Make sure the tire pressures are accurate before resetting the system. After starting the car, hold down the reset button while doing so. On the instrument panel, it is located low and to the right of the steering wheel. Hold down the button until the instrument panel’s tpms indicator light blinks gently three times.
The 2010 Toyota Corolla’s reset button for the tire pressure light can be found on the instrument panel, within the glove compartment, or on the knee bolster. Hold on until there are three light flashes.
The best option is to have the shop remove the sensors the next time you buy tires and replace them with regular fill valves. Discover how to inspect your tires like your father did. has no expense at all
In all honesty, I own a 2010 Corolla and have been a licensed auto technician for 36 years. I am aware of Al’s concerns with the intermittent on-and-flashing of the tps light. If you give it some thought, the solution is actually rather straightforward! The first thing to note is that modern cars include a variety of control modules, each of which functions as the system’s brain. The computer or module is configured to keep all tires within 3-6 psi of the manufacture requirements, which are on your door jam. You also have sensors that feed that module or brain, providing information about how the system is operating and performing (drivers). As long as a pressure stays within the manufacturer’s specifications, the light on your dash won’t turn on. If it is too high or low, however, the sensors will transmit signals to the module, which will turn on the light. Now, if the light is constantly on, there may be a sensor or pressure problem. Now, if the light is always flashing, there is probably an issue with the computer or a module. If you visit a store and scan the module, it will provide the information you need. A DTC is a diagnostic problem code. The scanner will read the code and will immediately inform you of the precise problem with that d**n bulb! If you discover a DTC saved in the TPMs module, it will generally be code: C2141 the computer or module has a problem with that code.
In This Article...
On a 2010 Toyota Camry, where is the reset button for tire pressure?
Open the glove box to reveal a reset button that is tucked away beneath a little lip to the left of the glove box. Hold down the button until the TPMS light gently blinks three times.
How much pressure should the tires of a 2010 Toyota Corolla be?
You should use different tire pressures for the front and rear wheels of the Toyota Corolla. Utilize the following advice: 38 psi in the front tires. 36 psi in the rear tires.
Where is the button to reset my TPMS?
Tire pressure monitoring system is referred to as TPMS. The TPMS reset button is often located below the steering wheel. Your car’s TPMS needs to be electronically reset after you replace the tires in order to erase the error message. Hold the TPMS reset button down until the tire pressure light blinks three times, then let go of the button to complete the process. Your car should be started, and the sensor will refresh after 20 minutes.
How can I turn off the tire pressure warning light?
How to Clear the Tire Pressure Indicator
- Don’t start the car; just turn the key to “on.”
- While the car is off, disconnect the positive battery cable.
- All tires, including the spare, should be 3 PSI overinflated before being entirely deflated.
- Bring your car to our service department for qualified help.
Why, Toyota, does my tire pressure light remain on even after filling the tires?
Try the following if your TPMS light is still on after you have inflated your tires to the recommended pressure: 10 minutes at a speed of 50 mph would be plenty. When you start the car again, the TPMS light ought to be off because this ought to reset the tire sensors.
Why, after filling the tires, is the tire pressure light still on?
If you’ve inflated your tires, but the air pressure warning light continues to flash, your tire pressure monitoring system is malfunctioning or you have a gradual leak. A bright TPMS warning light indicates a problem with a tire pressure sensor, assuming there isn’t a leak in your tire. One of them might be damaged, the lithium-ion battery might be dead, or the TPMS itself might have an internal problem. You’ll need to get your Tire Pressure Monitoring System repaired in any of these scenarios.
Quick Tip: Recheck the tire to ensure it is inflated to the correct air pressure if the TPMS warning light illuminates again after you have inflated it. Low tire pressure indicates an air leak, which requires repair or tire replacement.
Why is the Toyota Corolla tire pressure warning light blinking?
What Does a Flashing TPMS Light Indicate? The tire pressure sensors are powered by a battery, thus if the TPMS indicator is blinking, the battery might need to be changed. It might potentially point to a sensor-related issue.
What is the Toyota Corolla’s typical tire pressure?
How can I determine my Corolla’s tire pressure? Comparing the valve reading to the 32 PSI tire pressure advised for your Corolla If the pressure in your tires is too low, blow air into them until they reach 32 PSI. To release some air if your tire pressure is too high, push the valve in.
What is the Toyota Corolla’s recommended tire pressure?
pressure in a Toyota Corolla tire The 2019 Toyota Corolla’s recommended minimum tyre pressure is 35 psi, according to this tire placard. This is equivalent to 2.4bar and 240kPa.
TPMS reset button, closed-loop
A “SET” or “TPMS RESET button can be found on some Toyota vehicles and is either under the glove box or beneath the steering wheel. The system searches for the already-stored sensor IDs when the button is pressed. The “SET button can be utilized while replacing tires, changing or altering tire pressure, changing tire size, or conducting a tire rotation with differing tire pressures in the front and back.
The ECU must be unlocked in order for the relearn method to function properly if the “SET button is pushed after new sensor IDs are introduced but before a relearn is carried out. A few sophisticated TPMS diagnostic tools can unlock the ECU. You can successfully complete the relearn procedure if your TPMS scan tool offers the “UNLOCK ECU option.”
On a Toyota Corolla, where is the reset button located?
Put the maintenance light out.
Corolla, Toyota Put the Corolla’s keys in. Don’t start the car; instead, turn the key to the “On position. In order to make “Trip A” appear on the main screen, press and hold the trip reset button next to the odometer. Reset the key to “Off.”
How can the VSC light be turned off on a 2010 Toyota Corolla?
Vehicle Stability Control, or VSC as it is commonly known, is the stability control system used in Toyota automobiles. By lowering or eliminating the power provided to your wheels, stability control aids in the maintenance of traction and control in your vehicle. By automatically providing brake pressure to up to three wheels, it achieves this. The system’s main objective is to keep your car traveling in the direction of its wheels. Since 2012, at least in the USA, it has become a necessary safety requirement. Naturally, VSC OFF denotes that your Toyota’s stability control is turned off.
VSC Light Easy Fix
Depending on the model year of the Toyota, a button with the same icon as the light in your gauges will be located either next to your shifter or next to your steering wheel. When you’ve found it:
- Ensure that you have come to a complete stop. If you can, put the car in park.
- For a few seconds, hold down the VSC button.
- The indicator lights for TRAC OFF and VSC OFF will turn on. Now both systems are off.
- Once more, press the VSC button. As soon as both lights go out, the systems are back in operation.
If the VSC OFF light is still on, there can be a glitch in your car’s computer or a problem with the VSC system. Bring your car to a Toyota service location near you so a qualified technician can check the codes and identify the problem. Although it is safe to drive your Toyota even with the VSC OFF light on, we advise caution, especially in bad weather.
In Need of Repair?
Bring your car to the Toyota of Arlington servicing facility if you live close to Chicago and need repairs. We can install OEM parts for you because we have access to them. Get a free estimate from our outstanding collision facility if you need body work.
On a Toyota Corolla, how do you turn off the service light?
Turn the key back to the “On position after finding the “trip reset button once more. Hold the trip reset button down until your odometer lights 0 miles. The maintenance light will thereafter go out.
Why won’t my tire pressure warning light turn on?
If your tires are properly inflated yet the warning light continues to illuminate, you may have a leak or a TPMS issue in one or more of your tires. To determine if a tire has a leak is not difficult. Simply double-check the air pressure in each of your tires with your tire gauge. If all of the tires have the proper air pressure, one or more tire pressure sensors are likely to be at fault, necessitating repair work on your tire pressure monitoring system. You’ll need to replace or repair the tire if you notice that one or more of your tires’ air pressures have fallen.
In what location is the TPMS sensor?
In the US, direct TPMS usage is more prevalent. The sensors are either housed in the tire pressure valve, which also serves as an antenna, or they are band-clamped to the wheel rim. These gadgets deliver the data to an on-board computer.