Check the manufacturer’s specification for the precise requirements before tightening the serpentine belt on your Toyota Yaris. I’m unable to answer your question without more details (such the model year, engine, and trim level), as it changes amongst versions. However, the method for doing so is rather straightforward once you decide where it should be. The drawback is that it needs the Denso BTG20 Belt Tension Gauge, a unique belt tensioner tool. Although there are workarounds, it’s essential to make sure you’re at the right standard. The serpentine belt tensioner pulley will then need to be adjusted to lock in your new tension, which should hopefully stop any drive belt squealing you may have had.
You must change the tensioner on a Toyota Yaris in order to tighten a serpentine belt.
Finding the tensioner bolt in the hole on the pulley of the serpentine belt on a Toyota Yaris will allow you to tighten it.
In This Article...
Why is the Yaris in my Toyota squealing?
The engine bay of some 2007 Yaris cars could make a screeching noise. Toyota claims that the serpentine drive belt slipping on the various pulleys is one potential source of the noise.
The squeal should stop after replacing the drive belt with part number 90916-02500, an improved design belt, and tightening the belt in accordance with updated specifications.
Installing the new belt will begin the repair. After stretching the belt for around 20 minutes, start the engine and then turn it off.
Place a belt tension gauge in the span illustrated in the aforementioned figure and tighten the belt until the tension gauge reads 102-123 ft-lbs.
Simply measure the belt’s deflection in the span region of the figure if you don’t have a tension gauge. The belt should deflect after being appropriately tightened. 410-.450 inches.
Jim DePalma, a 30-year car repair industry veteran who has held positions as a service manager, parts manager, and ASE-certified technician, is the author of “Factory Fixes.” His column offers actual factory technical service bulletins (TSBs), which have been shortened for easier reading, from vehicle manufacturers. Before beginning work on a vehicle, Mr. DePalma recommends technicians to always verify with a dealer or service information system for the most recent changes. By email, you can get in touch with him at [email protected].
What about the Toyota Yaris’ serpentine belt?
Serpentine belt replacements for Toyota Yaris typically cost between $59 and $72. Between $38 and $48 is the expected cost of labor, while between $21 and $24 is the estimated cost of parts. Taxes and other fees are not included in this range, nor are your particular model year or geographic area taken into account.
A Toyota Yaris has how many belts?
The accessories in or on the engine of your Toyota Yaris are powered by the drive belt(s) by using the engine revs. Your alternator, water pump, air conditioning compressor, and power steering are a few examples.
Most Toyota Yaris models feature one or two drive belts, which are sometimes referred to as serpentine belts. The belt can be formed of perishable materials like rubber, neoprene, or urethane and must be flexible to move over pulleys.
The driving belt belt(s) are tensioned and mounted on pulleys. This keeps the belt in position and gives the attachments the power required to perform properly. The accessories’ performance could suffer or cease entirely when the belt begins to wear, is damaged, or breaks.
Drive belts for Toyota Yaris vehicles should be changed as necessary or at the predetermined service period as specified in the service manual. Drive belts occasionally get damaged or need to be replaced earlier than anticipated, thus it’s advised to check them at every service.
Depending on the sort of drive belt(s) being replaced and whether additional engine parts need to be taken out to gain access, the cost to have a Toyota Yaris drive belt(s) replaced ranges from $100 to $400+.
When the drive belt tension has changed and it has to be replaced or rebuilt, you may occasionally hear a noise warning. Your drive belt may be signaling that it requires maintenance if you hear screeching during or shortly after vehicle starts.
How much does a serpentine belt replacement cost?
A common serpentine belt costs no more than $75 and starts at about $25. You could change the belt yourself if you have a basic understanding of auto repair, which might save you between $75 and $120 in labor costs. You should budget between $100 and $195 to replace your serpentine belt altogether.
The straightforward fix for this issue shouldn’t take more than an hourtwo at most. It depends on the car’s model and how simple it is to access the serpentine belt inside the chassis of the vehicle.
How can you tell when a belt tensioner needs to be replaced?
Appearance: Using a wrench to impart torque to the arm, move the tensioner (installed on the engine) through its full range of motion (from stop to stop). The tensioner arm need to operate freely and smoothly. Replacement of the tensioner is necessary if you notice a binding, sticking, or grinding tensioner arm.
What results in a serpentine belt rupturing?
Serpentine belt issues typically have one of three root causes: faulty belt tensioners, pulley misalignments, or faulty bearings in the tensioner, idler, or one of the belt-driven accessories (including the water pump).
How much does a Toyota Yaris serpentine belt replacement cost?
Depending on your car model and region, the serpentine belt replacement repair might cost between $75 and $190. What you need to consider is as follows: New parts should cost between $25 and $70. The estimated labor costs are $50 to $120.
What occurs if a serpentine belt becomes slack?
An automatic belt tensioner, a self-tensioning system, is a common feature of modern vehicles. These tensioners are made to maintain a specific level of tension on the serpentine belt, ensuring that it runs smoothly and keeps your automobile moving.
Your serpentine belt resembles a massive, quickly rotating rubber ring. It must also maintain a balance between flexibility and tension, much like a rubber band. The majority of tensioners have an internal spring and pulley that exerts the necessary force against the serpentine belt to maintain tension. A belt may slip, scream, or run hot if there is insufficient tension. In the worst instance, a slack belt can slip off of its pulleys. The vehicle will then stop running and all the engine-powered gadgets will malfunction.
A quick fact is that if your serpentine belt is slack, you can also have a malfunctioning water pump, which might overheat the engine. Avoid losing performance. Bring in your vehicle as soon as you can. We’ll look after you.