1. Turn the ignition key to run or press the “ENGINE START STOP” switch once before starting the engine (one position before starting engine).
2. Verify the trip meter Readings are displayed. Switch off the ignition.
3. Start the ignition while continuing to depress the MPH or KM/H button (do not start engine).
4. Keep holding the button down until the trip meter reads “000000” and the display says the reset is finished.
5. To make sure the indication has been reset, turn off the ignition and then turn on the engine.
In This Article...
How can I turn off the Toyota maintenance is required light?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
On a 2010 Prius, how do you reset the oil maintenance light?
If you often perform maintenance on your 2010 Toyota Prius, the tiny maintenance required light might become very aggravating. It will only take a few minutes to correct, though, and is extremely simple. Follow these steps to reset the oil maintenance light on a 2010 Toyota Prius:
- While pushing the push-button start twice, press and hold the mph button that is immediately above it.
- Resetting oil maintenance data should be visible on the display.
- Press the push-button start once to turn the car off.
- As you double-tap the start button, keep your foot off the brake.
- The primary display should turn on in the center of the dashboard.
- To get to Trip A, push the Trip button on the steering wheel.
It’s best to get regular oil changes to keep your Prius in good condition. You may also reset the maintenance light in a matter of minutes. But did you know that by downloading the Jerry app and comparing prices, you can also save hundreds on auto insurance in only a few minutes?
Jerry is a certified insurance broker who offers estimates from numerous reputable and highly rated auto insurance providers. Jerry can assist you in purchasing insurance and terminating your current policy after you discover a fantastic cost for your Toyota Prius. Customers often save close to $900 annually!
Why, after an oil change, is my maintenance required light still on?
If your oil light continues to illuminate even after changing the oil in your engine, you should examine the sensor to rule out a faulty sensor as the root of the problem. The oil pump might become clogged with dirt and other debris, leading the sensor to mistakenly report oil problems. Although changing the sensor is pretty straightforward, you should take your car to a qualified mechanic if you don’t feel confident doing it yourself. Low oil pressure is the following typical reason. Your oil light will turn on if the oil pressure drops below 5 pounds per square inch. You should check the oil level even though this shouldn’t happen after an oil change because you never know.
Even after an oil change, the final common cause of a lit oil light is perhaps the most troublesome. Numerous engine problems might result from the oil pump not circulating enough oil to maintain the engine’s parts lubricated and operating as intended. Parts do wear down over time, even though getting oil changes at regular intervals should prevent this issue from happening.
Why does my car indicate maintenance is needed following an oil change?
- The ODO display will briefly flash before beginning to display only zeros.
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- If the car is on, turn it off.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- Now the light will read “MAINT REQD.”
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Press and hold the ODO reset / readout button while the engine is off.
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
Why is still on my maintenance light?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to push it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.
After an oil change, how do I turn off the maintenance light?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.