1. Switch on the engine (one position before starting engine).
2. Verify the trip meter Readings are displayed. Switch off the ignition. Go to step three.
1. Slightly depress the “ENGINE START STOP” switch (do not start engine).
2. Verify the trip meter Readings are displayed. Switch off the ignition.
3. Press the “ENGINE START STOP” switch once while simultaneously pressing the Trip Meter reset button (do not start engine).
In the absence of a multiinformation display: Press and hold the button continuously until the trip meter reads “000000.”
4. To make sure the indicator has been reset, turn off the ignition and start the engine.
1. To change the display to SETTINGS while the engine is running, use the controls on the right side of the steering wheel.
2. From the SETTINGS menu, choose MAINTENANCE SYSTEM.
3. To reset the system, choose YES.
4. “Initilization Completed” will be shown when the reset is finished.
In This Article...
How can the repair needed light on a Toyota Highlander be reset?
Toyota Highlander Maintenance Light Reset Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for another 10 seconds or so. You can hear a beeping noise in addition to the maintenance light beginning to flash. The light ought should thereafter go out.
How can you turn a Toyota’s maintenance needed light back on?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
How can the maintenance needed light be turned off on a 2016 Toyota Camry?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
Why does my maintenance light come on after I change the oil?
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- If the car is on, turn it off.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- Press and hold the ODO reset / readout button while the engine is off.
- Now the light will read “MAINT REQD.”
- The ODO display will briefly flash before beginning to display only zeros.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
What does the triangle in a Toyota Highlander with the exclamation point mean?
Have you ever been operating your Toyota Highlander when a symbol suddenly appeared on the dashboard? If so, then every sign has a unique meaning. Everybody occasionally gets a visit from a dashboard light.
While some lights are only indicators, others are alarms indicating your Highlander requires regular upkeep or repairs. It’s crucial to understand what each dashboard light on your vehicle indicates.
An indication light is any light that appears on the Toyota Highlander’s dashboard and is either blue or green. A light that alerts you that anything in your car is on is what an indicator light does exactly as it sounds. The majority of the time, it indicates on your dashboard whether a Highlander feature has been activated or canceled.
Some of the typical warning lights that you might see are listed below:
- An icon resembling a speedometer serves as a visual cue that the cruise control system is engaged.
- The VSC/TRAC OFF Indicator shows whether the traction control or vehicle stability control systems are activated or off. To turn off the light, push and hold the switch while the car is still moving.
- Headlight High Beam Indicator: This blue light signifies the active state of the headlight high beams.
- Turn Signal Indicator: These green lights signify that the Highlander’s right or left turn signal has been engaged.
- An emblem in the shape of a key will display on your Toyota Highlander’s dashboard to let you know that the security system is operating as intended.
- TRAC OFF Indicator: This light appears to alert you to the need to turn off the vehicle’s traction control and/or stability control systems.
Your Toyota Highlander will have a warning light if it has a yellow or red light. A warning light is typically an issue that needs to be resolved right away in order to keep your SUV in the finest condition possible. If you notice any of the lights listed below, get in touch with our service staff to arrange a visit:
- When an icon resembling an old-fashioned oil can appears, it means your oil pressure is too low and should be checked. Low Engine Oil Pressure Warning Light: You should take immediate action to address this problem in order to prevent potential engine damage.
- Electric Power Steering (EPS) Warning Light: It’s critical to have your Highlander evaluated if this warning light, which looks like a steering wheel next to an exclamation point, comes on your dashboard.
- Master Warning Light: When the master warning system detects a problem, a triangle with an exclamation point inside of it shows on the dashboard and a buzzer sounds.
My maintenance is necessary light is on, why?
The mileage is the only factor that activates the maintenance required light, also known as the service required light. When this light turns on, different automakers have varying standards. For instance, the maintenance needed light on a car might turn on once every 10,000 lights and stay lit until it is manually turned off.
The oil change, spark plug replacement, new tire, etc. are just a few examples of the routine maintenance that should be performed on a vehicle.
When servicing your vehicle, mechanics typically reset the maintenance required light. The process for resetting the maintenance required light differs based on the make and type of the car, yet, if they don’t, you can do it yourself.
What does it imply if your Toyota has a maintenance required light on?
On your dashboard, the Toyota maintenance light may read “MAINT REQD. It’s a light that is always on and alerts you when you require an oil change at a licensed auto shop. Your Toyota will run more smoothly and efficiently if you change the oil in your car.
What distinguishes a maintenance requirement from a check engine light?
Many people are unsure of what each of these lights means, and the check engine light and the service engine soon light are frequently confused for one another. We’ll describe how distinct they actually are despite the fact that they appear to be similar.
Authored by: Bradley Hayes, Director of Marketing at Autoscope European Car Repair and Automotive Blogger
Since Karl Benz originally unveiled his Benz Patent Motorwagen, automotive technology has advanced significantly. In fact, the notion that computers are essentially controlling our cars in today’s computer-driven society shouldn’t be shocking. In order to assure the precise right operation of your vehicle’s numerous systems and components, they regulate and track their performance. They even notify the driver when the automobile needs repair or maintenance. While technology hasn’t yet given our cars voices (like Kitt from Knight Rider), it has made it possible for them to communicate in other ways, such as through a series of backlit symbols that show up in your instrument cluster, such as a “check engine” and a “service engine” light.