How to Change a Flat Tire Guide
- Stop and park in a secure area.
- Your hazard lights should be on.
- Apply the wheel wedges and parking brake.
- Take off the wheel cover or hubcap.
- Take off the lug nuts.
- Leverage the Jack to raise your Toyota.
- Take off the lug nuts.
- Take the flat tire off.
In This Article...
Where does the front of a Corolla jack up?
- Make sure the car is parked on a level surface.
- Turn off the automobile and apply the parking brakes (or emergency brake).
- Ideally, you should be able to lock the wheel that is diametrically opposed to the one you want to lift. You can perform this with a block, stone, or anything else you have on hand.
- Find the jacking locations below the car. They are situated just in front of the back tire and after the front.
- Correctly insert the jack into the jack point. The jacking point should be at the center of it.
- Take the following safety measures. When a tire jack is used incorrectly, the car could quickly drop off the jack and cause significant damage or even death. If you don’t have a jack stand handy, a smart solution is to utilize the spare tire under the car. Avoid placing any part of your body underneath the car while the jack is holding it up.
- Raise the car slowly. Make sure the jack stand is still in the right place and not moving when raising. Avoid raising the automobile higher than is required to install a jack stand or to freely remove a tire. If utilizing a jack stand, place it underneath the vehicle and slowly lower it until the vehicle is resting on the stand.
Warning, Do not do this when using the tire jack
- If someone is inside the car, don’t raise it.
- Never place something on or under the jack when elevating the car.
- Don’t raise the car any higher than is necessary to change the tire.
- If getting beneath the car is necessary, use a jack stand.
- Make sure nobody is anywhere near the car before lowering it. Before descending, sound a warning to any surrounding persons.
FIND A SAFE LOCATION
Do not suddenly brake or turn when you first notice you have a flat tire. Slow down and look about for a straight, flat section of road with a wide shoulder. The best location would be a parking lot that was empty. It is advantageous to have level terrain since it will keep your car from rolling. Furthermore, straight sections of road are preferable to curves since they increase the likelihood that incoming vehicles will spot you.
Never try to replace a tire near oncoming traffic on a small shoulder. Move forward (slowly) until you reach a safer location. Although driving on a flat tire puts your rim at danger of damage, this is better than getting struck by an inattentive motorist.
Make sure to examine the precise instructions for changing a flat tire for your vehicle in your owner’s manual.
TURN ON YOUR HAZARD LIGHTS
Other drivers will be able to see you on the side of the road thanks to your hazard lights or flashers. They should be turned on as soon as you recognize you need to stop in order to prevent an accident.
APPLY WHEEL WEDGES
To make sure the car doesn’t slide while you patch the flat tire, wheel wedges are placed in front of or behind the tires. Put these in front of the front tires if you’re changing a rear tire. Put the wheel wedges behind the rear tires if the front tire is flat.
Real wheel wedges are not necessary; you can just use bricks or big stones. Simply make sure they are substantial enough to prevent the automobile from rolling.
REMOVE THE HUBCAP OR WHEEL COVER
It is simpler to take off the hubcap before raising the car with the jack if your car has one covering the lug nuts. You can move on to Step 6 if your lug nuts are visible.
To remove the hubcap, use the flat end of your lug wrench. Most automobiles can use this, but some hubcaps require a specialized tool to remove. For instructions on how to remove a hubcap or wheel cover properly, go to your owners manual.
LOOSEN THE LUG NUTS
Turn the lug nuts counterclockwise with the lug wrench until they lose their resistance. It’s okay if you have to use force. If required, use your foot or your entire body weight.
The lug nuts should be loosened by 1/4 to 1/2 turn, but not yet totally removed. Save that for when you need to take your tire or wheel off the car.
PLACE THE JACK UNDER THE VEHICLE
Under the car’s frame, next to the flat tire, is normally where the jack should be placed. A cleared piece of exposed metal on the bottom of many car frames is designated for the jack and is covered in molded plastic. Use the jack in accordance with the owner’s manual’s directions to properly lift the object without causing harm to the car.
RAISE THE VEHICLE WITH THE JACK
Before attempting to elevate your vehicle, lay a little cut of 2×6 wood beneath the jack to keep it from collapsing under the weight of your car and losing equilibrium. On asphalt, this strategy is very useful.
Lift the car with the jack in the right place until the flat tire is roughly six inches off the ground.
Never place any portion of your body under the car while it is being raised with the jack or later.
REMOVE THE FLAT TIRE
Pull the tire gently in your direction while holding it by the treads until it is totally free from the hub behind it. To prevent it from rolling away, position it on its side.
TIGHTEN THE LUG NUTS BY HAND
Reinstall the lug nuts on the lug bolts and manually tighten them all the way. Once they are all attached, double-check each one and tighten as much as you can. After lowering the car to the ground, you’ll use the wrench to tighten them.
LOWER THE VEHICLE AND TIGHTEN THE LUG NUTS AGAIN
Lower the car using the jack so that the spare tire is on the ground but that the tire isn’t bearing the entire weight of the car. Now, using the wrench and rotating in a clockwise direction, tighten the lug nuts as much as possible. Use your entire body weight to press down on the lug wrench.
LOWER THE VEHICLE COMPLETELY
Remove the jack and fully lower the car to the ground. To make sure the lug nuts are as snug as possible, give them one more tug with the wrench.
REPLACE THE HUBCAP
Put the hubcap you removed from the flat tire back on if it fits your spare tire after first removing it. If it won’t fit, store it with the tire when you store your equipment if it isn’t necessary.
STOW ALL EQUIPMENT
A jack, a lug wrench, wheel wedges, your flat tire, and perhaps a hubcap are the items you have in front of you. Before you go, remember to load them all into your car.
CHECK THE PRESSURE IN THE SPARE TIRE
To make sure the spare tire is secure for driving, you should check the tire pressure. Mini-spares, commonly known as T-Type temporary spares, need 60 psi. If the tire has to be inflated, proceed (slowly) to a gas station right away.
TAKE YOUR FLAT TIRE TO A TECHNICIAN
Driving long distances or at high speeds is not recommended with temporary spare tires, so proceed with caution until you can see a tire technician. If your tire needs to be repaired or needs to be replaced, a professional should be able to tell.
What steps are involved in replacing a tire?
Tire flat and stuck? Here are the 10 steps to changing a tire.
- Locate a Secure Overpass to Pull Over.
- Inspect the materials.
- Your car should be raised off the ground.
- Remove the Tire and the Lug Nuts.
- Fix the spare tire to the vehicle.
- Switch out the lug nuts.
- Lower the car and start tightening.
What instrument do you use to remove a tire?
As you continue down the road, you feel a disturbance, hear a thump, and then a loud flapping sound. Wherever you heard the sound, your steering wheel starts to pull in that direction. Your tire just developed a flat. If you have never encountered this issue, you likely have a few questions. I need to fix a flat tire; what tools do I need? How can a flat tire be changed? We’ll be showing you how to achieve that today.
What do I need to change my tire?
Your car might occasionally have a secret compartment in the trunk that contains these supplies. If your car does not have the concealed compartment, you must get this. A spare tire, an impact wrench, a lug wrench or deep socket wrench that fits the lug nuts/bolts, and a jack are the four tools required to change a tire. Scissor jacks, bottle jacks, and bumper jacks are the three types of jacks that are available for purchase. Depending on the make, model, and year of your car, you might also require a wheel lock, extensions bars, and alignment studs.
There are several convenience gadgets you’ll want to buy even if this is all you truly need to change a tire. Professional mechanics advise having a flashlight, hand wipes, tarp or mat, plastic rain poncho, tire pressure gauge, tire blocks, road flares, or reflective triangles, and a piece of plywood on hand.
Can a tire be changed while the emergency brake is engaged?
Nobody wants to change a flat tire on the side of the road. Even at its worst, the task is disagreeable and potentially dangerous.
According to a National Highway Transportation Association research, tire blowouts cause thousands of accidents each year, many of which result in fatalities. Regular tire inspections and maintenance by a certified tire specialist are one approach to avoid blowouts and flats.
Fortunately, most flat tires don’t cause mishaps or injuries. Even minor tire adjustments, though, can wreck your day. Here are seven things you should never do when changing a flat tire in order to ensure the process is as secure and simple as possible.
According to drive-safely.net, if you can’t find a parking space or a secure spot to pull into, try to get as far away from the road as you can. It is hazardous to attempt a tire change while moving traffic is passing only a few feet away. It is preferable to have to replace a worn out vehicle than to get struck by another car after using it while flat.
Always light road flares or danger reflectors before replacing a tire. Flares signal other cars to give you more room to maneuver. Additionally, you should activate your hazard lights, as well as open any doors or the hood of your car. To ensure that other drivers can easily see you and keep a safe distance, you should be as visible as you can.
The lug nuts that secure wheels are typically tight. To free them, you frequently need to use a lot of force. The wheel will just spin if you jack up the car before you loosen them. That is impossible due to the car’s weight on the ground. The lug nuts should be removed after the nuts have become loose.
A car jack seems to be an easy tool to use, and jacking up a car sounds simple. In fact, vehicle jacks can be hazardous and annually cause tens of thousands of injuries and even fatalities. The U.S. National Highway Traffic Safety Administration estimated that car jacks result in up to 5,000 injuries annually in a 1998 study. According to information from the National Coroners Information System, 29 deaths in Australia between 2000 and 2007 were deemed to be the result of car jacks. The majority of fatalities and injuries are caused when vehicles fall off of jacks, however even with proper use, certain jacks have powerful hydraulic systems or hefty springs that can be harmful.
You don’t want to hoist the spare higher than is absolutely necessary because it is heavy. Additionally, you don’t want to reach into a jacked-up car’s trunk or hatch to retrieve the spare tire. Next to the wheel you are replacing, roll the spare tire.
After successfully changing a tire, you ought to bring your car to an established tire repair shop. You need to get the flat tire patched or changed as soon as you can because many spare tires are not designed for extended use. It pays sense to have the car inspected by a certified tire expert because flat tires can occasionally result in additional harm.
A communication master’s degree is held by Flint Stephens. He frequently writes about economic, financial, and medical issues.