Toyota Highlander Maintenance Light Reset Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for another 10 seconds or so. You can hear a beeping noise in addition to the maintenance light beginning to flash. The light ought should thereafter go out.
In This Article...
What does the Toyota Highlander’s maintenance required light mean?
Simply put, the flashing maintenance required light is alerting you that maintenance on your car is necessary. The indicator will come on when a predetermined period of time has passed since your car’s last service or based on how far you’ve driven it.
This light typically indicates that you should change the oil in your car. The maintenance data will be reset for you when your car has been taken in for service.
To manually reset the system to turn off the light, however, follow these instructions:
When the maintenance light comes on, you can continue to drive, but bear in mind that you are doing so at your own risk if the required or scheduled repair is skipped.
How can the maintenance needed light be turned off on a 2011 Toyota Avalon?
1. Switch on the engine (one position before starting engine).
2. Verify the displayed odometer reading. Turn off the ignition.
vehicle keyless entry systems:
3.Press “ENGINE START STOP” switch to IGNITION ON mode while pushing the trip meter reset button. Hold down the button while continuing to press it until “000000” appears on the trip meter.
Automobiles without a smart key system:
3.Start the ignition while pressing the trip meter reset button (one position before starting engine). Hold down the button while continuing to press it until “000000” appears on the trip meter.
4. To make sure the indicator has been reset, turn off the ignition and start the engine.
How can my Toyota maintenance be reset?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
Why does my maintenance light come on after I change the oil?
- Now the light will read “MAINT REQD.”
- Press and hold the ODO reset / readout button while the engine is off.
- The ODO display will briefly flash before beginning to display only zeros.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- If the car is on, turn it off.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
When I turn on my automobile, why does the maintenance required light flash?
If you’re unsure of what a warning light on your dashboard indicates, it can make you feel uneasy. Thankfully, you normally don’t need to worry about it.
A flashing maintenance light is typically your car’s method of telling you that it needs to be serviced soon. The light’s purpose is to alert drivers when it might be time for an oil change or a tune-up by turning on at predetermined intervals.
You have roughly 500 miles left before you need to have your automobile serviced when the light first starts flashing. Your maintenance light will inform you by turning on and staying on when it’s due for service.
Download Jerry, the super insurance expert app, to find the answers to all of your maintenance-related concerns.
Jerry is a powerful tool for finding vehicle insurance discounts, and it can do so in just 45 seconds! Jerry will evaluate prices from the leading insurance companies in the country to get you the cheapest offers, and if you decide to transfer, he can even cancel your current policy!
On a 2013 Toyota Tundra, how do you turn the maintenance light back on?
- Without starting the engine, turn the ignition to the “On position. If your car has a push-button ignition, press “Start” without depressing the brake pedal.
- By pushing the display change button or “Trip button,” you can change the display to “Trip A.”
- Completely shut off the car.
- Keep holding down the “Trip button.”
- Hold the “Trip button down while turning the ignition to “On without starting the car.
- Release the “Trip button” whenever the trip meter reads “all zeros.”
How can I turn my car’s service light back on?
First, turn on the engine. Step 2: The display will say “Service required” if a service is overdue. Locate and press the OK button at the top right of the steering wheel for longer than one second to clear this message. The service interval will be reset to its default value in Step 3.