While turning the ignition on, press and hold the odometer/trip display button. Press and hold the button for five seconds before releasing it. Press and release the button in 5 seconds. The reset value will appear on the display.
In This Article...
When should a Toyota Hilux’s timing belt be replaced?
Almost every auto owner wonders how frequently they should change their timing belt.
As a result of advancements in both technology and automobiles, several manufacturers now advise intervals of up to 100,000 miles rather than the previous standard of 60,000.
Timing belt replacement for the Toyota Hilux is advised every 100,000 miles or every six years, whichever comes first.
However, this figure may change based on how frequently you drive your car and how much care you give it.
For that extra peace of mind, it can be worthwhile to replace the timing belt sooner if you operate your Hilux frequently and roughly.
On a Toyota Fortuner, how do you reset the timing belt light?
Hello, at 204 000 kilometers, the timing belt light turned on yesterday. (2012 Fortuner) The light was reset after the old one had been replaced at 150 000 miles. There are no sensors or tools that I am aware of that can activate the T-belt light. Everything seemed to be in order after I opened and examined the timing belt.
Perhaps someone is aware of the potential cause of activation. (The tensioner was used to replace the timing on the 150 000)
The light is set to 150 000 ks when the timing belt is replaced. Whoever reset it simply changed the value to 100,000 ks. The warning indicator lacks a sensor. It merely keeps track of the mileage. To count down the remaining 50 000 ks, just reset the light.
The steps are as follows:
1. Verify that the meter is in ODO mode.
2. Switch the ignition off.
3. While continuing to hold down the trip reset button, turn on the ignition.
4. Press and hold the button for 5 to 10 seconds before letting go.
5. The display will show the number 15. This appears to be the default setting.
6. Now quickly press the button. Every time a button is pressed, the value will increase by 1. Press down consistently until the number 5 shows on the screen. The number should increase to 20, then it should reset to 1. Keep pressing till you see 5 if you missed it the first time.
7. After the right value shows, hold down the button while pressing it until the ODO display reappears.
If you followed the instructions correctly, the Timing Belt light should turn off.
How can you tell if your timing belt needs to be replaced?
The motor may make a ticking noise as the timing belt begins to deteriorate. Examine your oil and, if the level is within a normal range, get your mechanic to check your timing belt as soon as possible. This ticking sounds can also be a symptom that your engine has low oil pressure or is not properly lubricated.
What occurs if the timing belt snaps?
Some engine parts can malfunction without causing significant harm. Without any issues, you can drive to your mechanic and get the part replaced. But with a timing belt, this is not the case. The camshaft will stop turning when the timing belt snaps, but the crankshaft will continue to rotate at 1000 revolutions per minute. Because of this, the pistons will keep rising and falling in their cylinders and, occasionally, may hit the valves. The pistons, valves, and cylinder heads will sustain damage when this occurs, and because to how quickly it occurs, the damage will be almost immediate.
It is crucial to pay close attention to your engine and make sure it is operating smoothly. Take your car to a repair right away if you begin to notice any of the aforementioned symptoms. It can be nothing, only require a quick correction, or indicate more serious issues that could develop into the dreaded timing belt failure while driving. Come to Professional Auto Repair’s shop and let us examine your timing belt and other parts to ensure that your car is working properly.
How can the timing belt light on a Landcruiser 100 series be turned off?
a) With the ignition ON, flip the display to ODO using the trip switch (select/reset button), then turn the ignition OFF.
b) Press and hold the trip switch for five seconds while turning on the ignition.
d) T-belt mode on the digital display should be activated. The initial display reads “15” (0,000km) (ie. 150,000km).
2. REWRITING SUBSTITUTE VALUES
Each time the trip switch is pressed when the T-Belt mode is engaged, the displayed value is adjusted by 10,000km. After reaching ” 20 ” (200,000km), the display changes back to ” 1 ” (10,000km). Keep in mind that after reset, this counter will start at zero and represents the distance to be traveled before the next light turns on.
I believe the timing belt replacement interval for all 100 series engine variations is 150,000 kilometers, but this should be verified with the servicing recommendations of the various markets. Given this, there shouldn’t be a need for you to alter the default option of “15.”
The ODO is in miles for the US, so it stands to reason that the T-Belt warning would be set at intervals of 10,000 miles.
3. COMPLETION OF T-BELT WARNING RESET
a) After changing the setting value, hold the trip switch ON for at least five seconds before releasing it.
b) Verify that the warning light has turned off when the engine is started and that the display has now reverted back to ODO.
NOTE: The T-Belt warning IS reset if the T-Belt mode is finished even if the belt replacement has not been done.
As usual, everyone takes no responsibility, so I hope this helps. 😉
How much does a timing belt replacement for a Hilux cost?
Your Toyota Hilux’s timing belt needs to be replaced at the suggested intervals to keep it in good running condition.
Failure to do so may result in engine damage when the timing belt fails, which typically necessitates costly towing fees and significant repairs.
While the expense of replacing your Toyota Hilux timing belt may come as a bit of a shock, replacing your engine due to failure is much more expensive.
If other engine parts need to be removed in order to access the timing belt, the cost of a replacement timing belt might rise to over $1500 on average.
Can I change the timing belt on my own?
It does need some engine knowledge to replace a timing belt and water pump, so if you don’t have much expertise working under the hood, we advise leaving it to the experts. However, if you prefer making your own repairs and restorations, you can do it yourself and avoid paying hefty repair expenses in the process.
Starting with the tools you’ll need, we’ll walk you through the replacement of a timing belt and water pump step by step.
What You’ll Need to Replace the Water Pump and Timing Belt
- bags made of plastic and a permanent marker (for labelling nuts, bolts and parts you remove from the engine)
- a fresh timing belt
- Set of Allen keys
- Wrench socket set
- Tip-Ex, white chalk, and white paint (for marking the cogs for simpler reassembly)
- tools for driving screws, such as Philips and slot drive
- leather gloves
- jar or bucket (for collecting coolant)
- new antifreeze/coolant
- a fresh water pump
Step 1: Preparation
Get your car and work area ready first. Depending on your degree of experience, changing a timing belt and water pump can take anywhere from one to three hours, so make sure you have the time and space necessary. Before you begin, carry out the following:
- To reach the undercarriage beneath the engine, jack up the front of the automobile.
- Before starting, make sure the engine is entirely cool.
- To stop the engine from spinning while you’re removing the timing belt, put the engine in drive and use the handbrake.
- Prepare all of your tools, and have bags and a pen on available to name and store the engine parts you remove.
- Since coolant will spill out when you remove the water pump, place a bucket underneath it. To find the pump, see your car’s manual.
Step 2: Removing the Belts
You must first remove the fan belt and power steering belt because they are located next to the cover that protects the timing belt and water pump. To remove the belts, take the following actions:
- Crankshaft pulley: Loosen. To access the engine and remove the bolt, you’ll need a long wrench arm.
- To access the timing case and crankshaft pulley, do the same with the power steering belt by moving it aside.
- The fasteners holding the alternator in place should be loosened. The fan belt can then be removed by lightly tapping it.
How long is the lifespan of a Toyota timing belt?
Timing belts are important, but unless your Toyota owner’s handbook specifically advises it, they don’t need to be replaced on a regular basis. Between 60,000 and 100,000 miles, some automakers advise changing the timing belt, while others don’t. Many timing belts available now can last 100,000 miles or more before they need to be replaced.
Warning Signs a Timing Belt Replacement is Needed
The majority of timing belts require replacement every 60,000 to 90,000 miles. Because it is crucial to the engine’s functionality, the timing belt acts inside the engine. Don’t put off changing the belt until it breaks. Your engine won’t start if your timing belt breaks.
You might observe one or more of the following if your timing belt is broken or worn out:
- the engine’s smoke
- engine stalls
- Rumbling or rough idling coming from the engine
- damaged pistons or valves
- lower oil pressure
Timing Belt Repair & Quality Auto Repair in Wilmington, NC
It is best to have a qualified, quality auto repair technician evaluate your car as soon as possible if you have encountered one or more of the aforementioned symptoms. Expect to pay between $300 and $500 for the service if your timing belt needs to be replaced. Many automobiles’ timing belts require some disassembly and reassembly since they are not always easily accessible. Smaller engines in economy cars result in less work. However, larger trucks, SUVs, or premium cars can take a lot longer.