automobiles without a smart key system
1. Switch on the engine (one position before starting engine).
2. Verify the trip meter Readings are displayed. Switch off the ignition.
3. Set the ignition to run while maintaining pressure on the trip meter reset knob (one position before starting engine).
4. Keep the knob depressed for at least 5 seconds. “000000” appears on the odometer, and the light turns off. The LED will keep blinking if the system can’t be reset.
5. To make sure the indication has been reset, turn off the ignition and then turn on the engine.
1. Slightly depress the “ENGINE START STOP” switch (do not start engine).
3. Press the “ENGINE START STOP” switch once while simultaneously pressing the Trip Meter reset button (do not start engine).
4. Hold down the button while continuing to press it until the trip meter reads “000000” or, if equipped, “COMPLETE.”
In This Article...
How can I turn my Toyota Sienna’s maintenance required light back on?
In many vehicles, persistent maintenance lights are a regular problem. Typically, there is no electrical issue; instead, your mechanic just neglected to reset the alert after your service was finished.
Just adhere to these simple steps to reset the maintenance required light on your Toyota Sienna:
- Put your ignition key in accessory mode. You shouldn’t start your engine.
- Find the ODO/TRIP button and press it until ODO appears on the display.
- OFFSET your Sienna.
- As you continue to hold down the ODO/TRIP button, turn on your car.
- You have reset the maintenance light when the odometer display shows just zeros.
- Once more, turn off your car.
Your car is not in need of maintenance, so you can drive with a little more confidence now that the maintenance light is off. Check out the Jerry app to see how much you could be saving on auto insurance before you get back on the road.
After you download Jerry, all you need to do is respond to a few questions that will take you around 45 seconds to do, and you’ll get car insurance rates for coverage that is identical to your current plan right away. Customers of Jerry save $879 year on average.
On a 2013 Toyota Sienna, how do you turn the maintenance light back on?
Absolutely! By doing the following, you can turn off the maintenance light on your 2013 Toyota Sienna:
- Ensure that Trip A is selected on your odometer.
- Turn off your vehicle.
- To reset the odometer, press and hold the button. On your dashboard, next to the speedometer, is the button.
- Turn on your car while holding down the button.
- Press the button again after your trip. The mileage on a car is 0.
- Press the button again to turn off your car.
- The maintenance light ought to be off the next time you start your car!
Why not spend a little more time learning about your alternatives for auto insurance while you’re taking the time to reset your maintenance light? With the Jerry app, it’s simple. To receive a comprehensive list of quotations for policies identical to your current one, simply download the app and respond to a few brief questions. The typical user saves $879 yearly!
On a 2015 Toyota Sienna, how do you turn the maintenance light back on?
If mechanics neglect to reset the maintenance alert after servicing the car, it may become an annoyance. Fortunately, a 2015 Toyota Sienna’s maintenance light is simple to reset.
Simply adhere to these guidelines to restart the light:
- Shut down the van.
- The maintenance is necessary light needs to be reset.
- A key is turned to the on position. Alternatively, if your vehicle has a push-button start, you can depress the button twice while keeping your foot off the brake.
- To get the Trip A reading, press the trip odometer button on the instrument cluster.
- In addition to pressing and holding the trip odometer button, restart the engine of the car.
You obviously care about your automobile if you take such good care of your Sienna. Therefore, make sure your car is fully insured without paying too much. It is quick and simple with the Jerry app.
Jerry is a certified insurance broker who obtains rates from numerous reputable and highly rated auto insurance providers. Jerry can assist you in purchasing insurance and terminating your current policy after you discover a fantastic quote for your 2015 Toyota Sienna. Customers often save close to $900 annually!
Why does my maintenance light come on after I change the oil?
- Now the light will read “MAINT REQD.”
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Press and hold the ODO reset / readout button while the engine is off.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- If the car is on, turn it off.
- The ODO display will briefly flash before beginning to display only zeros.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
My maintenance is necessary light is on, why?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.
How can you turn a Toyota’s dash light back on?
Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off. Start the vehicle after releasing the odometer button.
How can the odometer on a Toyota Sienna be reset?
The navigation controls on the right instrument cluster of the steering wheel and the center-mounted display can be used to reset the most recent Toyota Sienna maintenance necessary light. The fourth generation is a brand-new model, thus it undoubtedly has a lengthy warranty period with lots of fine print content. Even though it might seem insignificant, resetting the maintenance light could violate the warranty, so check with the dealership or a licensed mechanic before doing so.
- Without starting the engine, turn the ignition to “On.”
- Hold off until the Sienna logo vanishes from the dashboard screen.
- Use the steering-wheel-mounted controls to cycle through the settings until you come across Maintenance Reset.
- By pushing the center button on the navigation controls, choose the menu. The back button can be used to return to the menu choices if you accidentally click on the incorrect option.
- In order to effectively reset the maintenance light, choose Yes when prompted by the menu.