A Toyota Prius’ maintenance light can be reset easily and quickly in a matter of minutes. Start by parking the car and closing all of the doors. Don’t start the engine while turning the ignition key to the ON position. If your ignition is a push button, you must press the start/stop button twice without applying the brake. To access the settings menu, use the arrow navigation buttons in the left cluster of steering wheel controls. Select OK once you’ve navigated to the menu for the car settings. Select MAINTENANCE SYSTEM, then hit OK. Look for OIL MAINTENANCE on that menu, then hit OK once again. When a confirmation notice appears, choose YES, and then click OK. To confirm that the reset has been retained, turn off the ignition and then start the car.
Toyota Priuses’ “maintenance required” light can be reset by pressing the power button twice, the odometer button, which is located below the multifunction display, once to turn the vehicle off, the odometer button, while holding it down, and the power button twice (2 times), all while keeping your foot off the brake. Hold the odometer button down while you wait for the flashing dashes to stop and the reading to return.
For a 2014 Prius, turn the trip odometer to “trip A,” start the vehicle, push and hold the MPH/KMH button, turn the ignition off while holding the button, turn the ignition back on while holding the button, and watch the reset take place.
Thank you for your clear instructions; I was able to accomplish what the Toyota Service Department failed to do.
In This Article...
How can the maintenance needed light on a 2009 Toyota Prius be reset?
This belongs in the category of “very old news, but I’m writing it for a purpose. Her maintenance request light was on, so I just received a call from a customer asking to book a 5K service. We recently completed a service roughly 2,000 miles ago, according to my review of her paperwork. Oops! It’s ridiculous, I know. She agreed to reset the light herself, so I promised to send her some instructions.
I had originally planned to copy and paste some instructions off the internet since, well, why recreate the wheel? Anyone who is familiar with tech support is probably also comfortable using Google and copying and pasting.
The trouble is, none of the directions I discovered truly appealed to me. There were numerous places where the reader could become perplexed and make mistakes. I therefore made the decision to draft my own directions. My instructions might end up being just as poorly written as the ones I found in the Google highlighted snippet. I occasionally experience editing blindness. I read what I was thinking when I proofread rather than what I had really written. You be the judge, I say.
Yet another version of: How to reset the maint req light on a 2004-2009 Prius
1. Switch on the power to “By *not* stepping on the brake pedal and twice pushing the power button, the ON position is selected.
2. Push the ODO/TRIP button underneath the dash display until the mileage is displayed (not Trip A or Trip B)
3. Switch on the device’s power “by *not* stepping on the brake pedal and pressing the power button once to the OFF position.
4. Push the ODO/TRIP button and hold it down. Hold on till Simon commands.
5. Switch on the appliance “By *not* stepping on the brake pedal and twice pushing the power button, the ON position is selected.
6. Hold the ODO/TRIP button down until the odometer displays “000000.
7. And that’s it. You can release the ODO/TRIP button, according to Simon. The next time you Ready the car, the maintenance necessary light must be off.
On a 2010 Toyota Prius, how do you reset the oil maintenance light?
If you often perform maintenance on your 2010 Toyota Prius, the tiny maintenance required light might become very aggravating. It will only take a few minutes to correct, though, and is extremely simple. Follow these steps to reset the oil maintenance light on a 2010 Toyota Prius:
- The primary display should turn on in the center of the dashboard.
- Resetting oil maintenance data should be visible on the display.
- To get to Trip A, push the Trip button on the steering wheel.
- Press the push-button start once to turn the car off.
- As you double-tap the start button, keep your foot off the brake.
- While pushing the push-button start twice, press and hold the mph button that is immediately above it.
It’s best to get regular oil changes to keep your Prius in good condition. You may also reset the maintenance light in a matter of minutes. But did you know that by downloading the Jerry app and comparing prices, you can also save hundreds on auto insurance in only a few minutes?
Jerry is a certified insurance broker who offers estimates from numerous reputable and highly rated auto insurance providers. Jerry can assist you in purchasing insurance and terminating your current policy after you discover a fantastic cost for your Toyota Prius. Customers often save close to $900 annually!
Why does the maintenance light not go out?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
How can the maintenance needed light on a 2010 Toyota be reset?
How Can the Maintenance Required Light Be Reset?
- Turn on your car. Look at your dashboard when your key is in the on position.
- Press the Trip Meter Reset Button after turning off the engine.
- Re-start the vehicle.
- Keep pressing the reset button.
- Reset button released
How can I turn off the Toyota maintenance is required light?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
Why, after an oil change, is my maintenance required light still on?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
My maintenance is necessary light is on, why?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.