Land Cruiser; FJ; Highlander; RAV4; Tacoma; Tundra; and Venza. The oil filter housing is held in place by a 14-flute wrench, making removal simple and preventing cap stripping. The wrench is engineered to last the lifetime of your vehicle out of sturdy forged aluminum. Its quality greatly beyond that of other wrenches’ standard cast iron and stamped steel. This wrench resists corrosion and rust thanks to a specific anodized treatment finish in gunmetal.
What kind of wrench is required to replace an oil filter?
The head of a fastener, such as a nut or bolt, can be tightened or loosened with a socket wrench. It has a long handle to which various sized sockets can be fitted in order to tighten various sized fasteners. The socket wrench may occasionally have a ratchet handle that enables continuous turning without having to lift the instrument. It’s crucial to select the size socket wrench that matches the specific hardware for each individual project.
There are four standard socket sizes: 1/4 inch (0.6 cm), 3/8 inch (0.9 cm), 1/2 inch (1.3 cm), and 3/4 inch (1.9 centimeters). Additionally, different-shaped sockets are available, including six-point (hexagon), eight-point (double square), and 12-point, to fit different bolt heads (double hexagon). You run the risk of breaking the tool and hurting your hands if you select a socket that is too large. Additionally, certain socket wrenches are deeper than usual to accommodate bolts with protruding threads.
You must choose the right size socket wrench before starting a project, like changing the oil on your car. To allow the used oil to drain from the engine, you must first remove the oil drain plug using a socket wrench. Start the car up first to get the engine warmed up. This makes the oil thinner, enabling smooth drainage. After that, put jack stands under the vehicle, fully engage the parking brake, and switch off the engine. Next, look for the drain plug underneath the car; the hot engine should still have some heat left in it. The drain plug’s nut should be covered by a 3/8-inch (0.9 centimeters) socket, which should be inserted into the socket wrench and turned counterclockwise. The oil drain plug should be simple to open, allowing the used oil in the engine to be drained. To catch all the dripping oil, lay a bucket and some newspaper under the car’s engine.
How can a Toyota oil filter be removed without a wrench?
The Toyota oil filter can be removed at a low cost by using sandpaper. You may easily create a tight grip over the oil filter by wrapping the sandpaper over it. After ensuring that your sandpaper is well wrapped, simply pull it in the other direction. The force generated produced by doing so will enable you to remove the Toyota oil filter without the use of a wrench.
Is there an oil filter wrench made by Toyota?
Because they are machined in the USA from high-quality 6061 T5 aluminum, our Toyota oil filter wrenches are far stronger than cast or stamped alternatives. Additionally, we went a step further and strengthened the 3/8″ drive hub (anodized red) by fortifying it with tougher 7075 aluminum.
How frequently should a Toyota Tundra have its oil changed?
For traditional oil, Toyota advises changing your 2020 Toyota Tundra’s oil and filter every 3,000 to 5,000 miles. Generally speaking, synthetic oil needs to be changed every 7,500 to 10,000 miles. Remember that the best way to choose the intervals for your car is to consult your owner’s handbook and your dealer.
What alternative to the oil filter wrench is there?
Oil filter removal without a wrench has been made possible in numerous ways by human ingenuity.
Wrench for Belt Straps
- A belt.
- Sandpaper or rubber strips (optional).
- Safety glasses and gloves.
- Useless rags.
- draining dish.
- nice jack stands and jacks (depending on the location of your unit).
What is the finest tool for removing an oil filter?
Our Top Selections
- Oil Filter Wrench by Motivx Tools
- Standard Oil Filter Swivel Wrench, Lisle 57030.
- Three-jaw, two-way Neiko 03421A oil filter wrench.
- GOHAWKTEQ 3-Jaw Oil Filter Wrench is universal.
- Ingenious Tool for Removing Oil Filter Wrench.
- 3-Jaw Adjustable Magnetic Oil Filter Wrench, OEM TOOLS 25101.
Is an oil filter wrench necessary?
Apply a thin layer of fresh engine oil to the replacement filter’s gasket before manually threading it on. For ease of turning, some filters include a rubberized surface. With just a few excellent hand tightenings, every quality oil filter is built to maintain its seal for tens of thousands of miles. Unless your filter is one of those deeply recessed models with no room for your hands, you don’t need a wrench. (In that scenario, a cap wrench is the only option.) Turn the filter until the mounting plate of the filter feels barely in touch with the filter base. Then turn the screw a further half turn with the wrench.
If it’s been a long since you’ve purchased engine oil, the options could seem overwhelming. See the section below titled “What’s That Starburst?” for some kind advice.
A stripped-out oil-drain plug hole can be saved using this straightforward rubber plug. To install and remove the rod, insert it.
How big of a wrench do I need?
Even though a wrench can seem like a simple equipment to recognize and use for your upcoming project, it can be challenging to choose which type and size of wrench is best for you. Finding the appropriate wrench is challenging due to the many sizes and distinct wrench designs. In order to help you choose the right wrench for your upcoming DIY project, we’ve compiled a list of frequently asked questions about wrench sizes below.
What are SAE wrench sizes?
The acronym SAE is frequently used to indicate that a wrench size is a standard size. This indication indicates that, under the metric system, the wrench head size is measured in inches as opposed to millimeters. The sizes of common wrenches range from 1/4 inch to 2 inches. Additionally, large size wrenches in the 2 to 4 inch range can be purchased.
How are wrench sizes measured?
A wrench head will have a hexagonal form on the outside. A spanner is the separation between one flat side and the subsequent flat side of a hexagon. Typically, the spanner dimension of standard wrenches is used as a measurement. A 2-inch standard wrench, for instance, will have parallel flat sides on the hexagonal wrench head that measure 2 inches apart.
How do you figure out your wrench size?
Finding the right wrench size for your project can be difficult if you have a bolt or nut that needs to be adjusted with a wrench. You must measure the bolt first in order to determine the appropriate wrench size. Take the bolt’s diameter and multiply it by 1.5. For both metric and standard bolt sizes, this computation and conversion factor are appropriate. The resultant number will be the wrench size you require to correctly adjust the bolt.
For instance, double your bolt’s width by 1.5 if it is.5 inches. It will measure 0.75 inches, or 3/4 of an inch. A 3/4 inch wrench is required to adjust a.5 inch bolt size.
Do you need both standard and metric wrenches?
In the modern world, manufacturing can occur anywhere in the world. A piece of furniture from Sweden or the United States could be found equally frequently. A metric set of wrenches and a conventional pair of wrenches are both wise investments. Even though a conversion table can be used to convert the two sets, owning both sets of wrenches will help you always find the perfect fit.
Does the oil filter need to be filled before installation?
Your personal preference and the kind of vehicle you drive will determine this. If you have a large, heavy-duty truck, pre-filling the filter makes the operation simpler; however, if you’re just changing the oil in a smaller automobile, it’s not required.
Is it sufficient to hand-tighten an oil filter?
The information on product costs and availability is correct as of the specified date and time but is liable to change. This product can be purchased using any pricing and availability details that are shown on [relevant Amazon Site(s), as applicable] at the time of purchase.
Oil filters should, as a general rule, be hand tight plus an additional quarter turn. By doing this, the filter will be safe but not too tight. Overtightening can harm the filter or your car and make it more challenging to take the filter out in the future.
Oil filter pliers should be used because it is challenging to complete the final quarter turn by hand. They come in a variety of shapes and sizes, but the important thing is that they give you the leverage and grip needed to correctly tighten the filter.
Will WD40 lubricate the oil filter?
Note that in both cases, WD40 can aid in removing the filter. Warming the engine up might also be beneficial before removing the oil filter because the heat should assist the filter come loose. However, only run the engine for a short while, as it could get dangerously hot.
Toyota oil filters: Are they all the same?
Keep in mind that not all oil filters conform to Toyota’s exacting requirements. A non-Toyota filter element can not function as well and even clog, costing your engine money. Always specify a Genuine Toyota oil filter to save your engine (and your wallet).
How is the oil filter removed from a Toyota Tacoma?
Look in the engine compartment for the oil filter. On the engine’s lower right side is where the oil filter is located. With a wrench, turn the filter in the other direction to remove it. As you crank the wrench in a counterclockwise direction, it automatically tightens around the filter.