Make sure the tire pressures are accurate before resetting the system. After starting the car, hold down the reset button while doing so. On the instrument panel, it is located low and to the right of the steering wheel. Hold down the button until the instrument panel’s tpms indicator light blinks gently three times.
The 2010 Toyota Corolla’s reset button for the tire pressure light can be found on the instrument panel, within the glove compartment, or on the knee bolster. Hold on until there are three light flashes.
The best option is to have the shop remove the sensors the next time you buy tires and replace them with regular fill valves. Discover how to inspect your tires like your father did. has no expense at all
In all honesty, I own a 2010 Corolla and have been a licensed auto technician for 36 years. I am aware of Al’s concerns with the intermittent on-and-flashing of the tps light. If you give it some thought, the solution is actually rather straightforward! The first thing to note is that modern cars include a variety of control modules, each of which functions as the system’s brain. The computer or module is configured to keep all tires within 3-6 psi of the manufacture requirements, which are on your door jam. You also have sensors that feed that module or brain, providing information about how the system is operating and performing (drivers). As long as a pressure stays within the manufacturer’s specifications, the light on your dash won’t turn on. If it is too high or low, however, the sensors will transmit signals to the module, which will turn on the light. Now, if the light is constantly on, there may be a sensor or pressure problem. Now, if the light is always flashing, there is probably an issue with the computer or a module. If you visit a store and scan the module, it will provide the information you need. A DTC is a diagnostic problem code. The scanner will read the code and will immediately inform you of the precise problem with that d**n bulb! If you discover a DTC saved in the TPMs module, it will generally be code: C2141 the computer or module has a problem with that code.
In This Article...
How much pressure should the tires of a 2010 Toyota Corolla be?
You should use different tire pressures for the front and rear wheels of the Toyota Corolla. Utilize the following advice: 38 psi in the front tires. 36 psi in the rear tires.
Why is my tire pressure light on when my Toyota Corolla’s tires are fine?
Several cars now come with a built-in tire pressure monitoring system (TPMS). An indication light will flash on your dashboard if the air pressure in your tires drops below the recommended level.
The information system in the dashboard may have a menu that shows you which of the four tires is malfunctioning. The TPMS indicator may be on in a number of circumstances, however your tires may not require replacement or upkeep.
If this occurs and all of your tires seem to be in good condition. This light may illuminate even if your tires are in good condition for a number of different reasons. The decrease in outdoor temperature is one explanation. To double-check and confirm it, it is advisable to maintain a tire pressure gauge in the automobile.
Where is the button to reset my TPMS?
Tire pressure monitoring system is referred to as TPMS. The TPMS reset button is often located below the steering wheel. Your car’s TPMS needs to be electronically reset after you replace the tires in order to erase the error message. Hold the TPMS reset button down until the tire pressure light blinks three times, then let go of the button to complete the process. Your car should be started, and the sensor will refresh after 20 minutes.
Why is the Toyota Corolla tire pressure warning light blinking?
What Does a Flashing TPMS Light Indicate? The tire pressure sensors are powered by a battery, thus if the TPMS indicator is blinking, the battery might need to be changed. It might potentially point to a sensor-related issue.
What is the Toyota Corolla’s typical tire pressure?
How can I determine my Corolla’s tire pressure? Comparing the valve reading to the 32 PSI tire pressure advised for your Corolla If the pressure in your tires is too low, blow air into them until they reach 32 PSI. To release some air if your tire pressure is too high, push the valve in.
Why is the Toyota tire pressure warning light blinking?
The tire pressure monitoring system, or TPMS, in your automobile is designed to alert you when the air pressure in your tires is low. If one or more of your tires are underinflated, the TPMS will activate.
My tire pressure is fine, so why won’t the light go off?
When the TPMS warning light illuminates, proceed with caution. This indicates that at least one of your tires may be at least 25% under-inflated.
*The simplest way to get the most accurate reading is to check the tire pressure before you drive on it when the tire is “cool.” If your TPMS light is on, first check that you have correctly reset your TPMS by following these instructions.
Will my TPMS light automatically turn off if I fill my tires with air after it illuminates?
Several minutes after reinflating the tires to the prescribed pressure, the TPMS light ought to go out.
What happens if I adjust the tire pressure but the light on my tire pressure gauge still doesn’t go out?
The only place that can fix a computer issue that causes the TPMS warning light to turn ON and flash ON for one second and OFF for three seconds is the dealership service center. When the TPMS warning light illuminates and remains on, one or more tires may have low tire pressure. The light ought to go out once the tire is inflated to the recommended tire pressure listed on the door placard. Always check the pressure in all of your tires because one or more of them may not be at the proper pressure.
Why, after filling the tires, is the tire pressure light still on?
If you’ve inflated your tires, but the air pressure warning light continues to flash, your tire pressure monitoring system is malfunctioning or you have a gradual leak. A bright TPMS warning light indicates a problem with a tire pressure sensor, assuming there isn’t a leak in your tire. One of them might be damaged, the lithium-ion battery might be dead, or the TPMS itself might have an internal problem. You’ll need to get your Tire Pressure Monitoring System repaired in any of these scenarios.
Quick Tip: Recheck the tire to ensure it is inflated to the correct air pressure if the TPMS warning light illuminates again after you have inflated it. Low tire pressure indicates an air leak, which requires repair or tire replacement.
My tires are in good condition, so why is my low tire pressure sign on?
Typically, a tire with an air pressure that is 10% to 15% low will turn on the warning light. The air pressure inside the tires also tends to drop in cold or icy conditions. Short trips in the car will warm up the tires and raise the pressure in them.
On a 2010 Toyota Camry, how do you reset the tire pressure light?
Resetting the Tire Pressure Light on a Toyota Turn the key to the “On position when the car is off, but don’t let it run. When the tire pressure light blinks three times, release pressure on the TPMS reset button. Start the car and let it run for 20 minutes to let the sensor reset.
TPMS reset button, closed-loop
A “SET” or “TPMS RESET button can be found on some Toyota vehicles and is either under the glove box or beneath the steering wheel. The system searches for the already-stored sensor IDs when the button is pressed. The “SET button can be utilized while replacing tires, changing or altering tire pressure, changing tire size, or conducting a tire rotation with differing tire pressures in the front and back.
The ECU must be unlocked in order for the relearn method to function properly if the “SET button is pushed after new sensor IDs are introduced but before a relearn is carried out. A few sophisticated TPMS diagnostic tools can unlock the ECU. You can successfully complete the relearn procedure if your TPMS scan tool offers the “UNLOCK ECU option.”
On a Toyota Corolla, where is the reset button located?
Put the maintenance light out.
Corolla, Toyota Put the Corolla’s keys in. Don’t start the car; instead, turn the key to the “On position. In order to make “Trip A” appear on the main screen, press and hold the trip reset button next to the odometer. Reset the key to “Off.”
How can the VSC light be turned off on a 2010 Toyota Corolla?
Vehicle Stability Control, or VSC as it is commonly known, is the stability control system used in Toyota automobiles. By lowering or eliminating the power provided to your wheels, stability control aids in the maintenance of traction and control in your vehicle. By automatically providing brake pressure to up to three wheels, it achieves this. The system’s main objective is to keep your car traveling in the direction of its wheels. Since 2012, at least in the USA, it has become a necessary safety requirement. Naturally, VSC OFF denotes that your Toyota’s stability control is turned off.
VSC Light Easy Fix
On a 2010 Toyota Corolla, how do you turn off the VSC light?
The stability control system used in Toyota automobiles is known as VSC, or “Vehicle Stability Control.” By lowering or stopping all power transmitted to your wheels, stability control helps your car retain traction and control. This is accomplished by delivering brake pressure automatically to up to three wheels. The system’s main objective is to maintain the direction of travel of your car. Since 2012, at least in the USA, it has been required by law as a vital safety element. Obviously, VSC OFF indicates that your Toyota’s stability control is not engaged.
- Ensure that you have come to a complete stop. If you can, put the car in park.
- For a few seconds, hold down the VSC button.
- The indicator lights for TRAC OFF and VSC OFF will turn on. Now both systems are off.
- Once more, press the VSC button. As soon as both lights go out, the systems are back in operation.
If the VSC OFF light is still on, there can be a glitch in your car’s computer or a problem with the VSC system. Bring your car to a Toyota service location near you so a qualified technician can check the codes and identify the problem. Although it is safe to drive your Toyota even with the VSC OFF light on, we advise caution, especially in bad weather.
In Need of Repair?
Bring your car to the Toyota of Arlington servicing facility if you live close to Chicago and need repairs. We can install OEM parts for you because we have access to them. Get a free estimate from our outstanding collision facility if you need body work.
How can the dashboard lights be turned on in a 2010 Toyota Corolla?
Congratulations on purchasing your first automobile! I’m delighted to report that the Corolla’s *dashboard light controls** make it simple to turn on and adjust your dashboard lights. Use them as follows.
Typically, when you start your automobile, your dashboard lights should come on. If they don’t, your dashboard light controls may have them completely dimmed.
Find the dashboard light switch to the left of the steering wheel once your car is running. This will either be a knob or a wheel, depending on the year of your Corolla. Next to the control, you should see a tiny image of your speedometer. You can adjust the brightness or dimness of your dashboard light with the control.
If the dashboard lights are still not functioning, a fuse may have blown. Although they are quite simple to replace, you’ll need to see a professional.
It’s a big thing getting your first car! You might have to pay more for insurance if you’re a new driver or a young one. With Jerry, the insurance super app, you can make sure you’re getting the most affordable insurance imaginable! For free, instant, affordable insurance quotes, download Jerry today!