Since the sensor is typically just replaced when it breaks, cleaning an oxygen sensor on a Toyota Corolla is not an usual activity. If you cannot afford a replacement sensor, you can clean the sensor as a temporary workaround. There is no assurance that cleaning the sensor will make it functional once more or that your check engine light will turn off and the emissions system’s fault messages will stop being generated. The sensor could become irreversibly damaged if it is cleaned. The oxygen sensor on a Corolla can be cleaned, however it’s a last resort.
In This Article...
Step 3
The O2 sensor’s electrical plug should be unplugged. Both before and after the catalytic converter is a sensor. By drawing the plug out of the O2 sensor and depressing the release tab on the plug, you can remove the electrical wiring.
Step 5
Holding the oxygen sensor in place with vice grips, warm the sensor’s end with a propane torch until it begins to glow slightly red or orange.
Step 6
After heating the oxygen sensor, immerse the hot tip in a pail of ice water. The carbon deposits that have accumulated on the sensor will be broken up by this procedure.
Once more, carry out steps 5 and 6, and after that, let the sensor cool completely before reinstalling it. Removal is the opposite of installation.
Is the oxygen sensor reusable after cleaning?
An essential component of your car’s pollution control system is an oxygen sensor. Simply explained, an oxygen sensor measures the amount of emissions your automobile emits and transmits that data to the management computer in the engine. There are at least two sensors in your car, and when one of them malfunctions, you need to take action. Can an oxygen sensor be cleaned? Contrary to what you may have heard or read, such sensors should be changed when they malfunction.
Locating Your Oxygen Sensors
A malfunctioning oxygen sensor is likely to go undetected until an emergency code displays on the dashboard. If not, your automobile can perform poorly and lose significant amounts of fuel.
Depending on the engine type, different numbers of oxygen sensors are present. Two sensors are often included on transverse four-cylinder engines. The one is upstream, and the other is downstream. Each inline four-cylinder engine, inline six and V6 engine, and inline eight engine has three sensors, one on each engine bank, and a third downstream. Four sensors are present on transversely mounted V6 and V8 engines, one on each bank, one downstream, and one at the back of the engine.
One defective oxygen sensor is all that is required for your car to experience issues. You must therefore determine which sensor is broken.
Replace, Don’t Clean
You could have discovered instructions for cleaning an oxygen sensor online. These instructions typically go into great depth, including how to gently remove the sensor, use a cleaning solution, and put the unit back where it was.
This information is false, though, as oxygen sensors are made to be replaced, not cleaned. No automaker encourages cleaning of sensors. In fact, if you attempt to clean a sensor and something goes wrong later, you always run the risk of voiding a warranty. Here’s how to replace an oxygen sensor if you discover that your automobile has a bad one.
Test Your Oxygen Sensor
One option is to evaluate the efficacy of oxygen sensors. A digital voltmeter and back probe are utilized to make this work. Start the car after the nearby wires have been examined and eliminated as a potential issue, and let it run until the engine exhaust temperature reaches at least 600 degrees Fahrenheit.
Then, a predetermined number of points are measured under predetermined circumstances using the voltmeter and back probe. As you might expect, oxygen sensor testing frequently requires the services of skilled mechanics. Additionally, doing this will guarantee that the right malfunctioning oxygen sensor is found and replaced, saving you money.
Can an oxygen sensor be cleaned? Technically speaking, you can. However, as the component is designed to be replaced when a problem emerges, it is not advised. Cleaning an oxygen sensor is more labor-intensive than replacing the part, and after finding the part and making sure it is functioning properly, replacing it adds security for the future.
View the complete selection of relays, sensors, and switches on NAPA Online or depend on one of our 17,000 NAPA AutoCare locations for regular servicing and repairs. Consult an informed professional at your nearby NAPA AUTO PARTS store for more details on how to replace your car’s oxygen sensors.
O2 sensor cleaning with fuel injector cleaner?
The simple answer is that B-12 Chemtool Total Fuel System Clean-Up (part #2616), our strongest gasoline fuel additive, and a thorough tune-up might help you out.
True oxygen sensor cleansers that are secure to run through your engine don’t exist. We do not advise trying to clean O2 sensors, even if some users choose to remove them and use a wire brush or an aerosol cleaner to remove deposits.
We believe their function is too important to risk the sensors being harmed and inadvertently (and mistakenly) changing the air-fuel ratio. The threads on the sensor(s) might not be able to withstand repeated removal and installation cycles. They occasionally don’t even make it through an entire cycle!
What About My Catalytic Converter?
You cannot directly clean a catalytic converter while it is still attached to the vehicle because anything that may be safely put through the engine will be transformed to CO2, O2, and N2, none of which will perform any cleaning. A “catalytic converter cleaner” is therefore gimmicky. You do, however, have a few choices.
Catalytic converters should actually last the lifetime of the vehicle since, under certain circumstances, they “self-clean.” If the “guts” are physically intact and the catalysts only have a slight buildup, you can:
What leads to the failure of an oxygen sensor?
What Leads to the Failure of an Oxygen Sensor? O2 sensors can malfunction as a result of contamination from things like coolant and oil ash. O2 sensors can occasionally stop working for no apparent reason. Other times, contaminants like oil waste and coolant can cause an O2 sensor to malfunction.
How can you know if an oxygen sensor is malfunctioning?
Symptoms of a Faulty Oxygen Sensor
- Check engine light that is illuminated. If you have a malfunctioning oxygen sensor, your dashboard’s bright orange Check Engine light will often glow.
- poor gas mileage
- A rough-sounding engine
- Failure of the Emissions Test.
- a more aged vehicle.
Will performance improve if the O2 sensor is changed?
Further inspection is always necessary because an illuminated check-engine light may indicate either a simple problem, such as a loose gas cap, or something more significant, such as a problem with the catalytic converter. However, it can be an indication of an issue with your O2 sensor or possibly another component of your exhaust or emissions system. Your check-engine light should be readable by any repair business, and a mechanic or auto parts retailer may do this at no charge.
A rough idle, misfiring spark plugs, a lack of power, stalling, or a considerable rise in fuel consumption are further indications that you need a new oxygen sensor. The EPA claims that changing a defective oxygen sensor can increase fuel efficiency by as much as 40%, so obviously that is one place to look if your car starts to use more petrol. However, same symptoms could also be signs of other issues. A broken O2 sensor may also be to blame if your car fails an emissions test.
Without factoring in labor, the price of a new oxygen sensor can range from less than $100 on some models to $300 or more on others. This is because labor costs depend on where the sensors are positioned in the vehicle. As a result, depending on the type of vehicle you drive, the total cost of oxygen sensor replacement may differ significantly.
Symptoms of a Bad Oxygen Sensor
First and foremost, it’s crucial to realize that an OBDII code by itself does not indicate that an oxygen sensor has failed. Sensors merely provide data. For instance, an oxygen sensor that detects a lean fuel combination will undoubtedly trigger a code. There is no need to replace this sensor because it is functioning properly.
There are various OBDII codes in particular that will be activated if a malfunctioning or dead sensor is the problem (more on this in the following section). A malfunctioning sensor will thus frequently cause the car to physically exhibit the symptoms.
A drop in fuel economy may be a clear indication that an O2 sensor is not functioning properly. A gasoline combination that is either too low or too rich can produce this.
A/F ratio swings of this magnitude indicate a malfunctioning upstream or control sensor. The downstream or diagnostic sensors won’t result in such a problem because they just keep track of the exhaust leaving the catalytic converter.
Additionally, a misfire, a rough idle, and/or hesitancy when attempting to accelerate are signs of a malfunctioning oxygen sensor. However, keep in mind that these problems might also have unrelated root causes that have nothing to do with an automobile’s oxygen sensors. Therefore, none of them by themselves would be sufficient to replace one. It is frequently necessary to combine an OBII warning with engine performance difficulties and a physical examination of the sensor in order to reach an accurate diagnosis.
Common O2 Failure Causes
Three main causes of oxygen sensor failure are age and heavy mileage, an internal pollutant (poisoning), or an electrical problem.
Every 30,000 miles, one or two wire unheated oxygen sensors should be checked or replaced. These sensors are made to allow a significant volume of exhaust to come into touch with the active ceramic element because they are totally dependent on hot exhaust gas to reach their operational temperature.
Due to their internal heat source, heated oxygen sensors can be put much farther downstream than unheated sensors, making them less susceptible to contamination. Every 60,000 miles, heated sensors should be checked out or replaced. While heated oxygen sensors can be used in locations that are safer than unheated versions, they contain numerous circuits that make them susceptible to electrical problems. A sensor won’t work properly if the heater circuit in it malfunctions. In fact, heater circuit problems are a frequent cause of OBDII codes.
All oxygen sensors must be exposed to a continuous stream of hazardous exhaust gases, intense heat, and high velocity particles in order to function. As a result, their effectiveness will unavoidably decline over time.
Oxygen sensors may become tainted with substances from the engine. Leaded gasoline and exhaust from an excessively rich fuel mixture might contaminate an O2 sensor. The similar result may be obtained from silicone or antifreeze residue left over from damaged gaskets. The sensors shown below need to be replaced since they have been contaminated.
Numerous sensors degrade frequently as a result of carbon buildup from a heavy fuel mixture. This could be caused by a number of things, such as a blocked air filter or a fuel injector that is leaking or broken.
If antifreeze gets into the combustion chamber, it can seriously damage a sensor. This may occur as a result of an intake manifold gasket leak, a leaking cylinder head gasket, or a warped or cracked cylinder head.
An oxygen sensor’s head can turn white due to silicone poisoning, as seen in the image on the left. The use of an inappropriate silicone gasket sealant on the engine is the most frequent cause of this issue.
An oxygen sensor will suffer if inappropriate (leaded) fuel is used. Even though this is a rare event, it is useful to understand how leaded gasoline affects sensors.
The oxygen sensor will not come out.
Use a strong penetrating lubricant to thoroughly coat the sensor thread region. By heating up the bung, starting and revving the engine should help to further loosen the sensor. Try an O2 socket if you are currently using an open end wrench. If that doesn’t work, try using your socket and a long ratchet or breaker bar to produce greater torque. If the problem persists, heat the bung with a torch until it turns cherry red, then remove the sensor. Use a thread cleaner to clean the bung threads after the sensor has been removed. The threads may need to be mended in some circumstances. A thread repair kit (Walker Part # 88-832) can be used for this. Never remove an O2 sensor with an impact wrench because you risk stripping the threads in the bung. Walker carries a full line of oxygen sensor bungs and plugs in case a problem arises that calls for the replacement or addition of a bung.
Are the rear oxygen sensors really necessary?
The function of the downstream sensors is to keep an eye on the catalytic converter’s performance and overall health. Removing them will disable this function and result in a malfunction indication light (MIL) or CEL (check engine light) on the car.
I am getting a CEL/MIL and a . . . code. Do I need to replace the oxygen sensor?
No, not always. The data that the oxygen sensor collects is simply reported. For instance, you can have a vacuum leak or a bad fuel injector if you receive a lean mixture code. The oxygen sensor cannot be replaced to resolve this issue. You’ll simply receive the same code once more.
Do I need to replace all of the sensors at once?
O2 sensors should ideally be changed in pairs. For instance, you should replace the downstream right sensor if you replace the downstream left sensor.
On the majority of cars made after 1996, the ECU will set a code for the other sensors if one sensor is replaced, particularly the front engine monitoring sensor. This is due to the fact that new sensors switch activities considerably more quickly than do older, more seasoned sensors. On the majority of vehicles, the code is likely to be set between 30 and 60 days AFTER the first sensor replacement.
What is the life expectancy of an oxygen sensor?
Every 60,000 miles for heated oxygen sensors and every 30,000 miles for unheated oxygen sensors, respectively, should be the time for inspection or replacement.
How can I test an oxygen sensor?
By first locating the signal line on the sensor, you may test the O2 sensor in a car. The voltage will also oscillate between 200 and 800 millivolts, or.2 to.8 volts on your meter, when you use a voltmeter with the scale set to 1 volt. Your sensor has failed if the reading is stuck in one place or switches unusually high or low. It is important to have your vehicle tested at a reputable facility if your results are ambiguous.
A second approach is to directly link some of the several testers on the market to the oxygen sensor. Although this method is less precise, it can identify some sensor malfunctions.
What is a California emissions sensor? How do I know if I need one?
A California emissions O2 sensor is intended for automobiles built to comply with California emission standards. A sticker identifying these vehicles ought to be placed on the driver’s door jamb or beneath the hood.
What are the symptoms of a failing oxygen sensor?
A faulty sensor will typically result in low gas mileage, stalling or reluctance, and a CEL/MIL. The oxygen sensor is not the only reason for these symptoms, though.