Just finished mine and discovered a substitute. I came some clips with straightforward plastic domed heads. With a medium flat head screw driver and some gentle easing from underneath the carpet, I discovered that ordinary clip prying was simple. It was simpler to remove all 10 and slide the cover from behind the lock than to fiddle with the latch. By carefully pulling the clip with a fingernail until it releases and slides off, the power connector can be unplugged. To turn the bulb holder clockwise, apply pressure with your hand. It will start to release and then slide off. Remove the bulb firmly. Replace the lamp holder with a #168 bulb before replacing the power connection by hand. If the bulbs pass the test, reinstall the covering and install the clips with force. Done. The forked clip tool would be simpler, but the screwdriver wasn’t horrible; all it took was a little even-handed prying to get it going. Use only your hands and a flathead screwdriver to enjoy. Just finished mine and discovered a substitute. I came some clips with straightforward plastic domed heads. With a medium flat head screw driver and some gentle easing from underneath the carpet, I discovered that ordinary clip prying was simple. It was simpler to remove all 10 and slide the cover from behind the lock than to fiddle with the latch. By carefully pulling the clip with a fingernail until it releases and slides off, the power connector can be unplugged. To turn the bulb holder clockwise, apply pressure with your hand. It will start to release and then slide off. Remove the bulb firmly. Replace the lamp holder with a #168 bulb before replacing the power connection by hand. If the bulbs pass the test, reinstall the covering and install the clips with force. Done. The forked clip tool would be simpler, but the screwdriver wasn’t horrible; all it took was a little even-handed prying to get it going. Use only your hands and a flathead screwdriver to enjoy.
In This Article...
How is a license plate light installed?
A license plate light installation guide:
- Buy new license plate lights as the first step.
- Step 2: Take off the housing cover for the license plate using a flat screwdriver.
- Step 3: Carefully remove the bulb housing, then unscrew the original bulb.
- Step 4: Replace the old LED light with the new one and screw it firmly into the housing.
How is a tag light removed?
We always advise consulting your service manual before you start, or if you have any queries regarding your particular car.
- Step 1: Open the tailgate or trunk.
- Step 2: Remove the tail lamp assembly (if needed)
- Step 3: Remove the bulb.
- Step 4: Insert a replacement bulb after adding bulb grease.
- Step 5: Reattach the component (if needed)
AutoZone will they replace brake lights?
Problems with the brake light switch or turn signals A replacement switch can be placed after you check the connection to the switch for corrosion or other problems and buy it at your neighborhood AutoZone.
Are the taillight bulbs reachable?
[00:00:30] Hey, I saw that your taillight was out when you pulled into the store. – Wow, are you serious? Is there anything we can do to solve this now? – I’ll demonstrate for you how simple it is. – [Larry] When you notice a light bulb is out, ask a friend to help you test all the lights in your car to find the particular bulb that’s blown. This is because there may be more than one bulb in a given light assembly. Once you’ve identified the blown bulb, you may either visit an auto parts store and get the numbers right away, or you can use your owner’s handbook or an online site to find the replacement bulb’s number.
[00:01:00] Now, in some cars, the back bulbs can be accessed by a panel in the trunk or the back hatch. To access the bulbs, you’ll need to open a panel door or cut away some internal trim. In order to remove the trim panel itself, you might also require a flat-head screwdriver to release a retaining clip. However, you’ll need to remove the taillight assembly if your automobile lacks an access panel. Inspect the assembly for plastic fasteners securing it to the body. With a flat-head screwdriver, the fasteners can be carefully peeled apart, but use caution.
not to [00:01:30] bend or shatter them. The screws holding the taillight to the car’s frame should then be removed and placed in a secure location. Try carefully jiggling and wriggling the assembly to get it pop out with all the screws removed. Use a flat-head screwdriver if you need more assistance, but be delicate since taillights are frequently made of plastic and are expensive to replace. Connectors can be seen in the back once the assembly has been removed. Remove the bulb by turning the connector’s base.
[00:02:00] Note the burned-out or black bulb as well as the missing filament. Because taillight bulbs don’t produce a lot of heat like halogen lamps do, you can touch them. To avoid getting oils or grease on the glass, it is still a good idea to wear gloves or a towel when replacing a new bulb. Install the replacement bulb into the plastic housing with care, being careful not to bump the sides. Twist it one more after it has been inserted to secure it. Now test the bulb with your friend before fastening the screws.