You must locate the oil option in the setting menu of the 2008 Toyota Highlander in order to reset the oil light. Hit the reset button at the bottom of the page. However, the light will continue to come on if you have low oil or need to change it. Prior to changing the oil in your automobile, you should make sure it has been parked and turned off for a few hours. Otherwise, you risk burning yourself on the hot oil in the automobile. Look for the oil pan in the engine area, and look underneath for the drain plug. Place a bucket underneath the plug, then take it out. As a result, the oil will be able to drip into the pan. Allow it to continue doing this for about an hour or until the dripping stops. Put the drain cap back on after it stops dripping, then look for the intake port on the top of the oil pan. Fill the oil pan completely using a funnel, being careful not to overfill it. It’s okay to go just a bit under, but going over can result in leaks and oil burnoff. Once it is filled, shut off the port, clean up any spilled oil, and you are done.
Turn the key to the on position without starting the car in a 2008 Toyota Highlander to reset the oil light. Up until trip a, keep pressing the trip button. and remove the key. Once it is turned off, turn the key back to the on position while pressing and holding the reset button. Until it is finished, the display will show it resetting.
In This Article...
How can you turn a Toyota Highlander’s oil light back on?
Turn the ignition to position one after inserting your key (the first setting before actually starting the car). Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for another 10 seconds or so.
How can you turn a Toyota’s maintenance needed light back on?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
How can I dim the maintenance is necessary light?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
How is the oil change light reset?
Reset Oil Change Indicator
- Turn on the ignition.
- Both the stop and accelerator pedals should be fully depressed.
- Maintain firm pressure on the brake and accelerator pedals.
- A notice verifying the reset process is ongoing appears after three seconds.
What type of oil is recommended for a 2008 Toyota Highlander?
High Mileage 5W-20 Full Synthetic Motor Oil, 5 Quart, from Mobil 1 (Part No. 120768) Product attributes: For engines with more than 75,000 miles, Mobil 1 High Mileage full-synthetic motor oil 5W-20 is made to allow up to 10,000 miles between oil changes.
Exactly how much oil does a 2008 Toyota Highlander require?
This oil lasts 15,000 miles even under harsh conditions (constant towing, hauling, idling, or dusty environment). Don’t forget to get our fantastic oil filter to keep junk out of your engine! with 5 liters of filter Check the oil level after refueling.
Why, after an oil change, is my maintenance required light still on?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
Why does my car indicate maintenance is needed following an oil change?
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Press and hold the ODO reset / readout button while the engine is off.
- Now the light will read “MAINT REQD.”
- The ODO display will briefly flash before beginning to display only zeros.
- If the car is on, turn it off.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
What does the 2008 Toyota Tundra’s maintenance required light mean?
Every 5,000 miles, the “Maintenance Required” oil change indicator light on the Toyota Tundra will come on. This maintenance light is merely a simple reminder that it’s probably time for an oil change at your neighborhood Toyota Service Center, not an emergency. When you’ve traveled 5,000 miles since the last time you reset your odometer, this maintenance light will automatically come on in your instrument cluster. This indicator is present in every second-generation Toyota Tundra pickup vehicle, so whether you own a new or used Toyota Tundra, you will probably notice it occasionally.