How To Reset 2014 Toyota Corolla Radio

Toyota / By

Press and hold the Audio system power button for 3 seconds to reset the radio in your 2014 Toyota Corolla. You will then be prompted with an option and asked if you want to restart the computer. The driver frequently complains about the radio randomly rebooting, freezing, having problems with Bluetooth connectivity, or having a touch screen that is unresponsive. In certain cases, updating the radio software on your Toyota at the dealer will resolve this well-known problem. In some circumstances, assembly is necessary while changing the radio. If you need to replace your radio, there are several aftermarket radios with extra features that would be a terrific upgrade.

Your 2014 Toyota Corolla’s radio can be reset by unplugging and replugging the battery. A firmware upgrade might be necessary if your radio gets stuck during the rebooting process. Consult the dealer in your area.

You’ll need a wrench and a set of pry tools to remove the radio from a 2014 Toyota Corolla. Start by removing any screws that are holding the dash on where you can. It should pop off. There are a few bolts holding the radio in place once the dash has been unbolted. Take those out, then advance the radio. You will need to cut the cables because it will be hooked in. Reinstall the bolts, attach the dash, and connect the new radio at this point.

Soft Reset

The Toyota Entune multimedia system can be quickly and easily reset using the following technique:

  • Put your key in the ignition lock and turn it to the “On” position, or start the engine by pressing the Engine button twice.
  • Hold off till the multimedia screen turns on.
  • For 12 seconds, firmly press and hold the PWR-VOL knob.
  • Toyota Entune ought should restart and work normally.

Before moving on to more advanced techniques that will also remove part of your data, it is usually worthwhile to try this method first, even though it doesn’t always succeed. Alternately, attempt these:

  • While the engine is off, turn on the electrical systems.
  • Hold off till the Entune system turns on.
  • Take your phone, then un-sync Toyota with all of your other Bluetooth devices.
  • Go to Bluetooth connections on the Entune screen and take your phone out of the list of recognized devices.

Hard Reset

If the prior approach didn’t work, you must carry out the following actions:

  • Do not start the engine; instead, press the Engine button twice.
  • The multimedia system’s physical Apps button should be pressed and held. Turn the lights on and off three times without letting go. On the screen will come a selection called Diagnosis Check.
  • The screen’s INIT button should be pressed and held. You will receive a “Personal data is initialized” notification. OK? which will elicit a “Yes” from you.
  • Check to see whether all Bluetooth connections, radio stations, and phone calls have been disconnected before starting the engine.

The most effective way to guarantee a long-term, bug-free operation is to use this procedure, which wipes out all of the saved data and effectively returns Entune to factory default condition.

Software Reset

Using software commands solely is an alternative to the hard reset technique. Additionally, this may delete your data, so proceed with caution and back up any crucial information.

  • Without starting the engine, start the vehicle.
  • Remove Entune from any Bluetooth devices that are currently in use.
  • Similar to the first way, press and hold the PWR-VOL button for roughly 12 seconds.
  • Select the Setup menu on the display after the restart is finished.
  • Choose General from the menu.
  • Locate and click the Delete Personal Data button.
  • Check that everything is working properly by starting the car.

Without the code, how can I reset my Toyota radio?

For 4050 seconds, hold down the Power/Volume button. In less than a minute, your radio ought to be unlocked. Approach 2:

  • Start the engine.
  • If CODE appears on the screen, turn off the radio.
  • Holding Down and the Power Button for 60 seconds will work.
  • You should have access to both radio and music without having to use the radio.

How can I restart the audio system in my car?

Your radio is locked if the CODE display is shown. If the car has just undergone maintenance, had other settings restored, or had the battery replaced, this is a typical occurrence.

You’ll need to enter a code to go beyond the car’s security system in order to open the radio. This code can be found in several places, most notably:

  • Find out whether your nearby dealership can give you the code or unlock it for you by going there.
  • Look for a database of stereo security codes on the manufacturer’s website.
  • in the owner’s guide. Look in the radio/stereo or security sections of the owner’s manual to find the code right away.

The following measures should be used if you are unable to locate the code and the dealership or installation facility was unsuccessful in unlocking it:

  • To reset the radio, press and hold the power button for a few minutes.
  • Just turn the ignition on, not the engine
  • Turn off the radio.

If this doesn’t work right away, hold the power button down for a longer period of time or simultaneously press the power and seek buttons. Hopefully, one of these techniques will get you jamming out once more right away!

Review your your insurance coverage and download the Jerry app while you wait for a technician to unlock your audio. Jerry is the quickest and best way to locate a car insurance plan that is specially tailored for you.

Jerry will handle the phone calls, paperwork, and renewals for your top choice after giving you a thorough cross-analysis of the best plans across providers so that you won’t have to. Even your old policy is cancelled!

How do I update the software on my Toyota 2014?

Updates for Toyota Entune

  • Open the EntuneTM app, then establish a Bluetooth or USB connection with your car.
  • You’ll see a menu on the screen that gives you the option of updating “NOW” or “LATER.”
  • The “NOW” option handles all of your updates instantly and automatically.

How can the Bluetooth on a 2014 Toyota Corolla be reset?

It can be challenging to pair your phone with the Bluetooth in a Toyota Corolla, and you can discover that after turning on your Toyota, your phone is not displayed on the multimedia screen or that your phone notifications do not appear on the Toyota Entune screen. We’ve listed some problems and remedies below if you’re seeking for Toyota Bluetooth troubleshooting:

There are a number of reasons why your phone could not show up on the multimedia screen in your Toyota. Here are the steps for each:

  • The Bluetooth setting in the car might not be on. Go to the menu, setup, Bluetooth, detailed options, and make sure Bluetooth power is on to check this feature.
  • Ensure that Bluetooth is enabled on your phone. You may do this in the settings of your phone.
  • A new Bluetooth connection won’t be formed if your Toyota already has five devices registered. Check which devices are registered on your Toyota using the same procedures as before, and then unpair an old device before pairing a new one.
  • One of the connected devices can be set to be audio-only if there are two linked devices connected at once. Select “registered devices” from the Bluetooth menu to correct this. By clicking the corresponding button, you may choose which device you want to have enabled for phone or music settings.

If your phone and Toyota are properly paired but your Toyota is not notifying you of new messages or calls, take the following actions:

  • Check the permissions on your phone. Toyota Bluetooth issues are frequently brought on by the phone. Make sure that push notifications for calls and messages from your favourite app are turned on next to the name of your linked vehicle in your phone’s settings.

Resetting your phone or Entune system may be necessary if issues persist:

  • Turn your phone totally off for 30 seconds, then on again to reset it. Make sure you are truly turning off your phone as opposed to simply restarting it.
  • Press and hold the audio knob to turn off the system, and Entune will shut down and resume on its own. This will reset the Entune System.

How can I obtain the radio code for my Toyota?

Before removing the device from a car or truck or performing maintenance that calls for the battery to be unplugged, it is best to obtain a car radio security code. By employing this method, you can lessen the frustration of being locked out of your car audio and, depending on the radio’s manufacturer and where you are, possibly save money on radio unlocking.

Step 1Find the portion of your car’s owner’s manual that describes how to use the radio. The radio security code is frequently printed on the inner back cover of instruction books or in the stereo section.

Step 2Check the glove box of your car for a sticker or card with the radio code if the handbook is missing it. This is where the code will occasionally be placed by some automakers.

Step 3Removing the stereo and noting its serial number will allow you to contact the automaker for the security code. To accomplish this, start by taking off the faceplate that surrounds the car radio. This can be done for many car models by carefully pulling or prying the plate out with a flat tool or screwdriver. Depending on the model, the plate might also be held in place by clips or need to be removed by sliding it to the side or downward. To read the label generally found on top of the car radio, pull or slide it out just far enough. It will be possible to jot down the device’s serial and model numbers. Then, make a note of the car’s VIN (which may be found on the side of the driver’s-side door as well as the driver’s-side front window). Finally, use this information to contact the local car dealer’s service department or the manufacturer directly to get the security code for the vehicle. As an alternative, you can phone the radio manufacturer and provide the same information to receive the code.

How do I re-battery my radio?

If none of these guides proves successful for you, your last resort is to stop by a nearby car radio installation shop. Depending on the model of your radio, they might be able to unlock it.

You’ll recall that I said I’d demonstrate how to bypass automobile radio codes. This trick was something I recently discovered, therefore I choose to share it with you in this blog. This hack has been tested on Honda and Acura vehicles, and it is effective. The Acura ILX, Acura TLX, Acura RDX, Honda Pilot, Honda Civic, and Honda Accord are the specific models that this technique will work on. These automobiles must be 2010 model year or newer.

  • If CODE appears, turn on your audio system and check it. If it does, stop using it.
  • The radio power button should then be pressed and held down.
  • It must be held for around 40 to 50 minutes. Your automobile audio system will come on and bypass the code at this time.
  • Make sure your ignition is in the ON position if you want to bypass the radio security codes on these cars.

The makers of your cars don’t want you to know about this trick. Yes, I did precisely that. How to unlock the Ford radio without a code is a different hack I want to share with you. The above trick and this one are similar. On a Ford BA, I watched it operate. However, you can give it a shot on other Ford models to see how it turns out.

  • You must turn your ignition to the ON position in order to accomplish this.
  • For roughly 5060 minutes, press and hold both the SEEK and audio power buttons. Without requiring the radio code, it will then switch on.
  • Check to see if your radio shows CODE or LOC when it is turned on. Turn off the radio if it does.