Starting with the car parked and all doors closed will allow you to reset the maintenance light on your Toyota 4Runner. Don’t start the engine after turning the ignition key. You must press the ignition button twice if your SUV has one, but you must not depress the brake pedal as you would if you were starting the car. Depending on the model year, locate the ODOMETER/TRIP button in the instrument cluster and choose either ODO or TRIP A. Press the push button start once or turn the ignition to the off position. When you restart the ignition, press and hold down the ODOMETER/TRIP button one again. If your car has a push-button ignition, press it twice like you did previously. Keep pushing the ODOMETER/TRIP button, and 000000 MILES will eventually show. The service light ought to turn off. To confirm that the reset was saved, switch the ignition to the off position before starting the car.
Turn the ignition on, then set the odometer to “odo” to reset the maintenance light on a Toyota 4Runner. Switch the ignition off. While turning the ignition back on, push and hold the trip reset button.
In This Article...
How To Turn Off the Toyota Maintenance Required Light
The Toyota Maintenance Required Light can be easily reset, albeit the procedure may differ depending on the model year if it hasn’t already been done by your service specialist. Always refer to your Toyota owner’s manual for a detailed step-by-step procedure.
To navigate settings, use the left or right arrow on the steering wheel.
How do I stop the needed maintenance?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
Why does my Toyota state it needs maintenance?
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- If the car is on, turn it off.
- Press and hold the ODO reset / readout button while the engine is off.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- The ODO display will briefly flash before beginning to display only zeros.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Now the light will read “MAINT REQD.”
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
Why, after an oil change, is my maintenance required light still on?
If your oil light continues to illuminate even after changing the oil in your engine, you should examine the sensor to rule out a faulty sensor as the root of the problem. The oil pump might become clogged with dirt and other debris, leading the sensor to mistakenly report oil problems. Although changing the sensor is pretty straightforward, you should take your car to a qualified mechanic if you don’t feel confident doing it yourself. Low oil pressure is the following typical reason. Your oil light will turn on if the oil pressure drops below 5 pounds per square inch. You should check the oil level even though this shouldn’t happen after an oil change because you never know.
Even after an oil change, the final common cause of a lit oil light is perhaps the most troublesome. Numerous engine problems might result from the oil pump not circulating enough oil to maintain the engine’s parts lubricated and operating as intended. Parts do wear down over time, even though getting oil changes at regular intervals should prevent this issue from happening.
What happens after I change the oil in my car?
Reset Oil Change Indicator
- Turn on the ignition.
- Both the stop and accelerator pedals should be fully depressed.
- Maintain firm pressure on the brake and accelerator pedals.
- A notice verifying the reset process is ongoing appears after three seconds.
How can I turn off the Toyota Tacoma’s maintenance is required light?
The convenience of having a car-savvy family member must be incredible! Yes, you can manually reset your light as you are aware that your car is in good condition.
Turn off your vehicle, then push and hold the odometer reset button to turn off the maintenance light on a Toyota Tacoma. Odo/Trip is the typical label for this button. Hold the button down as you restart the ignition of your car.
Your maintenance light ought to be back on now! By starting your car as usual and waiting a few seconds, you can ensure that the light remains off. Visit a professional to ensure that your automobile and your sensors are in good working order if the light does indeed come back on.
Although automobile repairs might be expensive, Jerry can help you save money on other auto-related costs. Jerry is a free insurance comparison software that checks around for the best deals with more than 50 different insurance providers. You may make adjustments at any time, receive prices instantly, and text an agent with any queries you may have. Every year, the typical Jerry user saves $879.
On a Toyota RAV4, how do you turn off the maintenance needed light?
You should switch off the service light if it’s still on after your RAV4 has gotten maintenance. How to reset a maintenance light is as follows:
- Put the ignition on with your key. Turn the key to the first position. This is the position right before the automobile starts.
- On the dashboard, press the reset trip meter button. Hold it down for a couple of seconds. Next, turn your key to the second position.
- Hold the odometer button down for another five or so seconds. The light ought to beep, flash, and then shut off.
- Release the odometer button after it is off. your vehicle off. If the maintenance light on the Toyota RAV4 is still on, only carry out this procedure one or two more times to turn it off.
Get your RAV4 serviced if your maintenance light is still on. Follow your owner’s handbook to learn more about the suggested maintenance schedule for your RAV4 configuration. Maintenance lights can indicate a significant issue.