Make sure the tire pressures are accurate before resetting the system. After starting the car, hold down the reset button while doing so. On the instrument panel, it is located low and to the right of the steering wheel. Hold down the button until the instrument panel’s tpms indicator light blinks gently three times.
The 2010 Toyota Corolla’s reset button for the tire pressure light can be found on the instrument panel, within the glove compartment, or on the knee bolster. Hold on until there are three light flashes.
The best option is to have the shop remove the sensors the next time you buy tires and replace them with regular fill valves. Discover how to inspect your tires like your father did. has no expense at all
In all honesty, I own a 2010 Corolla and have been a licensed auto technician for 36 years. I am aware of Al’s concerns with the intermittent on-and-flashing of the tps light. If you give it some thought, the solution is actually rather straightforward! The first thing to note is that modern cars include a variety of control modules, each of which functions as the system’s brain. The computer or module is configured to keep all tires within 3-6 psi of the manufacture requirements, which are on your door jam. You also have sensors that feed that module or brain, providing information about how the system is operating and performing (drivers). As long as a pressure stays within the manufacturer’s specifications, the light on your dash won’t turn on. If it is too high or low, however, the sensors will transmit signals to the module, which will turn on the light. Now, if the light is constantly on, there may be a sensor or pressure problem. Now, if the light is always flashing, there is probably an issue with the computer or a module. If you visit a store and scan the module, it will provide the information you need. A DTC is a diagnostic problem code. The scanner will read the code and will immediately inform you of the precise problem with that d**n bulb! If you discover a DTC saved in the TPMs module, it will generally be code: C2141 the computer or module has a problem with that code.
In This Article...
How much pressure should the tires of a 2010 Toyota Corolla be?
You should use different tire pressures for the front and rear wheels of the Toyota Corolla. Utilize the following advice: 38 psi in the front tires. 36 psi in the rear tires.
In what location on a 2010 Toyota Corolla is the TPMS button?
Turn the key to the “on” position with the car off, but don’t let it run. When the Toyota tire pressure sensor blinks three times, hold down the TPMS reset button until it stops blinking. Start the car, then let it run for 20 minutes to let the sensor reset. Under the steering wheel is typically where you’ll find the TPMS reset button.
On a Toyota Corolla, where is the reset button located?
Put the maintenance light out.
Corolla, Toyota Put the Corolla’s keys in. Don’t start the car; instead, turn the key to the “On position. In order to make “Trip A” appear on the main screen, press and hold the trip reset button next to the odometer. Reset the key to “Off.”
On a 2010 Toyota Camry, where is the TPMS reset button located?
Open the glove box to reveal a reset button that is tucked away beneath a little lip to the left of the glove box. Hold down the button until the TPMS light gently blinks three times.
The TPMS reset button is where?
Tire pressure monitoring system is referred to as TPMS. The TPMS reset button is often located below the steering wheel. Your car’s TPMS needs to be electronically reset after you replace the tires in order to erase the error message. Hold the TPMS reset button down until the tire pressure light blinks three times, then let go of the button to complete the process. Your car should be started, and the sensor will refresh after 20 minutes.
Why, Toyota, does my tire pressure light remain on even after filling the tires?
Try the following if your TPMS light is still on after you have inflated your tires to the recommended pressure: 10 minutes at a speed of 50 mph would be plenty. When you start the car again, the TPMS light ought to be off because this ought to reset the tire sensors.
Why is my tire pressure light on when my Toyota Corolla’s tires are fine?
Several cars now come with a built-in tire pressure monitoring system (TPMS). An indication light will flash on your dashboard if the air pressure in your tires drops below the recommended level.
The information system in the dashboard may have a menu that shows you which of the four tires is malfunctioning. The TPMS indicator may be on in a number of circumstances, however your tires may not require replacement or upkeep.
If this occurs and all of your tires seem to be in good condition. This light may illuminate even if your tires are in good condition for a number of different reasons. The decrease in outdoor temperature is one explanation. To double-check and confirm it, it is advisable to maintain a tire pressure gauge in the automobile.
Why is the pressure in my tires light on?
The TPMS (Tire Pressure Monitoring System) is designed to notify you when a tire’s pressure is too low and may result in hazardous driving situations. If the indicator is on, your tires may not be properly inflated, which might result in premature tire wear and even tire failure. It’s critical to comprehend the value of appropriate tire inflation and how TPMS can prevent a potentially hazardous situation.
Both excessive and inadequate tire inflation can result in early tread deterioration and potential tire failure. Increased traction, early wear, and an inability to withstand impact from the road can all be effects of overinflation. The middle of the tread on tires with excessive air pressure may prematurely wear out. Underinflation, on the other hand, results in slow tire reaction, reduced fuel efficiency, excessive heat buildup, and tire overload. Both sides of the tread edges or shoulders will prematurely wear out on a tire that is underinflated.
Finding the TPMS indicator on your dashboard is easy if you’re just learning about tire pressure sensors. It is a light that has a horseshoe form with an exclamation point in the middle.
What is the Toyota Corolla’s typical tire pressure?
How can I determine my Corolla’s tire pressure? Comparing the valve reading to the 32 PSI tire pressure advised for your Corolla If the pressure in your tires is too low, blow air into them until they reach 32 PSI. To release some air if your tire pressure is too high, push the valve in.
What is the Toyota Corolla’s recommended tire pressure?
pressure in a Toyota Corolla tire The 2019 Toyota Corolla’s recommended minimum tyre pressure is 35 psi, according to this tire placard. This is equivalent to 2.4bar and 240kPa.
My tires are in good condition, so why is my low tire pressure sign on?
Typically, a tire with an air pressure that is 10% to 15% low will turn on the warning light. The air pressure inside the tires also tends to drop in cold or icy conditions. Short trips in the car will warm up the tires and raise the pressure in them.
Should the TPMS be reset after purchasing new tires?
After changing or rotating your tires, or after adding new sensors, you should always reset your TPMS. Even after you have inflated your tires, some sensor manufacturers advise restarting the device. By teaching the primary TPMS system to identify the sensors in their new locations, resetting the TPMS is frequently referred to as retraining the system. TPMS reset procedures vary from vehicle to vehicle and typically involve a specific sequence of ignition and pedal actions, a configuration change in your dashboard menu, or the use of a TPMS Reset Tool.
What does the 2010 Toyota Corolla’s maintenance required light mean?
On your dashboard, the Toyota maintenance light may read “MAINT REQD. It’s a light that is always on and alerts you when you require an oil change at a licensed auto shop. Your Toyota will run more smoothly and efficiently if you change the oil in your car.
How can you turn a Toyota’s maintenance needed light back on?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
Can the tire pressure monitoring system be turned off?
On the gauge cluster of your car’s dashboard, a horseshoe-shaped emblem with an exclamation point lights when your tire is underinflated. The tire pressure monitoring system is the piece of equipment that generates this signal (TPMS).
Sensors provide the TPMS with data on the air pressure level. The air pressure sensors inside your tires or the anti-lock brake system’s wheel speed sensors may be used by your car’s TPMS, depending on the model.
Tire pressure sensors’ batteries may they be changed?
The Tire Pressure Monitoring System, which notifies you when a tire is dangerously low on air, typically uses TPMS sensors embedded in the tires to detect low tire pressure. The majority of TPMS sensors use internal batteries that cannot be changed to power them.
The lithium ion batteries in a TPMS sensor have a lifespan of 5 to 10 years. The duration of the TPMS sensor batteries is difficult to predict because it depends on how many radio frequency broadcasts the sensors send out. The amount of driving you perform over time and the conditions you drive in will affect the sensor battery life. The TPMS battery life is less affected by cold conditions than by warmer ones. When compared to continuous pace, stop-and-go traffic has a greater effect on TPMS battery life. This is due to the fact that sensors send out more radio frequency broadcasts as a vehicle changes its speed.
The system will issue a malfunction warning when a TPMS sensor’s battery runs out, which will be visible as a blinking TPMS light on your dashboard. After 60 to 90 seconds, the light may either continue to flash or turn solid. Be a repair appointment as soon as you can if you receive this warning, but also check the tire pressure in each tire right away to make sure you have safe inflation all around.
You can change each individual TPMS sensor separately if one of them malfunctions and needs to be replaced. The other sensors, on the other hand, are probably on the verge of failing as well if the failure was brought on by a dead sensor battery. You might wish to proactively replace all the sensors so you have brand-new sensor batteries all around when you take into account the time and hassle of taking your car off for a sensor replacement.