The process of changing the starter on a 2004 Toyota Corolla is explained in the steps that follow. The Corolla, Matrix, or Pontiac Vibe from 2003 to 2008 might also use these instructions.
In This Article...
Where is the starter located on a Toyota Corolla?
On a Toyota Corolla, the starter is located directly over the oil filter. as shown in this picture. The oil filter, which is dusty orange/black and out of focus, is in the lower left corner of the image. In close proximity to the image’s center is the starter with the solenoid attached.
After that, unplug the solenoid’s electrical connections. One of these is a plastic connector that needs to be removed by pushing down on the side tab with your thumb or a flat-head screwdriver.
Next, unscrew the bottom and top 14mm bolts that are holding the starter in place. To reach the top bolt, you might wish to use a socket extension (3).
Delete the outdated starter. Use a rubber mallet to give it a few whacks if it doesn’t come loose right away. The old starter, after removal, is shown here.
The new starting will take over the same spot as the previous one. Reinstall the bolts in the opposite direction.
Reconnect the negative battery terminal after replacing the starter.
You really can complete this task on your own, I assure you. Do yourself a favor and make the repair yourself to save a few hundred dollars.
How much does a Toyota Corolla starter replacement cost?
Estimated price for replacing a Toyota Corolla starter. Replacement starters for Toyota Corollas typically cost between $273 and $434. While parts are priced between $212 and $358, labor is predicted to cost between $61 and 77.
How much should a starting replacement cost?
I’m sorry to hear that your car is having problems. You should also account for labor charges, which might run from $150 to $1,000. A new starter may cost between $80 and $350.
The average vehicle’s replacement starter costs roughly $500. Your mechanic appears to be charging you the standard rate for this work. However, you should plan an additional $100 to $200 on top of that charge. The mechanic might find other issues, such as a crankshaft or ring gear trouble.
A starter includes the following parts, among others:
- either permanent magnets or electromagnetic field coils
- Switch fork
- Brushes
- Solenoid
- Commutator and armature
- gear for the starter
- bushes and bearings
Remember that you have to totally remove the starter from the engine area. This can result in a hefty labor charge.
The starter is more readily accessible in some cars, and removal takes less than an hour. Some cars are more complicated than others, such those where the starter is hidden beneath the intake manifold. These are substantially slower cars. The complexity of the repair, which is partly decided by your make, model, and year, will determine the final cost.
If you truly believe that your repair bill was overpriced, you can always challenge it.
What occurs when a car’s starter fails?
Imagine that you need to travel someplace and that you rely on your car to get you there as quickly and comfortably as usual. Already, you can see the smooth journey, your favorite radio show playing in the background, the warmth on, and perhaps a cup of coffee at your side (but be careful!). You then unlock the door and get into the driver’s seat. Like a thousand times before you turn the keys (or, if your automobile is a relatively new model, press the “start” button”). Nothing occurs. Why, you ask? It cannot be the battery because all of your lights are on and there are no indications of a low power source. A stunning realization follows. You have a failed or defective starter motor. Have any warnings gone unheeded? Did you have a list of warning flags handy?
We hope that this post will help you understand a problem that is more widespread than you may realize if you believe this could apply to you. As a garage, we deal with bad starter problems on a regular basis. They are rather common. We have provided links to clear explanations for some of the less common terms we’ll be using because we’ll be getting into some technical aspects. After all, not everyone here loves cars!
The primary motor, which turns your crankshaft and fires up your engine, and the solenoid, which simultaneously engages the starting’s drive gear and shuts the electrical contacts on the main motor, make up a starter. Poor maintenance practices or simple wear and tear may be to blame for starting system issues. The various system parts endure significant wear over their service lives, even with good maintenance, and eventually develop issues. The burden on starting motors and batteries has significantly grown as stop/start technology is being installed in an increasing number of automobiles.
Solenoids and starter motors rarely completely malfunction. The following warning signals should alert you to potential problems with more than one component of your car, so be sure to call your trusted neighborhood garage to schedule a thorough inspection.
Grinding noise
It frequently makes a grinding noise when the starter drive gear is worn out or not engaging properly. This sounds a lot like the sound you make when you unintentionally turn the ignition switch back on after starting your car. The engine flywheel could be harmed if the grinding symptom is ignored.
Freewheeling
When you turn the engine over and all you hear is a whining sound, this is known as freewheeling.
This indicates that the starter is not engaging with the flywheel when it happens. This frightening circumstance may necessitate replacing the entire component. If this occurs, get your car serviced as soon as you can.
Intermittent issues starting the vehicle
The relay is most likely to blame if you try to start your automobile and the engine doesn’t fire up right away but you hit the switch again and it starts. Since the starter relay is an all-or-nothing mechanism, it either sends the starter the full electrical current or it doesn’t. When you turn the key, the starter occasionally makes a clicking noise due to a faulty relay.
Starter stays on after engine started
The circuit that will cut off electricity to the starter motor is designed to close when you start the engine and release the key (or cease pushing the starter button on a new car). If this continues to operate after the engine has started, the solenoid’s main contacts have probably fused together in the closed position. The relay will become trapped in the “on” position if this issue is not fixed right away. The transmission flywheel and the entire starter system will eventually sustain significant damage as a result of this.
Smoke
The starter gear will eventually overheat if power is continually provided to it. Smoke is typically a sign that the electrical supply is being drained too much. This is either a result of the starter running too long without a break or a connection issue. A burning smell and smoke coming from behind the engine may indicate more serious issues.
Batteries
Even though it might seem like you have power to your starting system, such as if your headlights and dashboard lights are on, the engine won’t start. This could be deceiving because starting your car requires a lot of battery juice. If your car won’t start, you can check to see if the problem is a weak battery by using jump leads or a starter pack. Nine out of ten autos that have starting issues in the winter have a battery issue.
Can I change a starter on my own?
The majority of people believe that if their automobile won’t start, the battery is to blame. They attempt to boost it, but it still won’t turn on. Obviously, it’s a beginner or something little more severe. The alternator receives a charge from the battery of the car through the starter. The alternator’s charge makes it possible for the car to start. The car is dead if the starter is worn out since it won’t accept or send a charge. A repaired starter is just as effective as a new one and is less expensive than buying a new one, which is pretty pricey [source: Allen]. Save money by replacing the starter yourself if it is the true source of the issue. How to change an automobile starter is as follows:
- In order to disconnect the negative battery cable from the battery, turn off the ignition.
- From the starter, unplug the positive cablethe substantial cable that connects to the battery.
- Using a ratchet, unplug each of the bolts holding the starter to the block.
- Any additional mounting brackets keeping the starter in place should be removed.
- The starter’s bolts must all be removed. Bolts that are difficult to remove or extremely tight should not be forced. Instead, use oil or lubricant to aid in removing the bolt.
- Take the starter out of the vehicle.
- The new starter should be mounted on the block and fastened with bolts. Reconnect the battery cable to the starter before tightening the bolts.
How can I tell if my starter is defective?
Still, keep an eye out for these seven indications that your starter is failing.
- #1: The Engine Won’t Start.
- #2: Loud, grinding, or whirring noise.
- #3: Occasional Trouble Starting the Car.
- #4: The Starter Continues After the Start.
- #5: Smoke.
- #6: The starter engages but the engine won’t turn over.
- 7. Battery
A 2004 Toyota Corolla starter costs how much?
For your 2004 Toyota Corolla, we now have 6 Starter items, with prices ranging from $118.99 to $195.99 in our inventory.
I don’t want to remove my starter, but how can I test it?
Q My 1999 Toyota Tacoma’s rebuilt starter has just been installed; the previous one had shorted out and refused to disengage. The new one, though, won’t interact. When the key is turned, all that can be heard is a quiet click. Any thoughts?
A Did you test the old starter to be sure it was defective? The starter may continue to engage if a relay or solenoid is shorted. Check all electrical connections between the battery, relay, solenoid, and starter, assuming the replacement starter motor is in working order. Take a close look at the starting relay’s socket. And ensure that the engine/drivetrain and the chassis have a strong ground connection.
Using jumper cables to disengage the car’s electrical system is the simplest approach to examine the starter. With the engine off and the transmission in “park,” carefully attach one end of the red/positive jumper cable to the battery’s positive terminal. Connect the red cable’s opposite end to the starting motor’s positive connector. The engine must be spun or cranked by the starter. If it does, the wires, connectors, or relay are the cause of the issue. If not, start the engine and use the black/negative jumper cable to establish a connection between the drivetrain and the battery’s negative terminal as a ground. Connect the red cable to the positive terminal of the starter. If the starter turns the engine over, a poor chassis ground is the issue.
Once more, use extreme caution when performing these tests to keep yourself safe. Remove the new starter, or even better, test it on your workbench.
Q I am rebuilding a 1988 Nissan Pathfinder V6 with 149,000 miles. One issue that I’d really like to fix is the fact that the engine always behaves as though the temperature is 30 below zero! The engine may be running at 2,000 to 2,400 rpm while the outside temperature is 90 degrees. Only the first start of the day results in this.
A A “fast idle control device” (FICD) and an idle-up solenoid are used by this early fuel injection system to regulate fast idle during startup. The crank angle sensor, coolant temperature sensor, ignition, and battery provide data to the FICD. Although the first idle speed of 2,000 to 2,400 rpm is correct, normal idle should arrive sooner. The two gadgets mounted on the throttle body would be checked.
Q My 1999 Chrysler Sebring has about 112,000 miles on it. My car won’t run correctly when the temperature is below zero. When I let up on the throttle or go into gear, it will start rough and die. Once fully warmed up, it functions normally. The gasoline pump may be the issue, but the dealer wasn’t sure, and fixing it would cost $900. What shall I do?
A Although low fuel pressure may be a contributing factor, the symptoms don’t really match a fuel-pump issue. Check the fuel pressure with a shop, then connect a scan tool to check for trouble codes. Have the shop verify the accuracy of the coolant temperature sensor signal with the engine completely cold. The idle air control actuator can be tested or reset using the scan tool.
Are basic maintenance items like air and fuel filters, spark plugs, and the like current on the vehicle as well? The car is approaching its operational limits when the temperature falls below zero, therefore regular maintenance can make the difference between the vehicle starting and not starting.
How is a starter bypassed?
In bypass starting, you apply a wrench or a screwdriver to the starter motor’s terminals, a tractor’s solenoid, or the terminals of other machinery. All tractor-neutral starting switches are bypassed by this. As soon as the circuit is complete, the starter engages, and the engine starts, sparks fly and electricity snaps.
How much does an Autozone starter cost?
Starting at $50 up to $350, rebuilding parts for a starter can be expensive. A new starter might cost anything between $80 and $350.