You must start the engine and hold down the disp or trip button until the panel reads trip A in order to reset the oil life indicator on your 2017 Toyota RAV4. When you get there, you can turn the ignition to the lock position, but you shouldn’t start the engine. Now turn the key to the OFF position while maintaining pressure on the trip button. Finally, you must release the button while turning the key back to the lock position. Your indicator should now indicate “0 miles,” and you can resume using your car normally.
You may turn off the oil light on your Toyota Highlander by following these instructions: Don’t start the engine after turning the ignition switch to the “on” position. If your vehicle has a start push button, press it without depressing the brake pedal. To see “trip a,” briefly click the odometer knob. To start, turn the ignition switch to the “on” position, then click and hold the “reset trip odometer” button. Hold down the reset trip odometer button until “000000” miles appear on the indicator and the maintenance light goes out.
In This Article...
On a RAV4, how do you erase the maintenance message?
How to Extinguish the Toyota RAV4’s Maintenance Light
- Put the ignition on with your key. Turn the key to the first position.
- On the dashboard, press the reset trip meter button. Hold it down for a couple of seconds.
- Hold the odometer button down for another five or so seconds.
- Release the odometer button after it is off.
How do I remove the warning about Toyota maintenance?
Turn your key to the second position after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a total of 10 seconds. The light ought to flash, potentially beep, and then go off as a result. Release the odometer button once it has been turned off, then start the automobile.
Why does my Rav4 indicate that maintenance is needed?
The significance of the emblem MAINT REQD is significant. The MAINT REQD light indicates when the vehicle’s scheduled maintenance is due when it illuminates. If your car is under two years old, this service can be covered by your ToyotaCare plan.
Why does my Toyota state it needs maintenance?
- Now the light will read “MAINT REQD.”
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- If the car is on, turn it off.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- The ODO display will briefly flash before beginning to display only zeros.
- Press and hold the ODO reset / readout button while the engine is off.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
Why, after an oil change, is my maintenance required light still on?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
How should I respond if my maintenance light illuminates?
How Can the Maintenance Required Light Be Reset?
- Turn on your car. Look at your dashboard when your key is in the on position.
- Press the Trip Meter Reset Button after turning off the engine.
- Re-start the vehicle.
- Keep pressing the reset button.
- Reset button released
The maintenance is needed light is on why?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.