In order to change a brake light bulb in a Toyota RAV4, you must first enter the cargo area in the back of the car. Two panels that can be removed are located next to the brake lights in the back of the cargo area. You may reach the bulbs in the housings by removing these panels. The bulbs can then be turned a quarter of the way around and removed from the housing. After that, you can take the wiring from the bulbs’ backs. Once the bulbs are broken, you can replace them with fresh ones to make the system functional once more.
Open the rear lift gate of a Toyota Rav4 and remove the two bolts holding the taillight assembly to the rear quarter panel in order to change the brake light bulb. The assembly’s upper bulb socket houses the brake light. Pulling the socket out of the assembly’s back requires turning it counterclockwise.
In This Article...
How can I swap out the bulb in my brake lights?
Replacing a Tail Light
- Step 1: Open the tailgate or trunk.
- Step 2: Remove the tail lamp assembly (if needed)
- Step 3: Remove the bulb.
- Step 4: Insert a replacement bulb after adding bulb grease.
- Step 5: Reattach the component (if needed)
- Repeat step 6 on the opposite side.
Why is my RAV4’s brake light on?
Your Toyota RAV4’s dashboard will display the word “BRAKE” if the braking system is malfunctioning or the brake fluid level is low. You need to repair this problem right away before you can keep driving.
How is a rear tail light assembly taken out?
Safety Advice
Always use safety eyewear when performing maintenance on your car. When necessary, put on additional personal protective equipment (PPE), such as latex gloves or closed-toe shoes.
On the back of your car, find the tail light assembly. When you use your brakes or turn signal, they illuminate on each corner.
Remove any mounting screws that are present on the exterior of the tail light assembly, if necessary.
Can I change a brake light on my own?
Anyone can learn how to replace a broken brake light. A replacement bulb costs approximately $10, and doing it yourself will save you about $20 in labor costs as well as the time it would take to drive to the shop and wait for the work to be completed.
AutoZone will they replace brake lights?
Problems with the brake light switch or turn signals A replacement switch can be placed after you check the connection to the switch for corrosion or other problems and buy it at your neighborhood AutoZone.
Is it simple to replace a brake light?
Although you don’t have to bring the broken brake light bulb with you when you go shopping, having it nearby helps you make sure you obtain the proper replacement bulb.
Find the appropriate brake bulbs for your vehicle’s make and model by going to a website supplier.
Consider buying two bulbs and storing a spare in your glove box. The other brake light will probably soon fail if the first one has.
Stage 4: Introduce and Test the New Bulb
Drive the holder and bulb into the tail light assembly, then tighten it by rotating the holder clockwise.
Make sure the tail light assembly’s bulb and holder are both firmly in place.
Have someone sit in charge and operate the brakes while you gaze behind and observe light movement.
It’s simple to replace a brake warning lamp. Without an expert’s assistance, you can carry it out on your own at home. But if you get stuck at any moment, you could need their assistance. Simply removing the old bulb and replacing it is all that is required.
When replacing a light bulb, you must remove screws with a flathead or screwdriver. You won’t even need one if your car’s design allows for simple access to the taillight housing.
At any time, your brake lights could malfunction. Police officers may swing by to make sure you are aware of the broken light bulb. The punishments in these circumstances may be a little severe.
If you just bought a car, you might be curious about how to change a brake light. Don’t disregard this problem because it might make nighttime driving uncomfortable. In order to prevent accidents, it’s critical to always drive with enough light. Be sure to seek the assistance of experts if you lack the confidence to complete this activity.
On a Toyota RAV4, how do you reset the ABS light?
Moving thread to 4.3 Mechanical Adapted from a sticky thread there about the ABS codes:
Even unplugging the battery will not erase any ABS/VSC codes or lights. By connecting a jumper wire to pins 4 and 13 of the diagnostic port, you can erase these codes from the Skid Control ECU. Immediately after turning on the ignition, press the brake pedal eight or more times. The brake lights must flash eight times in less than five seconds by lightly pressing the brake pedal. The lights and codes ought to disappear after turning off the key and taking out the jumper.
What does a Toyota Rav4’s exclamation point light mean?
Look for the horseshoe-shaped light with an exclamation mark in the middle since a flat tire can ruin your day. This warning light means that your Toyota’s tires need to have air added, therefore you should go to a dealership or service center. If you don’t, your car may be more prone to getting a flat tire. Additionally, because the tires won’t spin as smoothly, it will decrease your fuel efficiency.
Brake System Warning Light
There are various possible meanings when you see BRAKE in all capitals. It’s possible that the brake system is broken or that the brake fluid is low. However, if the parking brake isn’t fully released, the light can also turn on. You should be good to go if the light goes out once you release the brake.
Malfunction Indicator Lamp
This lamp resembles a car engine. If it shows up on the dashboard, one of the following could be broken:
- engine control electronics
- throttle control system with electronics
- electronic system for controlling an automatic transmission
Electric Power Steering System Warning Light
There may be an issue with the electric power steering system if you notice a steering wheel with an exclamation point next to it. If the light comes on, you should have your RAV4 checked out as soon as possible.
Seat Belt Reminder Light
This signal simply indicates that the driver or front passenger hasn’t buckled their seat belt all the way. It looks like a person wearing a seat belt. When you’re finished, the light ought to go off.
Low Fuel Level Warning Light
You can tell you’re low on gas when you see an image of a fuel pump (at 2.4 gallons or lower remaining). The light should go out when you fill the tank, so do it right away.
Are the brake light and the tail light interchangeable?
Many automobiles have a single globe that houses both the braking and tail lights. In other words, both lights have the same external covering. Your car’s may be a little different, with individual globes. In contrast to brake lights, which turn on instantly when you hit the brakes, tail lights are activated by turning on your headlights or applying the parking brake. The brake lights are a brighter red than the tail lights, which are typically red on cars. White back-up lights are also included in your rear lights.
How much does a new tail light assembly cost?
Cost of replacing a tail light Expect to pay between $200 and $500 if you elect to have a professional replace your tail light assembly. If you own a high-end luxury or performance vehicle, the cost of the job may increase.
Can AutoZone repair damaged tail lights?
Shop online or visit your neighborhood AutoZone for nearby tail light lens repair. Having a practical fix for cracked, chipped, or damaged tail lights is crucial for both emergency situations and regular car maintenance in your garage.