- Put the ignition on with your key. Turn the key to the first position.
- On the dashboard, press the reset trip meter button. Hold it down for a few seconds.
- Hold the odometer button down for around five seconds.
- Release the odometer button after it is off.
In This Article...
On a Toyota Rav4, how do you change the maintenance light?
In order to start the car, turn the ignition to position one with your key in the ignition. Turn the key to position two while pressing and holding the trip meter reset button on the dashboard. For 10 seconds, keep your finger on the odometer button. Then the light should flash, beep, and finally turn off.
How do I remove the warning about Toyota maintenance?
Turn your key to the second position after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a total of 10 seconds. The light ought to flash, potentially beep, and then go off as a result. Release the odometer button once it has been turned off, then start the automobile.
Why does my Rav4 indicate that maintenance is needed?
The significance of the emblem MAINT REQD is significant. The MAINT REQD light indicates when the vehicle’s scheduled maintenance is due when it illuminates. If your car is under two years old, this service can be covered by your ToyotaCare plan.
How can I dim the maintenance is necessary light?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
How should I respond if my maintenance light illuminates?
How Can the Maintenance Required Light Be Reset?
- Turn on your car. Look at your dashboard when your key is in the on position.
- Press the Trip Meter Reset Button after turning off the engine.
- Re-start the vehicle.
- Keep pressing the reset button.
- Reset button released
Why does my Toyota state it needs maintenance?
- Now the light will read “MAINT REQD.”
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- If the car is on, turn it off.
- Press and hold the ODO reset / readout button while the engine is off.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- The ODO display will briefly flash before beginning to display only zeros.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
Why, after an oil change, is my maintenance required light still on?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
How can I turn my car’s service light back on?
First, turn on the engine. Step 2: The display will say “Service required” if a service is overdue. Locate and press the OK button at the top right of the steering wheel for longer than one second to clear this message. The service interval will be reset to its default value in Step 3.
Even though my automobile says maintenance is necessary, can I still drive it?
Simply put, the flashing maintenance required light is alerting you that maintenance on your car is necessary. The indicator will come on when a predetermined period of time has passed since your car’s last service or based on how far you’ve driven it.
This light typically indicates that you should change the oil in your car. The maintenance data will be reset for you when your car has been taken in for service.
To manually reset the system to turn off the light, however, follow these instructions:
When the maintenance light comes on, you can continue to drive, but bear in mind that you are doing so at your own risk if the required or scheduled repair is skipped.
Why does my car indicate that maintenance is needed?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.
Why does my automobile need servicing when it flashes?
If you’re unsure of what a warning light on your dashboard indicates, it can make you feel uneasy. Thankfully, you normally don’t need to worry about it.
A flashing maintenance light is typically your car’s method of telling you that it needs to be serviced soon. The light’s purpose is to alert drivers when it might be time for an oil change or a tune-up by turning on at predetermined intervals.
You have roughly 500 miles left before you need to have your automobile serviced when the light first starts flashing. Your maintenance light will inform you by turning on and staying on when it’s due for service.
Download Jerry, the super insurance expert app, to find the answers to all of your maintenance-related concerns.
Jerry is a powerful tool for finding vehicle insurance discounts, and it can do so in just 45 seconds! Jerry will evaluate prices from the leading insurance companies in the country to get you the cheapest offers, and if you decide to transfer, he can even cancel your current policy!