The front and back doors of a 2016 Toyota Corolla have separate exterior door handle removal procedures. Open the door and take out the rubber grommet at the end of the door to remove the front handle. At the grommet’s base A T-30 torxBolt will be visible; turn it counterclockwise to remove it. Pull out the lock, jiggle it a little, and remove it. It will easily come out if you grab the handle and pull it in the direction of the car’s back. The three T-30 torx Bolts holding the latch must be removed in order to remove the rear door handle. The handle bolt, which is located above the latch, will now be accessible. Once this bolt is taken out, the handle will come off in the same manner as the front.
In order to replace the external door handle on a 2016 Toyota Corolla, use a screwdriver to pry open the switch panel and pull it forward. The switch panel should be disconnected and set away. Pry open the armrest tab now, then take off the interior mirror panel as well. To remove the clips keeping the door panel in place as well as the two screws holding the armrest in place, follow these steps. Pull back the water shield and then remove the door panel. Near the door handle, you will discover a clip inside. Flip the clip off the rod and pull the rod out. Another clip can be found close to the lock; flick it off as well, then remove the rod. The handle ought to now be free to pull out once the two 10mm bolts have been removed. Fit the new handle into the slot where the old handle formerly was, then switch the lock mechanism to it. Reinstall all the panels, rods, clips, and screws at the end.
In This Article...
How is a Toyota automobile door handle changed?
First and foremost, you must purchase an OEM replacement outside door handle. For the reasons listed here, we do not advise purchasing an aftermarket replacement handle.
A Toyota dealer may sell you an OEM replacement door handle, but be prepared to pay a premium. On our website, however, you can get a genuine OEM Toyota door handle at a discount. To see every door handle we have available for your Toyota, search for it in our catalog.
What is the price of a new automobile door handle?
Oh no! Although a car door handle is a crucial component, happily, replacing one won’t set you back a fortune. Depending on which handle broke, the price varies, but you should budget between $80-$500 to repair it.
The average cost to replace the interior handle, including labor, is between $80 and $200. It will likely cost between $150 and $500 for the external handle. Having said that, these figures could vary greatly depending on the car you drive and the service facility you go to.
Ask for quotations from a few body shops to get an idea of the price for your specific car. You can then choose what is best for you.
It never hurts to have additional protection on your automobile with a roadside assistance subscription from Jerry, even though mishaps and broken door handles do happen. You receive industry-leading roadside assistance from Jerrys membership, featuring advantages like towing, lockout service, and a mechanics hotline. You can check the app or contact one of our helpful agents to see whether you qualify. A special deal of $50 for your first year might be available to you!
How is the front door handle removed?
You must now replace your handle and knob after cleaning, painting, or doing any other necessary maintenance on them. Fortunately, you are more familiar with the parts now. You will mainly just be turning the process around. I shall therefore only touch on the essential aspects.
Reinstall the handleset by first going through the latch and through the hole. Reposition the screws in the holes after that. At this stage, you can only screw them down a small amount. Reinstalling the internal plate is the first step. Align the big holes with the screws, and then turn it in the arrows’ directions. Finish tightening the screws to lock the plate.
Here comes the knob. Examine the interior of the doorknob. Before you put the knob back into the door, you should notice arrows showing which direction the lever mechanism needs to be aligned. In order to align the arrows, look at them. Reinstall the doorknob by lining it up with the doorhole. ReminderDon’t press it up against the door just yet.
Return to the same notch you were in when you removed the doorknob once it is in the door. Put as much pressure as you can on the interior mechanism while holding the doorknob, then slide your flathead screwdriver under the lever. When removing the knob, push the lever in the opposite way. Slide it all the way until there is no more room for movement. The doorknob should now be locked back in place at this point. Verify its security via testing. Next, firmly reinstall the plate cover.
Are new automobile door handles simple to install?
If you’ve had your car for a while, you probably don’t give the door handle much thought until you need to use it one day and it feels “odd.” Even if you can’t quite place it, something doesn’t feel right. The door appears to be locked even though the handle appears to work.
You obviously try using the key or the remote a few times, but it doesn’t seem to be workingit appears you are locked out of your own automobile. It works when you try the other door or even the back door. Great! The center console or even the back seat must be climbed over in order to enter and start your car. At least you can get in the car and drive home, even though it is at best undignified and at worst nearly impossible.
It’s possible that the inside door handle will fail first instead of the driver’s door handle; however, since the driver’s door is the one that gets the most use, this is typically the case. The business end, which is the part you cannot see, gradually cracks and then snaps off because the majority of these handles are composed of plastic or a cheap cast metal.
Although the process for changing the handle varies from car to automobile and in some cases necessitates disassembling the inside of the door, many may be replaced quickly and easily from outside the door with just a few simple steps.
How much time is required to repair a car door handle?
Hello and thank you for your letter. Depending on the car and whether or not the door can be opened from the inside. It takes about 1.5 hours to complete the work. On some makes and models, it might be more. For a more specific response the next time, I’d advise including information about your car. Consider YourMechanic if you require help replacing a door latch since one of our mobile technicians can visit your house or place of business to complete the task.
Can a door handle be reattached with glue?
The good news is that it’s simple to fix a door knob if you’ve noticed the handle beginning to sag. Simply carry out these actions.
- Remove. You’ll need to remove the handle to see the mechanism behind if you can’t see a broken or loose screw in the door plate that needs replacing or tightening.
- Reassemble. On top of the backing plate, clip the base back into position. Put the handle or knob back on the spindle shaft and tighten it (if it’s an exposed set-screw handle) or align the detent with the access hole (if it’s a hidden screw handle) and click it back in.
- Pry. You must now take the base out. Gently remove the ring free with a flathead screwdriver, being careful not to harm the backing plate.
- If the door handle has a concealed screw, locate the detenta spring-loaded pin that protrudes from the handle or knoband its access hole. Use a flathead screwdriver to apply pressure to the detent to pry the handle off the spindle shaft.
- The door handle or knob can be removed from an exposed set-screw door handle by simply removing the screws with a screwdriver.
- Tighten. You should now be able to see a set of screws holding the mechanism together. Each screw runs through the door from the interior backing plate into the exterior backing plate. Tighten these screws while holding the back plate firmly in place.
Apply high strength adhesive to the screws in the door plate and backing plate to further increase resistance to normal wear and tear. Simply unscrew, clean off any debris or dust, and wrap each one in a small bead of adhesive before screwing them back in.
UniBond Repair Severe, which uses proprietary Flextec technology, offers a powerful grip that is incredibly resistant to stress and shock, as well as water and extreme temperatures, making it the perfect solution for fixing loose door handles on both internal and external doors.