A Toyota Prius’ maintenance light can be reset easily and quickly in a matter of minutes. Start by parking the car and closing all of the doors. Don’t start the engine while turning the ignition key to the ON position. If your ignition is a push button, you must press the start/stop button twice without applying the brake. To access the settings menu, use the arrow navigation buttons in the left cluster of steering wheel controls. Select OK once you’ve navigated to the menu for the car settings. Select MAINTENANCE SYSTEM, then hit OK. Look for OIL MAINTENANCE on that menu, then hit OK once again. When a confirmation notice appears, choose YES, and then click OK. To confirm that the reset has been retained, turn off the ignition and then start the car.
Toyota Priuses’ “maintenance required” light can be reset by pressing the power button twice, the odometer button, which is located below the multifunction display, once to turn the vehicle off, the odometer button, while holding it down, and the power button twice (2 times), all while keeping your foot off the brake. Hold the odometer button down while you wait for the flashing dashes to stop and the reading to return.
For a 2014 Prius, turn the trip odometer to “trip A,” start the vehicle, push and hold the MPH/KMH button, turn the ignition off while holding the button, turn the ignition back on while holding the button, and watch the reset take place.
Thank you for your clear instructions; I was able to accomplish what the Toyota Service Department failed to do.
In This Article...
On a 2010 Prius, how do you reset the oil maintenance light?
If you often perform maintenance on your 2010 Toyota Prius, the tiny maintenance required light might become very aggravating. It will only take a few minutes to correct, though, and is extremely simple. Follow these steps to reset the oil maintenance light on a 2010 Toyota Prius:
- Press the push-button start once to turn the car off.
- The primary display should turn on in the center of the dashboard.
- To get to Trip A, push the Trip button on the steering wheel.
- Resetting oil maintenance data should be visible on the display.
- As you double-tap the start button, keep your foot off the brake.
- While pushing the push-button start twice, press and hold the mph button that is immediately above it.
It’s best to get regular oil changes to keep your Prius in good condition. You may also reset the maintenance light in a matter of minutes. But did you know that by downloading the Jerry app and comparing prices, you can also save hundreds on auto insurance in only a few minutes?
Jerry is a certified insurance broker who offers estimates from numerous reputable and highly rated auto insurance providers. Jerry can assist you in purchasing insurance and terminating your current policy after you discover a fantastic cost for your Toyota Prius. Customers often save close to $900 annually!
How can the maintenance needed light on a 2010 Toyota be reset?
How Can the Maintenance Required Light Be Reset?
- Turn on your car. Look at your dashboard when your key is in the on position.
- Press the Trip Meter Reset Button after turning off the engine.
- Re-start the vehicle.
- Keep pressing the reset button.
- Reset button released
How can I turn off the Toyota maintenance is required light?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
How can I dim the maintenance is necessary light?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
Why does my maintenance light come on after I change the oil?
- Press and hold the ODO reset / readout button while the engine is off.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Now the light will read “MAINT REQD.”
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- If the car is on, turn it off.
- The ODO display will briefly flash before beginning to display only zeros.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
When your maintenance light illuminates, what should you do?
Simply put, the flashing maintenance required light is alerting you that maintenance on your car is necessary. The indicator will come on when a predetermined period of time has passed since your car’s last service or based on how far you’ve driven it.
This light typically indicates that you should change the oil in your car. The maintenance data will be reset for you when your car has been taken in for service.
To manually reset the system to turn off the light, however, follow these instructions:
When the maintenance light comes on, you can continue to drive, but bear in mind that you are doing so at your own risk if the required or scheduled repair is skipped.