- Make sure the tires are filled appropriately.
- Don’t start the engine; instead, turn the ignition switch to the On position.
- Find the TPMS Set button, which is usually located beneath the steering wheel.
- Keep holding down the Set button.
- Once the warning light has flashed three times, let go of the Set button.
In This Article...
How do I reset my 2019 Highlander’s TPMS?
Turn the key to the “on” position with the car off, but don’t let it run. When the Toyota tire pressure sensor blinks three times, hold down the TPMS reset button until it stops blinking. Start the car, then let it run for 20 minutes to let the sensor reset.
How can you turn a 2013 Toyota Highlander’s tire pressure light back on?
1) As stated on the tire and loading information label, set the tires to the prescribed (cold) pressures. 2) Switch the ignition on. 3) When the tire pressure warning light blinks three times, press and hold the tire pressure warning reset switch for at least three seconds (one second on, one second off).
The TPMS reset button is where?
Tire pressure monitoring system is referred to as TPMS. The TPMS reset button is often located below the steering wheel. Your car’s TPMS needs to be electronically reset after you replace the tires in order to erase the error message. Hold the TPMS reset button down until the tire pressure light blinks three times, then let go of the button to complete the process. Your car should be started, and the sensor will refresh after 20 minutes.
Why are my tires fine but my TPMS light is on?
It’s likely that one or more of your tires have low air pressure if you see the tire pressure indicator turn on. However, even if your tires are in good condition, there are a number of things that could cause the sensors to go off, so you shouldn’t rely only on the data from the tire pressure monitoring system of your car.
We’ve talked about some additional aspects of automobile maintenance in this piece. Read these articles if you have some time:
How can a TPMS light be turned off?
Don’t start the car; just turn the key to “on.” Till the tire pressure light blinks three times, press and hold the TPMS reset button. Press the button again to start the vehicle. Within twenty minutes, the light ought to turn off.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
Where are TPMS installed?
In the US, direct TPMS usage is more prevalent. The sensors are either housed in the tire pressure valve, which also serves as an antenna, or they are band-clamped to the wheel rim. These gadgets deliver the data to an on-board computer.
Can I drive with my TPMS on?
There are several possible meanings when you see that silly little light with the exclamation point glaring back at you. It’s frequently anything as harmless as temperature changes that result in a change in the tire’s air pressure. In more severe situations, a puncture or other damage has caused the tire to lose pressure. The sensor can also be activated and result in the light coming on if your tires are overinflated.
Is It Safe To Drive With TPMS Light On?
To avoid seeming like Debbie Downer, we’ll simply say no. Driving around with your TPMS light on is not safe. You can’t tell how quickly your tire is losing air or how long it has been over- or underinflated without doing a tire examination. The best course of action is to check the current inflation level of each tire with a tire pressure gauge.
When the tire inspection light appears while you are driving, slow down and get to the closest gas station or service facility.
How much does a TPMS sensor replacement cost?
Best in Automotive Repair Replacement of a TPMS sensor typically costs between $203 and $245. While parts are priced between $149 and $177, labor costs are predicted to be between $54 and $68. Taxes and other costs are not included in this range, nor are your particular vehicle or geographic area taken into account.
Will TPMS be reset if the batteries is disconnected?
Each vehicle has an onboard computer, which occasionally experiences technical difficulties. Resetting the computer is the best approach to address these issues, and you may do this by removing and reinserting the battery. Locate the negative terminal of the battery by opening the hood of your car. Press the car’s horn to drain any leftover power after removing the negative connector to disconnect the battery. Once the positive terminal is connected again, the TPMS warning light should stop flashing.
What does the triangle in a Toyota Highlander with the exclamation point mean?
Have you ever been operating your Toyota Highlander when a symbol suddenly appeared on the dashboard? If so, then every sign has a unique meaning. Everybody occasionally gets a visit from a dashboard light.
While some lights are only indicators, others are alarms indicating your Highlander requires regular upkeep or repairs. It’s crucial to understand what each dashboard light on your vehicle indicates.
An indication light is any light that appears on the Toyota Highlander’s dashboard and is either blue or green. A light that alerts you that anything in your car is on is what an indicator light does exactly as it sounds. The majority of the time, it indicates on your dashboard whether a Highlander feature has been activated or canceled.
Some of the typical warning lights that you might see are listed below:
- TRAC OFF Indicator: This light appears to alert you to the need to turn off the vehicle’s traction control and/or stability control systems.
- The VSC/TRAC OFF Indicator shows whether the traction control or vehicle stability control systems are activated or off. To turn off the light, push and hold the switch while the car is still moving.
- An icon resembling a speedometer serves as a visual cue that the cruise control system is engaged.
- An emblem in the shape of a key will display on your Toyota Highlander’s dashboard to let you know that the security system is operating as intended.
- Headlight High Beam Indicator: This blue light signifies the active state of the headlight high beams.
- Turn Signal Indicator: These green lights signify that the Highlander’s right or left turn signal has been engaged.
Your Toyota Highlander will have a warning light if it has a yellow or red light. A warning light is typically an issue that needs to be resolved right away in order to keep your SUV in the finest condition possible. If you notice any of the lights listed below, get in touch with our service staff to arrange a visit:
- Master Warning Light: When the master warning system detects a problem, a triangle with an exclamation point inside of it shows on the dashboard and a buzzer sounds.
- When an icon resembling an old-fashioned oil can appears, it means your oil pressure is too low and should be checked. Low Engine Oil Pressure Warning Light: You should take immediate action to address this problem in order to prevent potential engine damage.
- Electric Power Steering (EPS) Warning Light: It’s critical to have your Highlander evaluated if this warning light, which looks like a steering wheel next to an exclamation point, comes on your dashboard.
Do 2007 Toyota Highlanders come equipped with TPMS sensors?
All American-made automobiles must have direct or indirect TPMS systems fitted as of 2008 as a result of the TREAD Act’s 2007 mandate.
The Toyota Highlander has a direct TPMS system fitted, which means the wheel has TPMS sensors. In the event that one or more tires on a Direct TPMS vehicle show low tire pressure, the TPMS sensors will communicate this information to the car’s ECU. Each tire pressure or an indicator light (low-line TPMS system) will be displayed on the dashboard (high-line TPMS system).
After a sensor change or tire rotation, a TPMS relearn is advised. A TPMS relearn is necessary to transmit sensor data to the vehicle’s ECU when services, such as tire changes or TPMS sensor replacements, are carried out on one or more tires of a Toyota Highlander.
TPMS reset button, closed-loop
A “SET” or “TPMS RESET button can be found on some Toyota vehicles and is either under the glove box or beneath the steering wheel. The system searches for the already-stored sensor IDs when the button is pressed. The “SET button can be utilized while replacing tires, changing or altering tire pressure, changing tire size, or conducting a tire rotation with differing tire pressures in the front and back.
The ECU must be unlocked in order for the relearn method to function properly if the “SET button is pushed after new sensor IDs are introduced but before a relearn is carried out. A few sophisticated TPMS diagnostic tools can unlock the ECU. You can successfully complete the relearn procedure if your TPMS scan tool offers the “UNLOCK ECU option.”
My Toyota TPMS has to be reset.
Resetting the Tire Pressure Light on a Toyota Turn the key to the “On position when the car is off, but don’t let it run. When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car and let it run for 20 minutes to let the sensor reset.
Why does the TPMS light continue to illuminate?
When the TPMS warning light illuminates, proceed with caution. This indicates that at least one of your tires may be at least 25% under-inflated.
*The simplest way to get the most accurate reading is to check the tire pressure before you drive on it when the tire is “cool.” If your TPMS light is on, first check that you have correctly reset your TPMS by following these instructions.
Will my TPMS light automatically turn off if I fill my tires with air after it illuminates?
Several minutes after reinflating the tires to the prescribed pressure, the TPMS light ought to go out.
What happens if I adjust the tire pressure but the light on my tire pressure gauge still doesn’t go out?
The only place that can fix a computer issue that causes the TPMS warning light to turn ON and flash ON for one second and OFF for three seconds is the dealership service center. When the TPMS warning light illuminates and remains on, one or more tires may have low tire pressure. The light ought to go out once the tire is inflated to the recommended tire pressure listed on the door placard. Always check the pressure in all of your tires because one or more of them may not be at the proper pressure.
Do tire sensors automatically reset?
Additionally, once the car has been driven for a while, the TPMS system will reset itself. A technician can change the inflation pressure, rotate, or replace sensors.