Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
In This Article...
How can the Toyota maintenance light be reset?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
How can I turn off the maintenance is necessary light?
The Maintenance Required Light that flashes on the instrument panel is reset using the processes that Lexus walks us through.
Keep in mind that after doing maintenance, the light should be reset using the following procedure:
- the ON position on the ignition switch
- Set the trip display to TRIP A mode on the odometer.
- Switch the ignition to the “OFF” position.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- The service reminder light for maintenance will
The Trip Meter RESET button should be released.
7. Insert the key in the OFF position.
8. Ensure the Service Maintenance Reminder Light turns off by turning the ignition to the ON position. NOTE: If the light in step 5a keeps flashing, turn off the ignition and follow the steps from step 1 again.
How do you turn off the Toyota Camry’s maintenance needed light?
Push and hold the odometer button on your dashboard briefly, then quickly turn your key to the second position. Hold the odometer button down for a further 10 seconds. The maintenance light should flash and you could hear a beeping if everything is done correctly. Your Toyota Camry’s maintenance light ought to go out after doing that.
Why does my Toyota says maintenance required?
- If the car is on, turn it off.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Now the light will read “MAINT REQD.”
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- The ODO display will briefly flash before beginning to display only zeros.
- Press and hold the ODO reset / readout button while the engine is off.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
What happens after I change the oil in my car?
Reset Oil Change Indicator
- Turn on the ignition.
- Both the stop and accelerator pedals should be fully depressed.
- Maintain firm pressure on the brake and accelerator pedals.
- A notice verifying the reset process is ongoing appears after three seconds.
Why, after an oil change, is my maintenance required light still on?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
On a 2010 Toyota Camry, how do I turn the maintenance light back on?
Have you changed your oil or had other standard vehicle maintenance performed, but the light is still on? When you are driving through the Buford and Alpharetta areas, this can be annoying and disconcerting. Do not worry! Resetting the maintenance light on your Toyota Camry is a simple procedure. Simply adhere to the instructions below:
- Turn the ignition to position one after inserting your key (the first position before actually starting the car).
- Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position.
- Hold the odometer button down for a further 10 seconds. You can hear a beeping noise in addition to the maintenance light beginning to flash. The light ought should thereafter go out.
- Release your grip on the odometer button once the maintenance light has gone out, then turn the key to start your automobile. Once your Camry starts, the light ought to be off. To stop the Toyota Camry’s maintenance light from coming on, perform this procedure one or two more times.
How can I disable the Toyota RAV4’s maintenance alert?
How to Extinguish the Toyota RAV4’s Maintenance Light
- Put your key in the ignition. Turn the key to the first position.
- On the dashboard, press the reset trip meter button. Hold it down for a couple of seconds.
- Hold the odometer button down for another ten or so seconds.
- Once off, release the odometer button.
How can I turn off the Toyota Corolla’s maintenance is required light?
Turn the key back to the “On position after finding the “trip reset button once more. Hold the trip reset button down until your odometer lights 0 miles. The maintenance light will thereafter go out.
On a 2010 Toyota Corolla, how do you turn the maintenance light back on?
Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for around 10 seconds. A buzzer sound and the maintenance light should start to flash. The light ought should thereafter go out.
Even though my automobile says maintenance is necessary, can I still drive it?
Simply put, the flashing maintenance required light is alerting you that maintenance on your car is necessary. The indicator will come on when a predetermined period of time has passed since your car’s last service or based on how far you’ve driven it.
This light typically indicates that you should change the oil in your car. The maintenance data will be reset for you when your car has been taken in for service.
To manually reset the system to turn off the light, however, follow these instructions:
When the maintenance light comes on, you can continue to drive, but bear in mind that you are doing so at your own risk if the required or scheduled repair is skipped.
Is the maintenance needed light always on?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.