In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
In This Article...
How can I dim the maintenance is necessary light?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
Why does my car indicate maintenance is needed following an oil change?
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Now the light will read “MAINT REQD.”
- Press and hold the ODO reset / readout button while the engine is off.
- The ODO display will briefly flash before beginning to display only zeros.
- If the car is on, turn it off.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
How do you repair a Toyota Corolla maintenance needed light?
In order to make “Trip A” appear on the main screen, press and hold the trip reset button next to the odometer. Reset the key to “Off.” Turn the key back to the “On position while pushing the button to reset the trip. Hold down the trip reset button until the odometer’s miles section flashes zero.
How can I turn off the Toyota Camry’s maintenance is required light?
Push and hold the odometer button on your dashboard briefly, then quickly turn your key to the second position. Hold the odometer button down for a further 10 seconds. The maintenance light should flash and you could hear a beeping if everything is done correctly. Your Toyota Camry’s maintenance light ought to go out after doing that.
How can you turn a 2018 Toyota Corolla’s maintenance light back on?
You must keep up with routine maintenance, but if you do the tire rotations and oil changes yourself, you will need to reset the maintenance light once you have completed the servicing.
- Put the Corolla’s keys in. Activate the lock on the “OFF position; do not start the vehicle.
- the trip reset button next to the odometer is pressed and held until “On the main screen, Trip A may be shown.
- Reverse the key to “OFF.
- Turn the key back to the “on” position while pressing the button to reset the trip “position of ON.
- Hold down the trip reset button until the odometer’s miles section flashes zero. The maintenance light will now stop flashing.
Why does the maintenance required message on my 2017 Toyota Corolla?
It’s a light that is always on and alerts you when you require an oil change at a licensed auto shop. Your Toyota will run more smoothly and efficiently if you change the oil in your car. In the long run, you will end up saving a ton of money because it will also reduce component wear and tear.
Every 5,000 miles, this light automatically comes on as a reminder for you to replace the oil in your automobile. You can still use your automobile safely while the light is on in your dashboard because the light itself does not indicate that your car has been damaged.
The Toyota maintenance light solely depends on the odometer to calculate those 5,000 miles, so it is unable to determine whether you had your oil changed in the interim. Because of this, this light may start to annoy you if it flashes on your dashboard after you just changed your oil.
You may need to manually reset the maintenance required light if the mechanics who change the oil in your Toyota vehicle forget to do so.
Even though my automobile says maintenance is necessary, can I still drive it?
Simply put, the flashing maintenance required light is alerting you that maintenance on your car is necessary. The indicator will come on when a predetermined period of time has passed since your car’s last service or based on how far you’ve driven it.
This light typically indicates that you should change the oil in your car. The maintenance data will be reset for you when your car has been taken in for service.
To manually reset the system to turn off the light, however, follow these instructions:
When the maintenance light comes on, you can continue to drive, but bear in mind that you are doing so at your own risk if the required or scheduled repair is skipped.
Why does my Toyota’s maintenance indicator constantly flashing?
Toyota’s maintenance reminder system only serves to remind the motorist to have their car’s oil changed. The engine light will turn on after 5,000 miles of driving since the computer counts the engine’s mileage from the time it was reset. The system does not account for the changes between mild and extreme driving situations, load weight, towing, or weather conditions, all of which are significant factors that affect oil life because it is not algorithm driven, unlike other more sophisticated maintenance reminder systems.
Because of this, people who regularly tow or drive in adverse weather conditions and require more frequent oil changes may find the maintenance light ineffective. However, for individuals who frequently use the motorway in good weather, it might not be practical. This is not to suggest that a driver should completely ignore the maintenance light. Keep an eye on your driving circumstances throughout the year and, if necessary, have a professional assess your unique, most frequent driving conditions to determine whether or not your car need servicing.
The table below can help you estimate how frequently you would need to change the oil in a current car (earlier cars typically require more regular oil changes):
Why is still on my maintenance light?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
On a 2010 Toyota Corolla, how do you turn the maintenance light back on?
Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for around 10 seconds. A buzzer sound and the maintenance light should start to flash. The light ought should thereafter go out.