This step-by-step manual is based on Sienna models from 2011 and after. If you have an older Sienna model, you can still try to follow the instructions, but they might not be correct.
Here is how to replace the side door cable assembly in your Sienna without further ado:
- Remove the seat that is most near the broken sliding door. (Optional; it merely provides you with extra space to work on the door.)
- The window on the broken door should be rolled down.
- A hex screw keeping the plastic panel in place is located on the side of the door. Get rid of the screw.
- Reposition the lock so that it is in the open position. (This stops the lock from coming out when the plastic panel is removed.)
- Pry the plastic panel off gently. The panel is held in place by tiny white plastic retaining clips. Make every effort to properly pop them out.
- Pull off the entire plastic panel after closing the door (while still inside the van). Reach behind the panel and unplug the power window connector before you can remove it entirely.
- Once outside, turn your back on the door and lower the window. There is a window molding there. Pull out the window molding after prying off the clip holding it in place. To get it out, you might need to move it back and forth.
- Go to the quarter window in the back. The side door cable is hidden beneath the window by a plastic cover. Pry it away.
- Slide the cable assembly out of the bracket after removing the nut that was keeping it there.
- Three bolts inside the door hold the cable arrangement in place (where the cable makes a right angle turn). Remove each of the three bolts.
- Two additional bolts are located underneath the arm that holds the door to the van body. Take them both out. Removing these bolts might be challenging due to the constrained space underneath the arm. Use a 10mm ratchet, an impact driver, or an extension arm for the best results.
- In the bottom corner of the door, there is a pulley system with a Sienna side door release actuator. (The pulley system is in the bottom right corner if you are working on the right door; the bottom left corner if you are working on the left door.) All of the screws keeping it in place should be removed.
- the side door cable assembly should be slid out.
- Reverse the removal process when installing the replacement side door cable assembly.
In This Article...
What does it cost to repair a sliding van door?
A car is more likely to require repairs as it ages. A replacement motor sliding door typically costs between $850 and $1,000.
The sliding door replacement parts make up the majority of the cost. The mechanic must locate auto parts that are specific to the year, make, and model of your car. The parts often cost $807 on average.
Spend some time reviewing your insurance with Jerry and discussing any adjustments while you are having your sliding door replaced. The Jerry app, a registered broker with end-to-end support, can help you switch plans, get reasonable rates quickly, and even cancel an existing policy. The typical user of Jerry saves $879 annually on auto insurance!
What does it cost to replace a door on a Toyota Sienna?
Cost estimation for replacing the power sliding door motor in a Toyota Sienna. Between $1,589 and $1,661 is the typical price range for a Toyota Sienna power sliding door motor replacement. Between $276 and $348 is projected to be spent on labor, while $1,313 is the cost of the parts.
Why won’t the power door on my Sienna operate?
You may be wondering, “Why the heck is this happening? ” when your Sienna side door refuses to open or close.
Several such causes come to mind:
Latch Motor Failure
When you push the button to automatically open the side door, it could occasionally be difficult to open. It frequently makes noise while attempting to open but ultimately failing to do so. The door can only be opened by pulling the handle and holding it for two to three seconds.
This occurs when the latch motor malfunctions, which affects Toyota Siennas pretty frequently. Fortunately, changing merely the latch motor is a quick and affordable fix.
Circuit Overload
A circuit overload is one possibility if your Sienna side door won’t close. When the power sliding door can’t properly latch on, this occurs (due to something blocking it). The circuit for the electric motor will overload, trip the fuse, and prevent the door from fully closing.
You should start with diagnosing this problem because it’s rather simple to do so. Just check to see if the upper and lower tracks are blocked.
What is the cost of repairing a car door that won’t open?
Oh my, that needs to be rectified immediately! Depending on the issue and the kind of vehicle you drive, a car door lock repair will often cost between $200 and $600.
The internal panel of your car door must often be removed in order to replace door locks. Because replacing electronic door locks requires technical components, it’s usually simpler if a mechanic changes them if you’re unclear how to continue.
Car door locks and the appropriate auto insurance are both crucial for keeping your vehicle and the items inside of it secure. The Jerry app can be useful if you’re looking for a new policy.
The Jerry app, a registered broker that provides end-to-end support, compiles reasonable rates, assists you in switching plans, and even assists you in terminating your old policy.
The Toyota Sienna’s sliding door fuse is located where?
The fuse for the sliding doors appears to be in the instrument panel junction box assembly, which is underneath the driver’s side dash.
Why won’t my automated doors open and close?
Doors can stop working as well as they did when they were first installed after some time.
There are several potential causes of an automatic door not opening, including: an electrical or mechanical issue with the drive unit; a motion sensor-activated software mistake; or a door that does not open or close as smoothly as desired.
Additionally, the operation of the doors may make unwelcome noises in conjunction with these issues. a high-pitched squeaking noise, as an illustration. This can be the case because a new part has to be installed or the mechanism needs to be repaired because it is worn out and needs to be disassembled and reassembled.
Another potential problem is when anything blocks the rails that control how the side leaves move, jamming the entrance. Daily checks are necessary to ensure that this does not grow into an issue that cannot be fixed over time.
How can my Toyota Sienna be reset?
In many vehicles, persistent maintenance lights are a regular problem. Typically, there is no electrical issue; instead, your mechanic just neglected to reset the alert after your service was finished.
Just adhere to these simple steps to reset the maintenance required light on your Toyota Sienna:
- Put your ignition key in accessory mode. You shouldn’t start your engine.
- Find the ODO/TRIP button and press it until ODO appears on the display.
- OFFSET your Sienna.
- As you continue to hold down the ODO/TRIP button, turn on your car.
- You have reset the maintenance light when the odometer display shows just zeros.
- Once more, turn off your car.
Your car is not in need of maintenance, so you can drive with a little more confidence now that the maintenance light is off. Check out the Jerry app to see how much you could be saving on auto insurance before you get back on the road.
After you download Jerry, all you need to do is respond to a few questions that will take you around 45 seconds to do, and you’ll get car insurance rates for coverage that is identical to your current plan right away. Customers of Jerry save $879 year on average.
Why won’t my van door open?
Broken connections in the door panel or lock assembly are a frequent cause of the car door lock being stuck in the locked position. The handle, lock cylinder, or interior locking post/switch to the car door latch are a few examples of these. Your automobile door’s complete locking mechanism is disrupted if any of these parts is damaged or detached.
The automobile door may become stuck locked, whether one of these connections is damaged or all of them.
How can you determine if this is the problem? You can try to unlock the stuck door from the inside if you can get in the automobile through a different door.
How does a sliding van door operate?
When a switch in the car or a button on the key fob are pressed, the doors of minivan-style vehicles’ rear passenger doors slide open. Inside the automobile, there may be several switches, but often there is one on each door and one for each door higher up near the driver’s seat. In recent years, auto manufacturers have done away with the door’s buttons in favor of only using the handle to open the door. A notched track on the sliding doors of the car attaches to the car’s frame. A metal rod enclosed in a plastic shell is spun by an electric motor within the door, which subsequently spins the gear. The door’s wiring is allowed to travel with the door because it runs along the bottom of the track. The Chrysler Town & Country featured power sliding doors for the first time in 2001. To prevent the doors from unintentionally closing on someone, there are obstacle detecting systems. The system will stop shutting the door and typically create a sound to warn the driver of the obstruction if it notices a rapid decrease in door speed. This device guards the door from damage and keeps someone from becoming trapped between the door and the vehicle’s frame. These doors are made to be time and effort efficient. Additionally, they assist families who have elderly or disabled members in making the van more usable.
Lubricating:
One approach to fix doors that won’t open from the inside or the outside is to lubricate the door latch. Start by looking for obstruction in the keyway. Open the door and examine the lock assembly to see what is stuck after that. After lubricating the assembly, reposition it. Keep doing this until the obstruction is cleared completely.
Remove The Door Panel:
The door panel can be detached using your tools. It will be simpler to pinpoint the problem once the screws holding the door panel in place have been removed. The electrical connections that are attached to the door panel should then be disconnected. You will discover a plastic cover inside the panel after removing it.
If the door won’t open, take off this cover and check for problems. Now determine if the problem is with the internal shafts or the mechanisms. To make the grip tighter and enable the door to open from the outside, attach a nut to the shaft’s end.
Look for problems with the power locking mechanism to fix the issue of not being open from the inside. It could need to be fixed or replaced.
Finally, double check the door lock motor and inspect the lock assembly for any broken parts. The door panel can be removed to make the entire operation simple.
Get A Locksmith:
If the doors to your car won’t open from the inside or the outside, your lock assembly may be broken. Once we can get the automobile door to open, these problems are simpler to identify and fix.
So, hiring a reputable vehicle locksmith is a straightforward answer to this problem. They can assist in opening the car while minimizing damage to the door. Upon opening the door, lock components can be examined and, if necessary, fixed or replaced.
Why won’t the inside or outside of my automobile door open?
A deadlocked car is almost as awful as having a broken lock. In contrast to deadlocking, this is probably only going to be done on one lock. This problem can occasionally pass for a car key issue, but you can know it’s not the case if the car door won’t open from the inside or the outside. Although it is harsher than some of the more typical auto lockout instances, your locks could experience worse things. You shouldn’t have any trouble getting into the car to fix your locks as long as one of the door locks is functional.
I wouldn’t advise delaying resolution of this matter. You run the risk of getting hurt if you try to open a car door from the inside or the outside by utilizing another door. Poorly made parts are the cause of many cars’ broken locks. Since these components are utilized throughout the entire vehicle, it is only a matter of time before your other locks malfunction, leaving you in a very precarious position.
Solving the Issue
If You Possess the Keys Use your key to unlock the lock that is not broken when a broken lock prevents a car door from opening from the inside or the outside. This level of access will allow you to fix the malfunctioning door lock. It is feasible to simply buy replacement parts for the door lock and fix it yourself, though you probably do not want to.
If you decide to handle this task on your own, use caution when disassembling the door (by removing the panel) in order to access the vehicle’s lock. Verify the connections between the automobile door lock cylinder and the inside locks. If the car door won’t open from the inside or the outside, there is probably a connection problem, therefore look for what has broken. Try to activate the lock from either side while the door is open to determine if the moving parts are not interacting.
If Your Keys Go Missing
In general, you’ll have to get back in your automobile. Ignore the automobile door because it won’t open from the inside or outside. Use your preferred technique to unlock a different automobile door lock. Once you have reclaimed control of your vehicle, you should obtain a new car key and then replace the door lock.
The price of creating a new key as well as the cost of maintaining or upgrading your automobile door lock will be your responsibility. It’s up to you how you approach each of those steps. You have two options: hire a pro or buy the necessary components and try to complete the task yourself. The most important thing is that you get a new key and fix the broken lock.