Turn the key back to the “On position after finding the “trip reset button once more. Hold the trip reset button down until your odometer lights 0 miles. The maintenance light will thereafter go out.
In This Article...
What does a 2009 Toyota Corolla’s maintenance required light mean?
On your dashboard, the Toyota maintenance light may read “MAINT REQD. It’s a light that is always on and alerts you when you require an oil change at a licensed auto shop. Your Toyota will run more smoothly and efficiently if you change the oil in your car.
How do I stop the needed maintenance?
How do I turn the “Maint Reqd” light back on?
- Switch the ignition to the ON position.
- Set the trip display to TRIP A mode on the odometer.
- Activate the OFF position on the ignition switch.
- Turn the ignition switch to the ON position while pressing and holding the Trip Meter RESET button.
- It will do so via the service maintenance reminder light.
On a 2010 Toyota Corolla, how do you turn the maintenance light back on?
Press the odometer button on your dashboard quickly, hold it there while turning the key to the second position. Hold the odometer button down for around 10 seconds. A buzzer sound and the maintenance light should start to flash. The light ought should thereafter go out.
Why, after an oil change, is my maintenance required light still on?
If your oil light continues to illuminate even after changing the oil in your engine, you should examine the sensor to rule out a faulty sensor as the root of the problem. The oil pump might become clogged with dirt and other debris, leading the sensor to mistakenly report oil problems. Although changing the sensor is pretty straightforward, you should take your car to a qualified mechanic if you don’t feel confident doing it yourself. Low oil pressure is the following typical reason. Your oil light will turn on if the oil pressure drops below 5 pounds per square inch. You should check the oil level even though this shouldn’t happen after an oil change because you never know.
Even after an oil change, the final common cause of a lit oil light is perhaps the most troublesome. Numerous engine problems might result from the oil pump not circulating enough oil to maintain the engine’s parts lubricated and operating as intended. Parts do wear down over time, even though getting oil changes at regular intervals should prevent this issue from happening.
Why does my Toyota state it needs maintenance?
- Verify that the odometer’s (ODO) total mileage displaytypically the ‘A’ displayis on.
- If the car is on, turn it off.
- Press and hold the ODO reset / readout button while the engine is off.
- Turn the key in the ignition while maintaining pressure on the ODO button. till the dash lights turn on. Avoid starting the car.
- The ODO display will briefly flash before beginning to display only zeros.
- Release the ODO button once it starts to show zeros, then flip the key back to the “off” position.
- Now the light will read “MAINT REQD.”
What ‘MAINT REQD’ Means
Within 5000 miles of the last reset, the “MAINT REQD” indicator illuminates. It is merely a mileage counter meant to serve as a reminder to the user that an oil change is required and in no way indicates any system failure. If a specialist has always performed maintenance on your Toyota, they reset it after each oil change. It should be noted that the recommended oil change interval is not always 5000 miles. To find out how frequently the oil in your Camry needs to be changed, consult the owner’s manual and your usual technician.
Need Help?
Our service team would be delighted to assist you. Our entire staff of experts is Toyota-certified and adept in resolving even the most challenging problems with your Toyota. Make an appointment right away!
Does the need for maintenance equate to a check engine light?
Some motorists could mistake the check engine light for the service or maintenance necessary light on the instrument cluster. These alert lights are not connected. The service required light simply indicates that the vehicle needs an oil change or other standard maintenance.
On a 2009 Toyota RAV4, how can you reset the maintenance is required light?
- Put your key in the ignition of the RAV4. Set it to the first position. To be clear, the first position is the one in which the car is in before it is started.
- On the dashboard, press and hold the trip meter reset button. Set the second position on your key.
- For ten seconds, keep pressing the odometer button. The light on your RAV4 should flash, maybe beep, and then turn off.
- Release the odometer button after the light is off, then start the vehicle.
- Repeat this procedure to reset the maintenance light on your Toyota RAV4 one or two more times if you see that it is still on. By doing this, you may be sure that your Toyota RAV4’s maintenance light has been successfully turned off.
- You must service your vehicle if you are traveling around Los Angeles and you see the light is still on. A maintenance light may indicate a significant issue. In most cases, your car merely needs an oil change, but it’s still a good idea to visit local Toyota service professionals.
On a 2008 Toyota Camry, how do you turn off the maintenance is necessary light?
Turn the key to position two while pressing and holding the odometer button on the dashboard. When the maintenance light begins to flash, keep holding the odometer button. There may even be beeping sounds. The light ought to dim.
After an oil change, how do I turn off the maintenance light?
In order to start the car, turn the ignition to position one after inserting your key. Turn your key to position two after pressing and holding the trip meter reset button on the dashboard. Hold the odometer button down for a further ten seconds. The light should then begin to flash and potentially beep before turning off.
Why is still on my maintenance light?
Every 4,500 miles, once the maintenance has been reset, the light turns on for around 3 seconds before flashing for approximately 15 seconds. The majority of the time, this merely indicates that your car may need an oil change. After the maintenance data has been reset, the light will turn on and stay on if more than 5,000 miles have been driven.
How to Reset Maintenance Data on Toyota Corolla
You can easily reset your maintenance data. After the necessary maintenance has been carried out in accordance with the maintenance schedule, proceed as follows:
1. Switch the “engine start/stop switch or trip meter-activated engine shutoff a reading appeared,
2. Turn the trip meter reset switch while pressing the “engine switch ON, engine START STOP switch, etc.
3. Hold the button down while continuing to press it until the trip meter reads 000000.
When you understand what each warning light on your Toyota indicates, maintaining it is easy. Never be afraid to call the service staff at Toyota Palo Alto if you ever wonder whether your car needs any type of maintenance. You can ask our helpful staff for assistance in determining what’s wrong with your car and whether you need to schedule a service appointment.