The Toyota Matrix has several trim panels that Toyota has neatly inserted to provide You access, making it relatively easy to take out and change the tail lights. The trim panel at the back of the hatch, which is secured by a tab, needs to be taken off first. Three bolts hold the tail light housing in place once you gain access to it. To separate the three nuts from the three mounting bolts, use a socket or ratcheting wrench. I think they’re 10mm on the majority of model years. You should be able to carefully pry the tail light housing away from the automobile once these are removed. To avoid damaging the electrical connectors, always remember to remove them first.
Toyota matrix tail lights can be removed by removing the two Phillips-head screws holding the tail light in place. Detach the tail light assembly from the back by turning the tail light bulb and plug to the left.
To remove the Toyota matrix tail lights from your Toyota Highlander, open the back hatch and look for the two retaining screws. With a phillips screwdriver, remove the two screws holding the tail light in place. Detach the tail light assembly from the back by turning the tail light bulb and plug to the left.
In This Article...
How is a tail light assembly taken out?
Safety Advice
Always use safety eyewear when performing maintenance on your car. When necessary, put on additional personal protective equipment (PPE), such as latex gloves or closed-toe shoes.
On the back of your car, find the tail light assembly. When you use your brakes or turn signal, they illuminate on each corner.
Remove any mounting screws that are present on the exterior of the tail light assembly, if necessary.
How is a taillight assembly changed?
Replacing a Tail Light
- Step 1: Open the tailgate or trunk.
- Step 2: Remove the tail lamp assembly (if needed)
- Step 3: Remove the bulb.
- Step 4: Insert a replacement bulb after adding bulb grease.
- Step 5: Reattach the component (if needed)
- Repeat step 6 on the opposite side.
How challenging is a tail light component replacement?
Fortunately, changing the tail light bulbs isn’t hard and shouldn’t take you more than 45 minutes to an hour. Be careful that newer models could be a little trickier to disassemble than older ones because there will be more wires.
Can LED tail lights be changed out?
As long as you find the proper one to fit your automobile, replacing your tail lights with LED bulbs is not too difficult. Most LED bulbs can simply be replaced into your automobile, though others may need additional parts to function properly, which I’ll detail below.
Are LED tail lights repairable?
Fortunately, they are simple to replace or repair on your own. Although LED tail lights are built to last, moisture may get inside worn housings and cause circuit boards to corrode, which would lead to the failure of the resistors. This will cause the LED to burn out or cause the light to dim.
How much does a new tail light assembly cost?
Cost of replacing a tail light Expect to pay between $200 and $500 if you elect to have a professional replace your tail light assembly. If you own a high-end luxury or performance vehicle, the cost of the job may increase.
Can the plastic on a tail light be replaced separately?
Hello, and thank you for your letter. The “lenses” or plastic coverings for the taillights are not offered for sale individually. If you wish to do that repair, you will have to buy the full taillight assembly. Now, keep in mind that you might be able to locate one used for a lot less money. In light of this, you should make sure any used parts are either inspected or are of “known good” quality. Junk yards, pull-and-pay shops (where you find and take the part on your own), and even online are common venues to find used units. Make an appointment at your home or place of business with our service department if you require help changing the taillight.
Tail Light Assembly
The group of lights positioned on the back of your car is known as the tail light assembly. They are made up of the reverse lights, brake lights, and tail lights. Each set of lights has a specific function for nighttime conspicuity. The red tail lights are connected to switch on in conjunction with the activation of the front position lighting. When the driver applies the brakes, the brake lights turn on. On both sides of the car, these lights, which are a vivid red, are mounted in multiples of two.
In some vehicles, the brake lights and the tail lights can be merged. They can be placed as a dual-intensity bulb in these circumstances, with the brake-light having a brighter intensity. Fog lights are also used in cars to improve rear sight in heavily foggy conditions. When the driver shifts into reverse to back up the automobile, the reversing lamps turn on. For both your safety and the protection of other drivers, you must make sure the tail lights are in functioning order.
You should replace the tail light assembly if your tail lights have sustained external damage or if the lenses are dim. For every make and model of vehicle, Buy Auto Parts keeps a large selection of tail light assemblies in stock.
We offer excellent aftermarket components as well as original OEM replacements. All of our auto components are rigorously examined and backed by a warranty. Choose the correct year, make, and model of your car from our online catalog to view the components that fit it. You can purchase premium tail light assemblies at Buy Auto Parts for unbeatable pricing, plus free shipping. Contact us by email at [email protected] or over the phone at 1-888-907-7225 if you have any inquiries about our auto parts.