All Toyota models go through roughly the same oil changing procedure. But oil filters are located in different places depending on the model. You can either consult the owner’s manual or search online to find the location of the oil filter on your Toyota model.
As long as you know where the oil filter is on another Toyota model, you can follow the procedure described below, which is based on the Corolla.
- Lift the vehicle’s front end, and then use jack stands to support it.
- Take off the drain stopper to allow the oil to begin draining.
- The oil filter is located underneath the engine next to the front of the car.
- Take out the oil filter. You can use the oil filter wrench or your hand to complete this. You should use caution because some oil could leak.
- To prepare the area for the new oil filter, wipe it down.
- The new oil filter is screwed on. It’s crucial to avoid overtightening the filter. The filter should be screwed on until the o-ring barely makes contact. Next, manually turn the filter an another 1/4 to 1/2 turn.
- Put a new oil drain stopper in.
- Add fresh oil to the engine and clean up any spills.
- Launch the engine, then look for leaks.
- Dispose of the used oil properly. The law requires all locations that sell oil to take spent oil.
In This Article...
Without the equipment, how do you take out a Toyota oil filter?
Toyota oil filters can be taken out using one of nearly four different techniques. To complete your necessary task in a specific fashion, you are free to choose any of the approaches.
Using Sandpaper
The Toyota oil filter can be removed at a low cost by using sandpaper. You may easily create a tight grip over the oil filter by wrapping the sandpaper over it. After ensuring that your sandpaper is well wrapped, simply pull it in the other direction. The force generated produced by doing so will enable you to remove the Toyota oil filter without the use of a wrench.
Antique timing belt and key
This article also includes another helpful technique that involves the use of a key and an old timing belt. Use both of your tools to make a lever, place the belt over the oil filter, hold it in place with a key, and then unscrew it.
Screwdriver and hammer
To remove the oil, a screwdriver and sledge can also be useful. Basically, you need to place the screwdriver’s tip on the oil channel and use a sledge to pound the screwdriver’s base into the anti-clock bearing. The Toyota oil filter would be easily removed using the sledge’s energy.
Three legs adaptor
A three-legged adapter is another tool used for this design. This adapter is included in what is most likely the best tool for removing Toyota oil filters. For this reason, we may state that this tool is the least used, but in any case, it might provide you with a better result than a wrench.
As a result, if you’re wondering How to Remove Toyota Oil Filter without Wrench, all of these tools and techniques can be used.
There is yet another approach that can be advantageous for removing the oil filter without a wrench. But before attempting any of the other ways, this one should be tried.
The first method to try
Sometimes oil filters are loosely fastened, and you can even use your hand to access a Toyota oil filter. Give it a shot and attempt to open the oil filter counterclockwise. Maybe it’d be simple to open. You should use safety precautions and attempt it for this reason. To open the Toyota oil filter with your hands, keep in mind that gloves are recommended.
We should understand the importance of changing the oil filter after learning how to completely remove a Toyota oil filter without a wrench.
Importance of changing oil filter
The requirement to remove the oil filter in order to replace it is a fundamental phenomenon. In order to preserve the car’s reputation and keep the engine in good shape, it’s crucial to change the oil filter.
Facts to remember
Everyone should be aware of a few crucial details before attempting to remove the Toyota oil filter, both with and without a tool.
Verify that your car is chilly and that it was not in drive mode prior to two hours of work.
Before attempting to remove the filter, re-oil it since occasionally it won’t unscrew if there isn’t any oil on the filter.
You should also be aware of the proper technique for removing the oil filter with any instrument. It would be more tightened rather than becoming loose if you were to remove it in the wrong way.
On a Toyota, which way do you turn the oil filter?
Make sure you’re unscrewing the filter rather than unintentionally tightening it before using any of these methods for filter removal. When gazing up at the oil filter, you must turn it counterclockwise to remove it.
Almost any object having threads that allow tightening or loosening is affected by the proverb “righty-tighty, lefty-loosey” (as it does here).
If the filter moves but doesn’t initially start to loosen up but instead tightens up, it’s your first indication that you’re headed in the incorrect direction. Unfortunately, if you’ve been turning the filter on incorrectly, it might already be stuck.
You might believe that you would personally never turn something around, but when you have to bend down to reach a difficult filter, it’s not as simple as facing the filter directly.
Can you manually remove an oil filter?
With your filter, you’ll be getting up close and personal. Before beginning, put on your gloves and glasses to protect your hands and eyes.
Jack Your Car
If you are unable to reach the filter with the car at a level angle, jack it up. Keep in mind to use caution when doing this and to position the jack correctly underneath the automobile. Once the car is elevated, the jack should be replaced with jack stands.
Position Yourself Carefully
When you have a wrench, it is simpler to avoid lubrication that is dripping. You don’t receive that advantage using the method we’re looking at. Remember to keep your body and face away from the drip zone.
Place Drainage Pan
As usual, position your drainage pan to catch any dripping oil. If there is a spill, you could simply throw some rags under the pan on the floor to prevent damage.
Grab on
Take a firm hold of the end of the filter with your dominant hand. Try to rotate in a counterclockwise direction. Put all your strength behind it.
If it had previously been hand-screwed on by you or your mechanic, it could be possible to remove it without using any further tools.
Which tool is best for removing an oil filter?
- TEKTON Oil Filter Pliers are our Editor’s Choice.
- Oil filter wrench with two-way adjustment from Neiko.
- 2-Piece Rubber Strap Wrench Set from Craftsman.
- Innovative 3-Jaw Oil Filter Wrench with Adjustments
- Oil Filter Wrench Adjustable by Motivx Tools.
- Heavy duty oil filter wrench from GEARWRENCH.
- PVC pliers and a 9″ Channellock Oil Filter.
Finish off with a torque wrench
When you’re done, tighten the filter cap with a 3/8 drive torque wrench. 18.5 ft-lbs of torque is advised (or 25Nm). Never use an impact tool.
Description
The 14-flute design is in accordance with OEM guidelines and is ideal for removing oil filters and cartridge style filter systems from the following vehicles: Toyota Camry V6; Lexus ES, GS, IS, LX, NX, RC, RX; Land Cruiser; FJ; Highlander; RAV4; Tacoma; Tundra; and Venza. The oil filter housing is held in place by a 14-flute wrench, making removal simple and preventing cap stripping. The wrench is engineered to last the lifetime of your vehicle out of sturdy forged aluminum. Its quality greatly beyond that of other wrenches’ standard cast iron and stamped steel. This wrench resists corrosion and rust thanks to a specific anodized treatment finish in gunmetal.
Do you require a wrench for oil filters?
Apply a thin layer of fresh engine oil to the replacement filter’s gasket before manually threading it on. For ease of turning, some filters include a rubberized surface. With just a few excellent hand tightenings, every quality oil filter is built to maintain its seal for tens of thousands of miles. Unless your filter is one of those deeply recessed models with no room for your hands, you don’t need a wrench. (In that scenario, a cap wrench is the only option.) Turn the filter until the mounting plate of the filter feels barely in touch with the filter base. Then turn the screw a further half turn with the wrench.
If it’s been a long since you’ve purchased engine oil, the options could seem overwhelming. See the section below titled “What’s That Starburst?” for some kind advice.
A stripped-out oil-drain plug hole can be saved using this straightforward rubber plug. To install and remove the rod, insert it.
Will WD40 lubricate the oil filter?
Note that in both cases, WD40 can aid in removing the filter. Warming the engine up might also be beneficial before removing the oil filter because the heat should assist the filter come loose. However, only run the engine for a short while, as it could get dangerously hot.
Oil filter thread is it reversed?
Sometimes oil filters can get trapped and look nearly hard to remove. You can start to wonder if you need specific equipment or if the oil filter is broken.
Reverse threads are not present on oil filters. If you’re having trouble removing the filter, try twisting the oil filter cup wrench tool counterclockwise.
We’ll discuss how to prevent your oil filter from being stuck as well as some hints and techniques for correctly installing your oil filter to avoid it fusing. We’ll also examine some of the best tools for unsticking an oil filter.
What direction does a filter turn?
Nothing is more satisfying than doing your own car maintenance. Fortunately, changing the oil is a relatively easy chore that many car owners prefer to perform themselves. But if you’ve never changed your own oil before, you might be unsure of which way to spin the oil filter to take out the old one and put in the new one. We conducted the research to present you the solution for your convenience.
Turn the old oil filter counterclockwise to remove it. Turn the new oil filter clockwise to assemble it.
Don’t worry if you still have some queries concerning the procedure. We’ll go into more information about the subject in this piece. As well as explaining how to remove an oil filter by hand, how to release a tight oil filter, whether hand tightening an oil filter is sufficient, whether you need pre-fill an oil filter, and other topics, we’ll also explain how to loosen an oil filter. Let’s get started without further ado!
What happens if an oil filter is overtightened?
Overtightening the oil filter runs the risk of breaking the O-ring or stripping the threads. If the O-ring is damaged, the filter may not have a good seal, which could eventually lead to oil leakage.
I need a socket for my oil filter, but what size is it?
The head of a fastener, such as a nut or bolt, can be tightened or loosened with a socket wrench. It has a long handle to which various sized sockets can be fitted in order to tighten various sized fasteners. The socket wrench may occasionally have a ratchet handle that enables continuous turning without having to lift the instrument. It’s crucial to select the size socket wrench that matches the specific hardware for each individual project.
There are four standard socket sizes: 1/4 inch (0.6 cm), 3/8 inch (0.9 cm), 1/2 inch (1.3 cm), and 3/4 inch (1.9 centimeters). Additionally, different-shaped sockets are available, including six-point (hexagon), eight-point (double square), and 12-point, to fit different bolt heads (double hexagon). You run the risk of breaking the tool and hurting your hands if you select a socket that is too large. Additionally, certain socket wrenches are deeper than usual to accommodate bolts with protruding threads.
You must choose the right size socket wrench before starting a project, like changing the oil on your car. To allow the used oil to drain from the engine, you must first remove the oil drain plug using a socket wrench. Start the car up first to get the engine warmed up. This makes the oil thinner, enabling smooth drainage. After that, put jack stands under the vehicle, fully engage the parking brake, and switch off the engine. Next, look for the drain plug underneath the car; the hot engine should still have some heat left in it. The drain plug’s nut should be covered by a 3/8-inch (0.9 centimeters) socket, which should be inserted into the socket wrench and turned counterclockwise. The oil drain plug should be simple to open, allowing the used oil in the engine to be drained. To catch all the dripping oil, lay a bucket and some newspaper under the car’s engine.
Oil Drain Plug FAQ
The phrase “universal oil drain plug” is untrue. But there are a few publicly accessible standard sizes that the industry employs.
In many ways, it’s safer to replace it because, if left ignored, a stripped drain plug could eventually cause damage to your engine. To seal it in the interim, you can use welding, such as JB Weld, on the drain plug’s threads, its opening, and both sides of the attached gasket.
Oil drain plugs are quite robust and made to survive for many years, but if they become stripped or begin to leak, they may need to be replaced.
Depending on where you live, oil drain plugs often range in price from $100 to $350. Despite the labor being highly labor-intensive, the part is reasonably priced.