This step-by-step manual is based on Sienna models from 2011 and after. If you have an older Sienna model, you can still try to follow the instructions, but they might not be correct.
Here is how to replace the side door cable assembly in your Sienna without further ado:
- Remove the seat that is most near the broken sliding door. (Optional; it merely provides you with extra space to work on the door.)
- The window on the broken door should be rolled down.
- A hex screw keeping the plastic panel in place is located on the side of the door. Get rid of the screw.
- Reposition the lock so that it is in the open position. (This stops the lock from coming out when the plastic panel is removed.)
- Pry the plastic panel off gently. The panel is held in place by tiny white plastic retaining clips. Make every effort to properly pop them out.
- Pull off the entire plastic panel after closing the door (while still inside the van). Reach behind the panel and unplug the power window connector before you can remove it entirely.
- Once outside, turn your back on the door and lower the window. There is a window molding there. Pull out the window molding after prying off the clip holding it in place. To get it out, you might need to move it back and forth.
- Go to the quarter window in the back. The side door cable is hidden beneath the window by a plastic cover. Pry it away.
- Slide the cable assembly out of the bracket after removing the nut that was keeping it there.
- Three bolts inside the door hold the cable arrangement in place (where the cable makes a right angle turn). Remove each of the three bolts.
- Two additional bolts are located underneath the arm that holds the door to the van body. Take them both out. Removing these bolts might be challenging due to the constrained space underneath the arm. Use a 10mm ratchet, an impact driver, or an extension arm for the best results.
- In the bottom corner of the door, there is a pulley system with a Sienna side door release actuator. (The pulley system is in the bottom right corner if you are working on the right door; the bottom left corner if you are working on the left door.) All of the screws keeping it in place should be removed.
- the side door cable assembly should be slid out.
- Reverse the removal process when installing the replacement side door cable assembly.
In This Article...
Why won’t the power door on my Sienna operate?
You may be wondering, “Why the heck is this happening? ” when your Sienna side door refuses to open or close.
Several such causes come to mind:
Latch Motor Failure
When you push the button to automatically open the side door, it could occasionally be difficult to open. It frequently makes noise while attempting to open but ultimately failing to do so. The door can only be opened by pulling the handle and holding it for two to three seconds.
This occurs when the latch motor malfunctions, which affects Toyota Siennas pretty frequently. Fortunately, changing merely the latch motor is a quick and affordable fix.
Circuit Overload
A circuit overload is one possibility if your Sienna side door won’t close. When the power sliding door can’t properly latch on, this occurs (due to something blocking it). The circuit for the electric motor will overload, trip the fuse, and prevent the door from fully closing.
You should start with diagnosing this problem because it’s rather simple to do so. Just check to see if the upper and lower tracks are blocked.
What does it cost to replace a door on a Toyota Sienna?
Cost estimation for replacing the power sliding door motor in a Toyota Sienna. Between $1,589 and $1,661 is the typical price range for a Toyota Sienna power sliding door motor replacement. Between $276 and $348 is projected to be spent on labor, while $1,313 is the cost of the parts.
How much does a van sliding door replacement cost?
A car is more likely to require repairs as it ages. A replacement motor sliding door typically costs between $850 and $1,000.
The sliding door replacement parts make up the majority of the cost. The mechanic must locate auto parts that are specific to the year, make, and model of your car. The parts often cost $807 on average.
Spend some time reviewing your insurance with Jerry and discussing any adjustments while you are having your sliding door replaced. The Jerry app, a registered broker with end-to-end support, can help you switch plans, get reasonable rates quickly, and even cancel an existing policy. The typical user of Jerry saves $879 annually on auto insurance!
The Toyota Sienna’s sliding door fuse is located where?
The fuse for the sliding doors appears to be in the instrument panel junction box assembly, which is underneath the driver’s side dash.
Why won’t my automated doors open and close?
Doors can stop working as well as they did when they were first installed after some time.
There are several potential causes of an automatic door not opening, including: an electrical or mechanical issue with the drive unit; a motion sensor-activated software mistake; or a door that does not open or close as smoothly as desired.
Additionally, the operation of the doors may make unwelcome noises in conjunction with these issues. a high-pitched squeaking noise, as an illustration. This can be the case because a new part has to be installed or the mechanism needs to be repaired because it is worn out and needs to be disassembled and reassembled.
Another potential problem is when anything blocks the rails that control how the side leaves move, jamming the entrance. Daily checks are necessary to ensure that this does not grow into an issue that cannot be fixed over time.
What does it cost to replace the rollers on sliding glass doors?
For the actual parts, replacing the rollers on a sliding glass door typically costs $20 to $40. Costs for professional labor typically range from $75 to $140. The average price range for rollers, including labor, is between $95 and $170.
How much does it cost to repair a Honda Odyssey sliding door cable?
Best in Automotive Repair Honda Odyssey power sliding door motor replacement generally costs between $1,007 and $1,046. While materials are priced at $857, labor expenses are predicted to range between $150 and $189.
How can a fuse be changed in a Toyota Sienna?
2011-2020 Toyota Sienna SE 3.5L V6 Fuse Replacement
- Locate the engine fuse box and remove the cover.
- Find the fuse that is connected to the problematic component.
- Remove the fuse in question and check to see if it has blown.
- Replace the lid, then lock it down and test the component.
- More details.
The interior fuse box is where?
Under the steering wheel is the inside fuse box. The battery is next to the under-hood fuse box in the engine compartment. The first thing you should look for when something electrical in your car stops working is a blown fuse.
Can automatic doors be manually opened?
Doors with low-energy automatic operators are frequently put in places where, depending on the demands of the person opening the door, they may be opened either automatically or manually. It is frequently more convenient to open the door manually because low-energy operators must open slowly. The question arises because rules and standards only allow 5 pounds of opening force for manually operated, internal, non-fire doors.
“Does an automatic door have to comply with the 5-pound limit when it is operated manually?
The answer to this question is “no,” however there is a conflict you should be aware of. The accessibility requirements have distinct sections for manual and automatic doors. Even though a door occasionally needs to be opened manually, it is still an automatic door if it has an automatic operator.
Here is the passage from the 2010 ADA Standards’ MANUAL DOOR SECTION:
Door and gate opening force is 404.2.9. Fire doors must open with the least amount of force permitted by the relevant regulatory body. Other than fire doors, the following force must be applied to push or pull open a door or gate: 1. Maximum weight for inside hinged doors and gates is 5 pounds (22.2 N). 2. Maximum weight for sliding or folding doors is 5 pounds (22.2 N). The force necessary to release latch bolts or other mechanisms that keep the door or gate closed is excluded from these forces.
There is no restriction on opening force in the accessibility standards’ automatic-door provisions.
The accessibility rules do not restrict the amount of opening force for an automatic door because the 5-pound limit for interior, non-fire-rated doors only applies to manual doors.
This does not imply that an automatic door’s manual opening force is unrestricted. Both manual and automatic doors have opening force restrictions specified by the International Building Code (IBC)*:
Automatic Doors:
The following rules must be followed while using force to unlock doors: 1. For manually operated interior swinging egress doors that are not required to be fire-rated, the force used to push or pull the door open cannot be greater than 5 pounds (22 N). 2. For other swinging doors, sliding doors, folding doors, and doors that must be fire-rated, the door must only be opened with a force of no more than 30 pounds (133 N) and must fully open with no more than 15 pounds (67 N) of force. where the forces are being exerted. Forces must be applied to the door’s latch side.
Autonomous Doors:
As power is used to operate or aid means of egress doors, the design must allow the door to be opened manually to allow passage of the means of egress or closed when necessary to protect the means of escape in the event of a power outage. The forces needed to manually open these doors must not be more than those listed in Section 1010.1.3, with the exception that the force used to move the door must not be greater than 50 pounds (220 N). When a force is given to the door from the side from which egress is effected, the door must be capable of opening from any position to the full width of the opening in which it is installed. Swinging doors, sliding doors, and folding doors operated by power must adhere to BHMA A156.10. Swinging doors that use little energy and those that use power assistance must adhere to BHMA A156.19. Sliding doors that use low energy and folding doors that use low energy must adhere to BHMA A156.38. (For a list of exceptions, see the IBC)
According to the IBC, manually controlled automatic doors may weigh up to 50 POUNDS to initiate movement and 15 POUNDS to fully open. However, the IBC also mandates that power-operated doors must adhere to BHMA A156.10 and that low-energy or power-assist doors must adhere to BHMA A156.19. Because these standards contain stricter criteria than the IBC, here is where the disputes start to appear.
Automatic Doors with Power-Assist Doors or Low-Energy Operators (A156.19):
4.5…Doors must be opened manually with no more than 15 lbf (67 N) to release a latch, 30 lbf (133 N) to start the door moving, and 15 lbf (67 N) to fully open the door, if one is there. The forces must be exerted one inch (25 mm) away from the door’s latch edge.
Doors with motors (A156.10):
10.2.8 A swing door must be able to be opened manually in the case of a power outage with a force of no more than 30 lbf (133 N), exerted 1 in. from the edge of the lock stile.
10.2.9 Swinging doors with breakaway devices must only be opened by applying 50 lbf (222 N) of force one inch from the edge of the lock stile. Powered operating elements other than spring power are not permitted to operate the door(s) when they are opened in the break-out mode.
- The IBC and the accessibility standards limit interior, manually operated swinging doors that are not fire-rated to a weight of 5 pounds.
- manually controlled swinging doors that are fire-rated
- The door requires 30 pounds to move and 15 pounds to fully open, according to the IBC. For outside fire doors, NFPA 80 advises using a size-4 closer, and for interior fire doors, a size-3 closer.
- manually controlled swinging doors on the exterior
- According to the IBC, or as permitted by state and municipal standards, the door requires 30 pounds to move and 15 pounds to be fully opened.
- doors with power-assist or low-energy operators
- According to BHMA A156.19, which is more stringent than the IBC, the door must be moved with 30 pounds and must be fully opened with 15 pounds.
- pedestrian doors with motors
- With the exception of 50 pounds if the door contains a break-away function as required by BHMA A156.10, which is more stringent than the IBC, doors must weigh 30 pounds to move and 15 pounds to open fully.
Remember that the codes and standards mentioned here might not match local or state requirements.
The limitations mentioned in the accessibility standards would apply instead of the less stringent requirements of the building code where the accessibility standards include a more strict requirement (such as the 5-pound limit on inside, non-fire-rated, manually-operated doors).
What is the price of automated sliding doors?
In the US, an automatic door will cost, on average, $2,122.80 in 2020; expenses can range from $1,458.25 to $2,787.35.
Depending on the type of opener, where it is installed, and any optional accessories you select, the price will vary. It is not a question of whether or not you should automate your business for public accessyou shouldbut rather, how you can afford to do so. For many small enterprises and individuals, it has always been a problem. The other concern is what kind of automatic door you should be looking into to make your establishment accessible to the disabled or just to people who have dogs, senior citizens, packages, or just want to.