If the problem or code that caused your Toyota Venza’s check engine light to come on is fixed, it will typically turn off by itself. For instance, if a loose gas cap was the reason your check engine light came on, the light will automatically switch off once the gas cap is tightened.
In This Article...
What does a Toyota Venza’s maintenance need mean?
You may reset the Toyota Venza’s maintenance required light using the instructions in this article. For a Toyota Venza of the first generation, the process is the same (20092015).
The “maint reqd” light on the Toyota Venza simply indicates that a service interval has been reached. The need for new engine oil follows from this. 5,000 miles after the last reset, it turns on.
This light only turns on as a result of those miles; it has no means of knowing if your oil has been changed or not since then, and it never, ever indicates a problem. so that when it appears on your dashboard, your heart doesn’t slightly skip a beat.
How can the TPMS light on a 2009 Toyota Venza be reset?
Turn the key to the “on” position with the car off, but don’t let it run. When the Toyota tire pressure sensor blinks three times, hold down the TPMS reset button until it stops blinking. Start the car, then let it run for 20 minutes to let the sensor reset. Under the steering wheel is typically where you’ll find the TPMS reset button.
How can my Toyota maintenance be reset?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
How can I turn off the Toyota maintenance is required light?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
How is the oil change light reset?
Reset Oil Change Indicator
- Turn on the ignition.
- Both the stop and accelerator pedals should be fully depressed.
- Maintain firm pressure on the brake and accelerator pedals.
- A notice verifying the reset process is ongoing appears after three seconds.
Why does my maintenance light come on after I change the oil?
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- The ODO display will briefly flash before beginning to display only zeros.
- Now the light will read “MAINT REQD.”
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Press and hold the ODO reset / readout button while the engine is off.
- If the car is on, turn it off.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
My maintenance is necessary light is on, why?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.
How do I stop the needed maintenance?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
C1201:
The two P0 codes indicate that the emissions system has a leak. Technically, it might be in the charcoal canister or filler neck, but most of the time it’s just a leaky gas cap. Either a worn-out cap or one that was put incorrectly.
The car is instructed to switch on the check engine light and turn off the traction and VSC by the C1201 code. In essence, this code is responsible for alerting you to an issue when the other two appear. Since they are the ones that created it, fixing the other codes should also repair this one.
When should my Toyota Venza get its oil changed?
For traditional oil, Toyota suggests changing your Toyota Venza’s oil and filter every 3,000 to 5,000 miles. Generally speaking, synthetic oil needs to be changed every 7,500 to 10,000 miles.
Toyota, does it need synthetic oil?
Only Solution. Only Toyota cars (apart from 3UR-FBE Engines*) that require 0w-20 synthetic oil have been given the go-ahead for longer oil change intervals of 10,000 miles or 12 months. (You should, though, keep checking the oil level frequently and topping off as necessary.