For your information, this operation is for the Toyota Sequoia’s second generation (2008, 2009, 2010, 2011, 2012, 2013, 2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022 model years).
In This Article...
Sequoia
We are currently driving an old Toyota Sequoia, and the annoying maintenance required light is constantly on. The first action you take to get rid of that is:
- Start your vehicle
- Project the TRIP A screen.
Then, using the ODO/TRIP button on the dash, make sure the TRIP A is set to your mileage screen.
- Deactivate the ignition.
- Turn the ignition on while maintaining pressure on the ODO/TRIP button.
Holding down the ODO/TRIP button now will prevent the engine from starting; instead, we’ll simply click it back to the on position.
Hold the button down further.
Maintaining pressure on the button will cause it to perform a small four-dot dance, after which our maintenance is required light will turn off.
Sequoia
- You’ll be prompted with a reset maintenance question. You will now have 5,000 miles until your next service because the answer is YES.
- start the vehicle
- Click the middle button to confirm.
- Once there, you must access the VEHICLE SETTINGS.
- Then I’ll move to the right, but you can also move to the left; both actions will bring up the SETTINGS or the small gear that is located at the top.
- Clear any message on the dashboard by using the back button.
- Then, scroll down to the very last choice and choose MAINTENANCE RESET.
Okay, the light has been reset. Would you mind sharing this article or leaving me a comment if it was helpful? Please give me a favorable review, and I hope to run into you again. Have a wonderful day, and thanks again for your time.
How can you turn a 2011 Toyota’s maintenance light back on?
Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for a further 10 seconds. You can hear a beeping noise in addition to the maintenance light beginning to flash. The light ought should thereafter go out.
How can the oil light on a 2008 Toyota Sequoia be reset?
- Make sure the tripmeter is lit up on the vehicle’s odometer when the ignition is in the ON position, then switch it to the OFF position.
- Press and hold the MODE or TRIP reset button.
- Switch the ignition to the ON position while holding the reset button.
**To activate the Key On/Engine Off mode using the Engine Start/Stop button, depress the button twice while keeping your foot off the brake pedal.
- Hold the reset button down until the odometer shows “000000 is shown before the initial value.
- Ensure the reset was acknowledged by turning the vehicle on and off again.
- Press SETUP on the navigation screen.
- Press VEHICLE, then MAINTENANCE after that.
- To reset an item, touch the desired item (i.e. Engine Oil, Oil Filter, Tire Rotation, etc.)
- Fill in the necessary fields with the new information after this “Following Service period (i.e. date and distance till next service is due)
- Click OK when finished.
- Steps 3-5 must be repeated for any additional services rendered.
- Make that the odometer is shown with the ignition switch in the ON position, then switch it to the OFF position.
- Hold the reset button down until the odometer shows “the MAINT REQD light flashes, or 000000
- You can press INFO or SETUP on the navigation screen.
- Next click MAINTENANCE.
- Fill up the necessary fields with the new information after this “Next Service Interval (i.e., the day or time till the next service is due)
These reset instructions should be useful to you, we hope. With our mobile app Oil Reset Pro, which is available in the Apple and Google Play stores, you can always have this method at your fingertips along with the rest of the domestic, Asian, and European manual maintenance reset procedures. To get a free download from the shop right away, click the links below.
How can I turn off the Toyota maintenance is required light?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
Why does my maintenance light come on after I change the oil?
- If the car is on, turn it off.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Press and hold the ODO reset / readout button while the engine is off.
- Now the light will read “MAINT REQD.”
- The ODO display will briefly flash before beginning to display only zeros.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
What does it imply if your Toyota has a maintenance required light on?
On your dashboard, the Toyota maintenance light may read “MAINT REQD. It’s a light that is always on and alerts you when you require an oil change at a licensed auto shop. Your Toyota will run more smoothly and efficiently if you change the oil in your car.
How can the maintenance needed light on a 2013 Toyota Tundra be reset?
- Without starting the engine, turn the ignition to the “On position. If your car has a push-button ignition, press “Start” without depressing the brake pedal.
- By pushing the display change button or “Trip button,” you can change the display to “Trip A.”
- Completely shut off the car.
- Keep holding down the “Trip button.”
- Hold the “Trip button down while turning the ignition to “On without starting the car.
- Release the “Trip button” whenever the trip meter reads “all zeros.”
How can I turn off the Toyota Tacoma’s maintenance is required light?
The convenience of having a car-savvy family member must be incredible! Yes, you can manually reset your light as you are aware that your car is in good condition.
Turn off your vehicle, then push and hold the odometer reset button to turn off the maintenance light on a Toyota Tacoma. Odo/Trip is the typical label for this button. Hold the button down as you restart the ignition of your car.
Your maintenance light ought to be back on now! By starting your car as usual and waiting a few seconds, you can ensure that the light remains off. Visit a professional to ensure that your automobile and your sensors are in good working order if the light does indeed come back on.
Although automobile repairs might be expensive, Jerry can help you save money on other auto-related costs. Jerry is a free insurance comparison software that checks around for the best deals with more than 50 different insurance providers. You may make adjustments at any time, receive prices instantly, and text an agent with any queries you may have. Every year, the typical Jerry user saves $879.
What distinguishes a maintenance requirement from a check engine light?
Many people are unsure of what each of these lights means, and the check engine light and the service engine soon light are frequently confused for one another. We’ll describe how distinct they actually are despite the fact that they appear to be similar.
Authored by: Bradley Hayes, Director of Marketing at Autoscope European Car Repair and Automotive Blogger
Since Karl Benz originally unveiled his Benz Patent Motorwagen, automotive technology has advanced significantly. In fact, the notion that computers are essentially controlling our cars in today’s computer-driven society shouldn’t be shocking. In order to assure the precise right operation of your vehicle’s numerous systems and components, they regulate and track their performance. They even notify the driver when the automobile needs repair or maintenance. While technology hasn’t yet given our cars voices (like Kitt from Knight Rider), it has made it possible for them to communicate in other ways, such as through a series of backlit symbols that show up in your instrument cluster, such as a “check engine” and a “service engine” light.
My maintenance is necessary light is on, why?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.
What does a maintenance required light that blinks mean?
If you’re unsure of what a warning light on your dashboard indicates, it can make you feel uneasy. Thankfully, you normally don’t need to worry about it.
A flashing maintenance light is typically your car’s method of telling you that it needs to be serviced soon. The light’s purpose is to alert drivers when it might be time for an oil change or a tune-up by turning on at predetermined intervals.
You have roughly 500 miles left before you need to have your automobile serviced when the light first starts flashing. Your maintenance light will inform you by turning on and staying on when it’s due for service.
Download Jerry, the super insurance expert app, to find the answers to all of your maintenance-related concerns.
Jerry is a powerful tool for finding vehicle insurance discounts, and it can do so in just 45 seconds! Jerry will evaluate prices from the leading insurance companies in the country to get you the cheapest offers, and if you decide to transfer, he can even cancel your current policy!