You might be asking why the recommended amount of oil has a range. The quantity of oil you pour back into your crankcase will vary based on a number of variables, including how much oil drains, whether or not you have an oil cooler, and a few more. For this specific oil change, for instance, I had to add nearly 7 quarts of oil to get the oil level dipstick to register the correct quantity. Over 6 quarts have been added by others. Enough said. Aim for at least 6 pints, but be ready with 7.
The final word? Add oil until the second marking or divot is covered by oil on your dipstick.
A piece of advice: Avoid wasting money on 1-quart containers. Compared to buying in bulk, they are much more expensive. You should buy two 5-quart containers, but 12-quart containers are also available online and at some stores. Filters operate in a similar manner. Buy in quantity!
The MotivX Tools oil change kit, which was described before, is an optional component of this oil change. Are you in need of this kit? No. Does it make your life much easier and is it incredibly convenient? Yes, indeed! Everything you could possibly need is in the kit. An oil filter wrench, a drain tool, and an oil funnel set are all included in the kit.
In This Article...
Step 1. Remove Engine Skid Plate
Make sure your car is on level ground before you start. This will guarantee that you completely drain the old oil and replace it with as much new oil as you can.
The oil filter and drain plug are found in the bottom of the engine in the third-generation Tacoma.
The fact that you have to take off your skid plate in order to change the oil is a little inconvenience.
The front two are visible above. The front bolts should be loosened by using your 10mm socket.
When all four bolts are loose, brace the skid plate (which isn’t very heavy) and take out all four bolts at once. Even without the four bolts you just removed, the skid plates are held up at the front by two tabs, which keep it from falling.
Move the skid plate so that it is off to the side after detaching it from the tabs.
Step 2. Drain Old Oil
It is located directly between the engine skid plate’s smaller section and the cross-member. For this one, you’ll need a 14mm socket.
You’ll need to release the pressure inside the crankcase because the engine compartment is essentially a sealed system in order to facilitate a quicker and more effective oil drain.
Unscrew your oil cap and set it aside before you completely unfasten the drain plug. After completing that, proceed to removing the drain plug bolt. Make sure your oil collect pan is positioned underneath the bolt.
Be cautious if you’ve just run the motor! You risk being burned by the oil, which is about 200 degrees Fahrenheit.
You’re advised to put on gloves to prevent coming into contact with the oil on your skin too much.
As a side note, the oil pours out faster and with more force than you may expect.
As was mentioned earlier, if you’re not prepared, you might mess things up. Take your time to avoid any problems.
A fellow do-it-yourselfer told me to keep the engine oil fill cover on until the flow has noticeably decreased to avoid this rush of oil and any potential problem. The cap is then opened to let the pressure out. Regards, Paul.
Once all of the oil has been completely removed, grab the replacement gasket that was provided and reinstall the bolt.
Personally, I use feel to tighten the bolt. Toyota advises applying 30 ft/lbs of torque to the bolt. Consider installing a Fumoto Valve to make life even simpler for you and the next oil change. I was unable to order one in time, but I will swap one in during the subsequent oil change to save time and minimize mess.
How frequently should the oil filter be changed in a Toyota Tacoma?
For standard oil, Toyota advises changing your 2021 Toyota Tacoma’s oil and filter every 3,0005,000 miles. Changing synthetic oil should be done every 7,500 to 10,000 miles. Remember that the easiest way to find out the appropriate intervals for your car is to consult the owner’s manual and your dealer.
How much oil does a 2018 Tacoma require?
For instance, a 4-cylinder engine needs at least 5 quarts of oil, whereas a 6-cylinder engine needs about 6 quarts.
How is the oil filter on a Toyota Tacoma loosened?
On the engine’s lower right side is where the oil filter is located. With a wrench, turn the filter in the other direction to remove it. As you crank the wrench in a counterclockwise direction, it automatically tightens around the filter. If removing the filter is challenging, use force.
Without the equipment, how do you take out a Toyota oil filter?
Toyota oil filters can be taken out using one of nearly four different techniques. To complete your necessary task in a specific fashion, you are free to choose any of the approaches.
Using Sandpaper
The Toyota oil filter can be removed at a low cost by using sandpaper. You may easily create a tight grip over the oil filter by wrapping the sandpaper over it. After ensuring that your sandpaper is well wrapped, simply pull it in the other direction. The force generated produced by doing so will enable you to remove the Toyota oil filter without the use of a wrench.
Antique timing belt and key
This article also includes another helpful technique that involves the use of a key and an old timing belt. Use both of your tools to make a lever, place the belt over the oil filter, hold it in place with a key, and then unscrew it.
Screwdriver and hammer
To remove the oil, a screwdriver and sledge can also be useful. Basically, you need to place the screwdriver’s tip on the oil channel and use a sledge to pound the screwdriver’s base into the anti-clock bearing. The Toyota oil filter would be easily removed using the sledge’s energy.
Three legs adaptor
A three-legged adapter is another tool used for this design. This adapter is included in what is most likely the best tool for removing Toyota oil filters. For this reason, we may state that this tool is the least used, but in any case, it might provide you with a better result than a wrench.
As a result, if you’re wondering How to Remove Toyota Oil Filter without Wrench, all of these tools and techniques can be used.
There is yet another approach that can be advantageous for removing the oil filter without a wrench. But before attempting any of the other ways, this one should be tried.
The first method to try
Sometimes oil filters are loosely fastened, and you can even use your hand to access a Toyota oil filter. Give it a shot and attempt to open the oil filter counterclockwise. Maybe it’d be simple to open. You should use safety precautions and attempt it for this reason. To open the Toyota oil filter with your hands, keep in mind that gloves are recommended.
We should understand the importance of changing the oil filter after learning how to completely remove a Toyota oil filter without a wrench.
Importance of changing oil filter
The requirement to remove the oil filter in order to replace it is a fundamental phenomenon. In order to preserve the car’s reputation and keep the engine in good shape, it’s crucial to change the oil filter.
Facts to remember
Everyone should be aware of a few crucial details before attempting to remove the Toyota oil filter, both with and without a tool.
Verify that your car is chilly and that it was not in drive mode prior to two hours of work.
Before attempting to remove the filter, re-oil it since occasionally it won’t unscrew if there isn’t any oil on the filter.
You should also be aware of the proper technique for removing the oil filter with any instrument. It would be more tightened rather than becoming loose if you were to remove it in the wrong way.
How often should I have my 2018 Toyota Tacoma’s oil changed?
How often should an oil change be performed on a 2018 Toyota Tacoma? One of the most crucial and important services for your car is an oil change. For traditional oil, Toyota advises having your 2018 Toyota Tacoma’s oil and filter replaced every 3,000 to 5,000 miles. Typically, synthetic oil needs to be changed every 7,500 to 10,000 miles.
Where is the oil filter?
What location does the oil filter have? Different cars have different locations for the oil filter. It is frequently only reachable from below and may be protected by the undertray, which must first be removed. On some automobiles, the filter is accessible from above.
Is synthetic oil required for Tacoma?
Your Toyota Tacoma will operate smoothly if you maintain your oil changed on a regular basis and use the right oil. The Toyota Tacoma runs on 0W-20 and 5W-20 oil viscosities. The best engine cleaners minimize sludge buildup and keep your engine operating smoothly for longer.
What type of oil does Toyota suggest for the Tacoma?
High Mileage 0W-20 Full Synthetic Motor Oil, 5 Quart, from Mobil 1. (Part No. 15015) Product attributes: For engines with more than 75,000 miles, Mobil 1 High Mileage full-synthetic motor oil 0W-20 is made to allow up to 10,000 miles between oil changes.
How much fuel can a Toyota Tacoma hold?
The 3.5L (211 ci) V6 engine holds 6.1 quarts, whereas the 2.7L (164 ci) 4 cylinder engine stores 6.2 quarts (6.2 with a tow package). Fortunately, we’ll go over the importance of synthetic oil for your 2019 Tacoma as well as what other Tacoma owners are saying about truck maintenance.