The initial actions are
In This Article...
What size oil filter housing does a Toyota have?
The size of the 14-point hex ring on top of the oil filter housings appears to be misunderstood.
Regarding the size of the top 14-point ring, there is information out there that claims there is both a 65mm and 65.5mm housing.
The size of each oil filter housing is 64.16mm. The diameter is referred to as 64mm for the sake of simplicity.
How often should the oil be changed in a Toyota Highlander?
One of the most fundamental and important maintenance for your car is an oil change. For conventional oil, Toyota suggests changing your 2021 Toyota Highlander’s oil and filter every 3,000 to 5,000 miles. Normally, synthetic oil needs to be changed every 7,500 to 10,000 miles.
Exactly how much oil does a Toyota Highlander require?
These guidelines were developed using an oil change on a 2018 Highlander XLE 3.5L V6. While you can apply the fundamentals to different models and years, you should always reference your owner’s handbook for details particular to your car.
Warm up the engine
Start your engine and let it run for a while in cold weather to thin out the air and improve oil flow. A level space is recommended for parking your Toyota Highlander. Once the engine has warmed up, shut it off.
Drain the old oil
The drain bolt can then be removed by crawling underneath your Highlander. Allow the oil to drain for at least 15 minutes into your drain pan or another suitable container.
To stop leaks, replace the washer in your drain bolt. The oil drain bolt should then be installed once more and tightened.
Remove the filter
A 2018 Toyota Highlander’s oil filter is located underneath the vehicle. Utilizing the Toyota Highlander oil filter wrench, remove the filter housing. Take off the O-rings and old filter from the housing. Verify that the engine surface is free of any adhesion to the filter gasket.
Install the new oil filter
Before installing the replacement filter, clean the engine block of any debris and residue. Place the replacement filter and O-rings inside the housing after lubricating them.
Put new oil in the engine
5.8 quarts of engine oil should be poured into the oil fill hole. Start the engine after replacing the fill cap and making sure it is properly screwed in. Time you let the engine run for a while, look for leaks from the oil filter and drain bolt.
Stop the engine and check the oil level
Stop and wait for three minutes after running the engine for a while. Check the oil level with the dipstick and add extra if necessary.
Dispose of the old oil according to regulations
Never dispose of used oil in the trash or on the ground. The environment could be harmed if this is done. The majority of states require businesses that sell motor oil to accept your used oil, as do service centers and establishments that change oil (like Jiffy Lube). For information on additional locations to recycle your oil, consult the websites of your state or municipal government.
The Toyota Highlander model year 2015 requires how many gallons of oil?
The two engine choices, together with the quantities of oil required for each, are as follows: Oil for a 2.7 liter engine must fill 4.6 quarts. Oil for a 3.5 liter engine must fill 6.4 gallons.
How can a Toyota oil filter be removed without a wrench?
Toyota oil filters can be taken out using one of nearly four different techniques. To complete your necessary task in a specific fashion, you are free to choose any of the approaches.
Using Sandpaper
The Toyota oil filter can be removed at a low cost by using sandpaper. You may easily create a tight grip over the oil filter by wrapping the sandpaper over it. After ensuring that your sandpaper is well wrapped, simply pull it in the other direction. The force generated produced by doing so will enable you to remove the Toyota oil filter without the use of a wrench.
Antique timing belt and key
This article also includes another helpful technique that involves the use of a key and an old timing belt. Use both of your tools to make a lever, place the belt over the oil filter, hold it in place with a key, and then unscrew it.
Screwdriver and hammer
To remove the oil, a screwdriver and sledge can also be useful. Basically, you need to place the screwdriver’s tip on the oil channel and use a sledge to pound the screwdriver’s base into the anti-clock bearing. The Toyota oil filter would be easily removed using the sledge’s energy.
Three legs adaptor
A three-legged adapter is another tool used for this design. This adapter is included in what is most likely the best tool for removing Toyota oil filters. For this reason, we may state that this tool is the least used, but in any case, it might provide you with a better result than a wrench.
As a result, if you’re wondering How to Remove Toyota Oil Filter without Wrench, all of these tools and techniques can be used.
There is yet another approach that can be advantageous for removing the oil filter without a wrench. But before attempting any of the other ways, this one should be tried.
The first method to try
Sometimes oil filters are loosely fastened, and you can even use your hand to access a Toyota oil filter. Give it a shot and attempt to open the oil filter counterclockwise. Maybe it’d be simple to open. You should use safety precautions and attempt it for this reason. To open the Toyota oil filter with your hands, keep in mind that gloves are recommended.
We should understand the importance of changing the oil filter after learning how to completely remove a Toyota oil filter without a wrench.
Importance of changing oil filter
The requirement to remove the oil filter in order to replace it is a fundamental phenomenon. In order to preserve the car’s reputation and keep the engine in good shape, it’s crucial to change the oil filter.
Facts to remember
Everyone should be aware of a few crucial details before attempting to remove the Toyota oil filter, both with and without a tool.
Verify that your car is chilly and that it was not in drive mode prior to two hours of work.
Before attempting to remove the filter, re-oil it since occasionally it won’t unscrew if there isn’t any oil on the filter.
You should also be aware of the proper technique for removing the oil filter with any instrument. It would be more tightened rather than becoming loose if you were to remove it in the wrong way.
Toyota oil filters: Are they all the same?
Keep in mind that not all oil filters conform to Toyota’s exacting requirements. A non-Toyota filter element can not function as well and even clog, costing your engine money. Always specify a Genuine Toyota oil filter to save your engine (and your wallet).