5 quarts of Castrol – EDGE 5W-30 Full Synthetic Motor Oil (Part No. 1598B1)
In This Article...
Exactly how much oil does a Toyota Highlander require?
These guidelines were developed using an oil change on a 2018 Highlander XLE 3.5L V6. While you can apply the fundamentals to different models and years, you should always reference your owner’s handbook for details particular to your car.
Warm up the engine
Start your engine and let it run for a while in cold weather to thin out the air and improve oil flow. A level space is recommended for parking your Toyota Highlander. Once the engine has warmed up, shut it off.
Drain the old oil
The drain bolt can then be removed by crawling underneath your Highlander. Allow the oil to drain for at least 15 minutes into your drain pan or another suitable container.
To stop leaks, replace the washer in your drain bolt. The oil drain bolt should then be installed once more and tightened.
Remove the filter
A 2018 Toyota Highlander’s oil filter is located underneath the vehicle. Utilizing the Toyota Highlander oil filter wrench, remove the filter housing. Take off the O-rings and old filter from the housing. Verify that the engine surface is free of any adhesion to the filter gasket.
Install the new oil filter
Before installing the replacement filter, clean the engine block of any debris and residue. Place the replacement filter and O-rings inside the housing after lubricating them.
Put new oil in the engine
5.8 quarts of engine oil should be poured into the oil fill hole. Start the engine after replacing the fill cap and making sure it is properly screwed in. Time you let the engine run for a while, look for leaks from the oil filter and drain bolt.
Stop the engine and check the oil level
Stop and wait for three minutes after running the engine for a while. Check the oil level with the dipstick and add extra if necessary.
Dispose of the old oil according to regulations
Never dispose of used oil in the trash or on the ground. The environment could be harmed if this is done. The majority of states require businesses that sell motor oil to accept your used oil, as do service centers and establishments that change oil (like Jiffy Lube). For information on additional locations to recycle your oil, consult the websites of your state or municipal government.
Describe SAE 5w30.
A popular motor oil for light-duty gasoline and diesel engines is 5w30. 5w30 is a multi-grade oil, like the majority of modern motor oils, ranging from a lower viscosity grade of 5 to a higher viscosity grade of 30.
The “W” stands for “winter; the number before it denotes the thickness or viscosity of the oil at low temperatures (thus the “W”); the number following it denotes the thickness or viscosity of the oil at higher temperatures, when the engine is operating.
A Toyota Highlander: Does it require synthetic oil?
Oil is essential for maintaining a clean, cool engine in any car, including the Toyota Highlander. Your engine’s moving parts are lubricated, which helps to stop wear and tear.
The oil in your car is thick and cold when you first start it. As the engine warms up, the oil thins and flows more swiftly. This makes it possible for it to more efficiently lubricate the engine parts.
Toyota advises using full synthetic oil in the Highlander for maximum performance and engine protection. But which viscosity should you pick?
For newer Toyota Highlander models, Toyota Genuine full synthetic 0w-20 oil is the best option. However, it is advisable to choose complete synthetic 5w-30 oil if you have an older model with higher mileage.
Depending on the year and mileage, a Toyota repair may occasionally suggest using a complete synthetic 5w-20.
Full synthetic oil will not only guarantee that your engine is operating at peak efficiency, but it will also allow you to travel 7,50010,000 miles between oil changes.
The normal oil can still be used, but you will need to change it every 3,500 to 5,000 miles. Additionally, synthetic oil and your engine won’t be protected by conventional oil if you drive a lot.
For more information on the recommended oil for your specific Highlander model, be sure to consult your owner’s manual or with a Toyota-certified repair. Your car can need a different type of oil depending on its year and mileage.
Do I need synthetic oil for my Toyota?
Only Toyota cars (apart from 3UR-FBE Engines*) that require 0w-20 synthetic oil have been given the go-ahead for longer oil change intervals of 10,000 miles or 12 months. (You should, though, keep checking the oil level frequently and topping off as necessary. This will enable your engine to benefit fully from synthetic oil.)
What is the purpose of 5W-30 motor oil?
Generally speaking, 5W-30 motor oil is a winter viscosity grade. Although it functions satisfactorily at greater temperatures, its best application is for drivers in colder climates.
It is often advised for petrol vehicles or a light-duty diesel engine because of its lower viscosity. In addition to these uses, 5W-30 multigrade oil is also employed for the following things:
- Since it is less prone to thermal breakdown, it is better for drivers who frequently experience temperature fluctuations.
- Some individuals might switch to this oil in the winter because it offers superior engine protection and aids in removing engine deposits in lower temperatures.
- For low-duty application in light vehicles and passenger cars
- For engines not operating under excessive pressure
Let’s look at some of the most frequently asked questions regarding 5W-30 motor oil now that we understand what it is used for.
My 2005 Toyota Camry will take synthetic oil, is that okay?
The 2005 Toyota Camry 2.4L recommends using AMSOIL OE Synthetic Motor Oil since it is specifically designed for the longer oil change intervals. Longer than the conventional 3,000-mile oil change interval, it includes innovative synthetic technology that resists chemical breakdown for ultimate wear protection for your car.
How often should the oil be changed in a Toyota Highlander?
One of the most fundamental and important maintenance for your car is an oil change. For conventional oil, Toyota suggests changing your 2021 Toyota Highlander’s oil and filter every 3,000 to 5,000 miles. Normally, synthetic oil needs to be changed every 7,500 to 10,000 miles.
What is engine oil 0W 20?
In colder temperatures, 0W-20 motor oil flows as freely as 0 Weight oil, but once the engine reaches operating temperature, it behaves more like 20 Weight oil. This guarantees that oil will begin to flow through the engine right away, lubricating important engine components even in cold weather.
The ‘W’ in viscosity descriptions does not, contrary to popular belief, stand for weight. In actuality, it represents Winter. This means that synthetic 0W-20 oil performs as a 0 Weight oil in cold areas but becomes as thick and viscous as a 20 Weight oil once the typical engine temperature has been attained.
Castrol EDGE, a cutting-edge full synthetic 0W-20 motor oil, is part of the company’s line of low viscosity 0W-20 lubricants. It is our toughest oil and is made to endure high temperatures and pressure. For those who want to push their car to the limit, it’s the perfect choice. Full synthetic 0W-20 motor oil liquid Castrol GTX MAGNATEC is designed with protective, clever ingredients that offer outstanding wear prevention.
How can you turn a Toyota Highlander’s oil light back on?
Turn the ignition to position one after inserting your key (the first setting before actually starting the car). Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for another 10 seconds or so.
How do you oil a Toyota Highlander from 2005?
Toyota Highlander (2001-2007) Base 3.3L V6 Oil Change Instructions
- Take off Oil Fill Cap – Remove the oil fill cap.
- Add Oil – Select the proper sort of oil and add it.
- Replace the oil fill cap by placing it back on the engine.
- Additional details about applying oil are available.
Are SAE and synthetic 5W-30 the same thing?
SAE 30 and 5w30 are not the same thing, to be clear. Because SAE 30 is a single-grade oil, it can only withstand one very high temperature rating. With a rating of 30, this high temperature is in the center. Contrarily, 5w30 is a multi-grade oil with two grades. It is rated at 30, which also applies to high temperatures, yet at low temperatures, it is classified at 5. This low-temperature grade is indicated by a “w, which stands for winter. These are the technical variations, but in the parts that follow, I’ll go into greater detail about each characteristic and application.
Low-Shear-Rate Viscosity for 5w30 and 5w40
At 100g, the viscosity of 40 ranges from 12.5 to 16.3 mm2/s. At 100g, the operating viscosity of 30 ranges from 9.3 to 12.5 mm2/s. Both oils are 5 grade while they are cold, however at operating temperatures, 5w30 becomes 30 grade and 5w40 becomes 40 grade. With greater temperatures in the summer, 5w40 has a higher viscosity than 5w30, which aids in the motor’s continual operation.
High-Shear Rate Viscosity
This value is a minimum of 3.5 at 150g for a working viscosity of 40. The value of this parameter at 150g must be at least 2.9 for a working viscosity of 30. This indicator largely reveals how much the oil can withstand under harsh loads.
Application
Although it may be utilized by various types of cars and in a variety of temperatures, 5w30 is best in colder climates. Higher mileage engines frequently employ 5w40, which operates better in warmer climates.