The lights and grill surrounding the headlights must be removed in order to replace the headlamp assembly in your Toyota Tacoma pickup, but this can be done with a few hand tools. To light up the road and the area in front of the vehicle, the headlight assemblies are made of a composite material. Moisture or debris entering the assembly can reduce bulb life if the assembly is damaged. If the headlight assemblies are stained or severely scratched, they could also need to be replaced.
In This Article...
Step 1
Your Tacoma’s hood may be opened, and the prop rod can be used to support it. Find the three screws holding the side marker lights in place. One screw is on the top of the light, and there are two screws in the lens. Utilizing a screwdriver, take out all three.
Step 2
Unplug the electrical connector on the back of the marker light assembly before removing it from the truck. Set away the electrical connector. On the marker light opposite, repeat this procedure.
Step 3
Find the seven clips that hold the grill in place on the truck’s front. There are three on the bottom and four along the top of the grill. Pushing the clip downward with a flat screwdriver can release it.
Step 4
Find the two clips on the grill’s lower corners. In the grill’s lowest corner, there is one on either end. To loosen these clips, reach through the opening in the marker light with a pair of long-nosed pliers.
Step 5
Remove the nine clips and the grill, then set the entire assembly aside. On the headlamp assembly, find the two nuts and one bolt. Slide the headlight assembly forward after removing them with a socket and ratchet. Remove the headlight assembly from the truck and unplug the electrical connector from the headlamp.
Step 6
Install the retention bolt and two retaining nuts after sliding the new headlight assembly into the truck and plugging in the electrical hookup. With a socket and ratchet, tighten the bolt and nuts.
Step 7
Reengage the nine clips holding the grill in place as you position it on the truck. To fasten the grill, snap the clips back onto the truck’s body. You’ll see that they secure themselves.
Step 8
Plugging the electrical connector into the back of it will allow you to install the side marker lights. With a Phillips screwdriver, attach the three retention bolts and tighten them. The lens will break if the screws are overtightened.
- Set of metric sockets
- flat-head screwdriver
- tool for Phillips screws
- extended-nose pliers
How do I adjust the headlight level?
Vertical field should be adjusted. Locate the adjusting screw and slowly move it in either the clockwise or counterclockwise direction to change the height of the lights. Ensure that the most intense portion of the headlight beam strikes at or just below the vertical centerline you marked with tape on the wall when you make your adjustment.
What adjustments should be made to headlights?
Turns should be made clockwise to raise the lights and counterclockwise to reduce them. After adjusting, turn on the headlights and study the lighting pattern on the wall. The apex of the beam’s most intense portion should be either directly above or slightly below the center of the taped line you established.
Are the headlights on all 2nd generation Tacomas the same?
Let’s face it, the 2nd generation Tacomas’ halogen headlights aren’t really impressive. If I were being completely honest, I’d even say they are somewhat out of date, especially today.
Halogen lights are obsolete thanks to current technologies. Halogen lamps don’t produce the best light, and their appearance isn’t particularly appealing. They also generate more heat than the majority of current bulbs on the market. However, if a bulb has to be changed, they are conveniently accessible.
The headlights have maintained the same overall design since the initial 2nd Gen was debuted in 2005, with a slightly more modernized version being used from 2012 to 2015. The halogen bulb and a sizable reflector designed specifically for the halogen lamp are standard equipment for these revised headlights.
Nowadays, aftermarket LEDs or HIDs can essentially replace halogen bulbs. Do those bulbs fit perfectly? Yes, however this isn’t the correct or ideal approach to boost your headlight output. The reflector bowl is made for a halogen, not an LED or HID, thus this isn’t what you’d call a real LED or HID conversion. Bulb swaps will never provide a real retrofit, no matter how near manufacturers come to the diode positioning on LEDs or the filament placement on HIDs.
Changing a halogen bulb with a reflector designed exclusively for halogen bulbs will merely scatter the light. Only halogen-type bulbs could use the headlights’ factory-installed reflector. They effectively reflect the light downward and onward, not into the trees or into the eyes of oncoming drivers.
A headlamp retrofit is what?
Looking to balance out the output of your headlights and lessen glare? You might require one of our projectors for retrofits. To give better light projection than OEM headlights, retrofit projectors are installed in headlights. Retrofit projectors with LED, xenon, or bi-xenon technology are compatible with reflector-based halogen lamps. The retrofit projectors from ORACLE may also lower the output of LED headlights. Our retrofit projectors guarantee the finest headlight boost after installation.
Projectors that may be retrofitted offer several wonderful advantages. For instance, in contrast to ordinary headlights, which project light forward, retrofit projectors focus downward. This improves your visibility on the road while reducing headlight glare for other motorists. The road-hugging characteristics of a car are also highlighted by retrofit projectors, giving any vehicle a naturally more svelte and fashionable appearance.
What do projector headlights do?
As you are already aware, reflector headlamps are used. With the addition of a lens up front, the projector headlamps are the same assembly as before. This enhances the headlamps’ visibility by increasing their range and directing them more effectively. Since this item is made of one piece, the bulb cannot be replaced directly. Because of this, it is a complicated unit with better outcomes.
- higher light
- expensive to produce
- costly to replace
- occupy more room
Both are advantageous and depend on the buyer’s capacity to pay. Of course, the projector headlamps are better and produce more light. They will also have a longer lifespan because they are an insulated component.
A projector headlight can also feature a yellow bulb; white light is not a requirement. White bulbs can be found in standard headlight assemblies as well. Therefore, it is not a definition of color. Why do certain cars have projector headlights and a yellow light? In general, yellow lights are more visible in the fog. As a result, many automobiles continue to employ yellow instead of white.
Do LED bulbs fit in my Tacoma?
Although the Toyota Tacoma from 2016 to 2022 is a solid worker, there is still plenty of potential for LED improvements. Consider Toyota Tacoma LED lights if you want to replace or update your truck’s bulbs. Our LED lights will improve your nighttime visibility and give you a contemporary look whether you’re driving your truck around a job site or on the trails. Fog lights, reverse lights, and bumper light bar mounts are just a few of the places on your Tacoma where Diode Dynamics offers high-quality LEDs. Try our LED replacement bulbs and upgrades if you want to improve your nighttime vision or give your truck a custom flair.
Describe HID vs. LED.
Cars with LED and HID headlights have equipment and bulbs that make it easier for drivers to see at night. Up until recently, the majority of automakers used halogen lights in their vehicles, which heat a filament using argon and nitrogen gases to produce light.
High-intensity discharge headlights, often known as HID headlights, use a mixture of metals and gases to produce a brilliant blue-white light when the filament is heated. Some HID lights charge xenon through electrodes with high voltage rather than using a filament. HID headlights are high-end headlights that are popular because of their brilliance and durability. Driving at night is made much safer with this type of headlight.
Light-emitting diode headlights are what they sound like. They transport the energy-emitting photons that produce light using semiconductors. Some of these headlights need additional fans or heat sinks to regulate the temperature because they can get very hot.
The following are some of the main traits and variations between each:
- Price: Though costs might vary by type, HID headlights are frequently less expensive than LED headlights.
- LED lights frequently have bulbs with locking tabs, heat sinks, and diodes. HID headlights may include electrodes, electrode chambers, outer bulbs, and locking tabs.
- Energy consumption: Both consume more energy than halogen, but LEDs are marginally more energy-efficient.
- LED lights turn on immediately, whereas HID bulbs’ heating filaments may take a moment to ignite.
- Lifespan: HID lights have a life expectancy of about 15,000 hours, whereas LED lights may last up to 45,000 hours.
- Both HID and LED lights have a decent range, typically up to 300 meters (about 985 feet).
- Color: A variety of hues can be produced by both LED and HID lights.
- LED lights have a brightness range of 9,00010,000 lumens, however HID lights may only have 8,000 lumens. However, both are more vibrant than conventional halogen lights.
- Technology: HID lights require gas, while LED lights use electricity (typically xenon).
What is the brightest permitted headlight bulb?
The brightest bulbs you can get for your automobile that are also street legal are probably xenon headlights, which are frequently mistaken for high-beam lights.
However, this group of extremely bright and energy-efficient lights can be utilized as taillights, parking lights, reverse lights, or turn signals. For optimal heat dissipation, these bulbs are completely enclosed in aluminum.
One buyer was ecstatic to try these LED lights because of their brightness “mowing until dusk. They added, in addition, “How intelligent they were caught me off guard. They use around half as much energy as OEM bulbs, which is better for the charging system. It will now slightly speed up the starter battery’s recharge.
How far should your low beam headlights project?
Depending on the headlights you’re using, your headlights should shine a certain distance. High beams or brights should shine 350 to 400 feet in the distance, while low beams or dipped lights should shine roughly 150 to 200 feet away. For maximum effectiveness, fog lights must be positioned at a specific height; they do not need to illuminate the road in front of them.
Read on to find out everything you need to know about how far your headlights must shine, including how to examine each type, align them, and more!
How Far Should Your Headlights Shine While on High Beam (Brights)?
High beam headlights, sometimes referred to as brights, should illuminate the road in front of you for approximately 350400 feet (107122 meters).
High beams are advised for when you’re travelling quickly, thus this is roughly twice the distance needed for conventional headlights.
How can I make the headlights on my projector brighter?
How to Brighten Projector Headlights: 10 Tested Techniques
- Improve your headlights with HID or LEDs.
- Headlight Aim should be adjusted.
- Keep Your Headlights Clean.
- Headlight Lenses need be changed.
- Including a Headlight Cover
- Change the bulbs in your headlights.
- Invest on a New Headlight Housing.
- Place a headlight relay kit in place.
How much does aligning headlights cost?
Headlamp alignment adjustments typically cost between $41 and $52. Between $41 and $52 is the expected labor cost range. Taxes and other costs are not included in this range, nor are your particular vehicle or geographic area taken into account.