A password must be entered in order to access the administrator menu, which is generally off-limits to general operators, before the Toyota forklift maintenance light may be reset. The maintenance hour meter can be set from this menu.
Certain combinations must be entered in the dashboard display below in order to accomplish these tasks. The four buttons have been assigned the letters A through D for ease of reference throughout these instructions. Before attempting to complete the procedure, it could be beneficial to become familiar with these guidelines.
In This Article...
Entering the administrative password:
1. Hold down buttons B and D at the same time for two seconds. Both at the start of the 2 seconds and at the conclusion of the 2 seconds, a brief beep should be heard.
2. In less than 10 seconds, press button C. There should be one more beep. Within 10 seconds, do this again by pushing button C, and you’ll hear another little beep.
3. Press and hold buttons B and D simultaneously for 2 seconds within the next 10 seconds. When B and D are first pressed, a brief beep is heard like before, but after 2 seconds, several more brief beeps are heard. The administrator’s menu ought to appear.
An illustration of what the administrator menu might look like is displayed above. The buttons A, B, and C move from one list of options to the next, while the button D selects a setting and takes the user to that setting’s specific screen.
Resetting the maintenance hour meter:
1. Use button D to pick the setting “MAINTENANCE HR” after finding it. It should resemble the menu on the right.
2. The operations of buttons A through D are used to set the maintenance hour meter’s time. When Button A is held down for more than two seconds, the selected value is reset to 0. Button B decreases the meter’s set time, Button C raises the meter’s set time, and Button D brings up the administrator menu.
NOTE: From 10 to 200 hours, time can be changed in 10-hour intervals. From 200 hours to 2000 hours, it can be set in 50-hour increments. It can’t be set to less than 10 or more than 2000 hours.
Locking the operator setting menu (DX model only):
1. Find the location “Use button D to select MENU LOCK.
2. Locking this menu restricts the setting values that normal operators can modify. preparing to “Choosing YES will stop the operator’s setup menu from appearing. The administrator menu screen is displayed when Button D is pressed, and Button B picks “YES, Button C selects “NO.
We also recommend reading our post on how to perform simple forklift maintenance.
How can a forklift error code be cleared?
A: The procedure for clearing codes on Caterpillar and Mitsubishi forklifts is extremely exact. Before attempting to clear forklift codes, it helps to be familiar with these procedures. Additionally, it is advised that you use a stopwatch to time yourself precisely since many tasks must be completed in specific amounts of time before moving on to the next. These stages are intended to be visually presented in the diagram. Be patienteven skilled Caterpillar and Mitsubishi forklift mechanics occasionally make mistakes when performing these steps!
1. At the same time that the forklift key switch is turned on, start the stopwatch. Don’t step on the gas pedal.
2. Push the forklift accelerator five times in three seconds.
with the pedal being released to complete the set of five. You have five seconds to do this. You run the risk of never clearing the codes if pressing the accelerator five times in a row takes longer than five seconds.
3. After waiting for seven seconds, hit and hold the accelerator for at least ten seconds until the malfunction indicator light begins to flash.
4. Immediately let go of the gas pedal. This launches a self-diagnostic test, and one or more blinking forklift DTC codes will appear on the dashboard display.
5. Let the pedal rest for at least 10 seconds.
6. For 10 seconds or longer, press and hold the accelerator. By doing this, the forklift codes are successfully cleared and the findings of the self-diagnostic test are deleted. On the dashboard, only the current hour meter will be visible; there shouldn’t be any codes.
What does a Toyota forklift’s wrench light signify?
I’m here. The computer uses the wrench light as a warning to the driver that there is a problem with the engine or transmission and enters limp mode when it comes on. To make the light turn on, you would need to have the computer checked to discover what might be wrong with the engine. While waiting, make sure that every sensor and switch on the engine and transmission is plugged in and check all of their connections. Without knowing where to begin without first examining the codes, there are too many locations to check. If the wrench light is still on and you need more help, get in touch with a specialist, like one from Your Mechanic.
What does the forklift code F 16 mean?
F16 indicates that the computer received the identical signal from both directions for more than 2 seconds. Was a backup alarm installed? You could inspect the wiring from the directional switch to the ECM “pin to pin.”
How do you reset a Clark forklift’s code?
the ECU’s code-flashing function. by a solitary, three-second flash. switched OFF. cycle the foot pedal by pushing it all the way to the floor and then fully releasing it.
What does the forklift code E 30 mean?
ECCS C/U Error signal, code E30. Either the ECM receives no power or perceives a low voltage source. – The ECM received no, little, or a lot of electricity.
What does the forklift code E 38 mean?
It alludes to the fuel pressure sensor detecting unusually high fuel pressure. DTC E-38 may be set when the fuel pressure in the fuel piping or hose has been abnormally high for a predetermined period of time, according to additional troubleshooting information.
What does it imply when a wrench flashes?
hello Robert We appreciate your contacting us tonight. The wrench light is an alert or service light that shows that the car needs a regular maintenance checkup. This is very typical around 150,000 miles and frequently means a transmission fluid service is overdue. The symptoms you are describing are also frequently caused by polluted transmission fluid or debris jammed in hydraulic lines. However, a torque converter that is worn out or broken will also frequently exhibit the same symptoms. A professional technician should probably visit your location to perform a warning light inspection so they can download the stored codes, figure out why the light is on, and decide what services or repairs need to be done to remedy your problems.
Toyota, why does my security light flash?
Security Symbol When the key is taken from the engine switch, this indicator light flashes to show that the system is in operation. When the registered key is placed into the engine switch, the indicator light stops flashing, signaling that the system has been disabled.
When the wrench light is on, can you drive?
Why is there a wrench light? These two symbols both denote that your car requires maintenance. Usually, it’s because a deadline-based milestone was missed or the car has a problem that requires professional repair.
What is the E250 code?
Congenital adrenogenital diseases associated with enzyme deficiency (E250) – ICD 10 Diagnosis Code – Market Size, Prevalence, Incidence, Quality Outcomes, Top Clinics & Doctors.
How are codes removed from a P5000 CAT forklift?
I wrote something in crayon on this topic, referring to the “Pedal Dance” in discussion 6842. With the accelerator pedal removed, turn the ignition on. Three seconds later, fully depress the accelerator pedal five times in five seconds (end in released position).