From underneath the car, it is simpler to locate the starter motor. In order to gain access to what you need, lift the car and use two jack stands.
- Utilize wheel chocks and set the parking brake, please.
- Before starting work, disconnect the battery’s negative terminal.
You can use the images of the original and substitute starter motors below as a guide.
To identify the starter and reach the top bolt to replace it, the air cleaner housing must be taken off from the top of the engine compartment.
To remove the starter, two bolts are required. As follows:
An electrical connection has two terminals: a positive terminal and a negative terminal. A clip secures the single contact connector used for the negative connection. Bolt, nut, and lock washer make up the positive terminal.
Since the plastic skirting is sufficiently flexible, we were able to remove the old starter and install the new one via the wheel well on the passenger side.
In This Article...
How much does a Toyota Corolla starter replacement cost?
Estimated price for replacing a Toyota Corolla starter. Replacement starters for Toyota Corollas typically cost between $273 and $434. While parts are priced between $212 and $358, labor is predicted to cost between $61 and 77.
How can I tell if my starter is defective?
Still, keep an eye out for these seven indications that your starter is failing.
- #1: The Engine Won’t Start.
- #2: Loud, grinding, or whirring noise.
- #3: Occasional Trouble Starting the Car.
- #4: The Starter Continues After the Start.
- #5: Smoke.
- #6: The starter engages but the engine won’t turn over.
- 7. Battery
For a 1997 Toyota Corolla, what is the cost of a starter?
For your 1997 Toyota Corolla, we now offer 6 Starter items, with prices ranging from $99.99 to $189.99 in our inventory.
Can I change a starter on my own?
The majority of people believe that if their automobile won’t start, the battery is to blame. They attempt to boost it, but it still won’t turn on. Obviously, it’s a beginner or something little more severe. The alternator receives a charge from the battery of the car through the starter. The alternator’s charge makes it possible for the car to start. The car is dead if the starter is worn out since it won’t accept or send a charge. A repaired starter is just as effective as a new one and is less expensive than buying a new one, which is pretty pricey [source: Allen]. Save money by replacing the starter yourself if it is the true source of the issue. How to change an automobile starter is as follows:
- In order to disconnect the negative battery cable from the battery, turn off the ignition.
- From the starter, unplug the positive cablethe substantial cable that connects to the battery.
- Using a ratchet, unplug each of the bolts holding the starter to the block.
- Any additional mounting brackets keeping the starter in place should be removed.
- The starter’s bolts must all be removed. Bolts that are difficult to remove or extremely tight should not be forced. Instead, use oil or lubricant to aid in removing the bolt.
- Take the starter out of the vehicle.
- The new starter should be mounted on the block and fastened with bolts. Reconnect the battery cable to the starter before tightening the bolts.
How long does a starting replacement take?
Depending on where the starter is located in your engine, replacing one will take anywhere from two to four hours.
Some engines have starters that are easier to access than others. To get that starter, a mechanic might need to scrounge around and remove certain components. If so, a 4 hour time limit would likely be more appropriate than a 2 hour one.
Download the Jerry app to see if you’re overpaying for auto insurance as you wait for the technician to finish. We warrant that replacing your starter will be much quicker!
Simply spend a minute to respond to a few questions, and Jerry will do the rest of the work for you. To find you the greatest bargain, they’ll create competitive quotations from top insurance companies. When a customer shops with Jerry, they often save over $800!
How much does an Autozone starter cost?
Starting at $50 up to $350, rebuilding parts for a starter can be expensive. A new starter might cost anything between $80 and $350. You should budget between $150 to more than $1,100 for a trained mechanic to replace or rebuild your starter.
On a 1996 Toyota Tercel, where is the starter?
The starter is situated on the drivers side of the engine, next to the firewall. Use Google for images, perhaps. Now, IF you choose to attempt this: > FIRST THING, DISCONNECT THE BATTERY NEGATIVE TERMINAL CABLE. Take care! Have success with that. Simply put, I’m telling it as it should be said.
Can a car with a bad starter be jump-started?
Although a car with a defective starter can be jump started, the underlying problem will not be resolved. Your car’s battery is what gets boosted by a jump start, not the starter.
While a jump start can help the starter acquire the extra power it needs to start your engine because the starter is powered by the battery through a relay, it is not certain that a jump start will be helpful if the problem is with the starter.
For a proper diagnosis and solution to the problem, you are best off visiting a mechanic. Jumping your car every morning is not a workable approach, regardless of the circumstance!
A reliable strategy to make sure you’re taking good care of your set of wheels is to take it to the mechanic, along with giving it a robust vehicle insurance coverage.
In less than a minute, Jerry will produce comparable quotes from leading providers if you’re looking for auto insurance.
How may an automobile starter be tested without removing it?
Q My 1999 Toyota Tacoma’s rebuilt starter has just been installed; the previous one had shorted out and refused to disengage. The new one, though, won’t interact. When the key is turned, all that can be heard is a quiet click. Any thoughts?
A Did you test the old starter to be sure it was defective? The starter may continue to engage if a relay or solenoid is shorted. Check all electrical connections between the battery, relay, solenoid, and starter, assuming the replacement starter motor is in working order. Take a close look at the starting relay’s socket. And ensure that the engine/drivetrain and the chassis have a strong ground connection.
Using jumper cables to disengage the car’s electrical system is the simplest approach to examine the starter. With the engine off and the transmission in “park,” carefully attach one end of the red/positive jumper cable to the battery’s positive terminal. Connect the red cable’s opposite end to the starting motor’s positive connector. The engine must be spun or cranked by the starter. If it does, the wires, connectors, or relay are the cause of the issue. If not, start the engine and use the black/negative jumper cable to establish a connection between the drivetrain and the battery’s negative terminal as a ground. Connect the red cable to the positive terminal of the starter. If the starter turns the engine over, a poor chassis ground is the issue.
Once more, use extreme caution when performing these tests to keep yourself safe. Remove the new starter, or even better, test it on your workbench.
Q I am rebuilding a 1988 Nissan Pathfinder V6 with 149,000 miles. One issue that I’d really like to fix is the fact that the engine always behaves as though the temperature is 30 below zero! The engine may be running at 2,000 to 2,400 rpm while the outside temperature is 90 degrees. Only the first start of the day results in this.
A A “fast idle control device” (FICD) and an idle-up solenoid are used by this early fuel injection system to regulate fast idle during startup. The crank angle sensor, coolant temperature sensor, ignition, and battery provide data to the FICD. Although the first idle speed of 2,000 to 2,400 rpm is correct, normal idle should arrive sooner. The two gadgets mounted on the throttle body would be checked.
Q My 1999 Chrysler Sebring has about 112,000 miles on it. My car won’t run correctly when the temperature is below zero. When I let up on the throttle or go into gear, it will start rough and die. Once fully warmed up, it functions normally. The gasoline pump may be the issue, but the dealer wasn’t sure, and fixing it would cost $900. What shall I do?
A Although low fuel pressure may be a contributing factor, the symptoms don’t really match a fuel-pump issue. Check the fuel pressure with a shop, then connect a scan tool to check for trouble codes. Have the shop verify the accuracy of the coolant temperature sensor signal with the engine completely cold. The idle air control actuator can be tested or reset using the scan tool.
Are basic maintenance items like air and fuel filters, spark plugs, and the like current on the vehicle as well? The car is approaching its operational limits when the temperature falls below zero, therefore regular maintenance can make the difference between the vehicle starting and not starting.
A damaged starter will it still start?
Engine Isn’t Starting or Cranking An engine that won’t crank or start is the most evident indication of a bad starter. Of course, a broken starter isn’t the only problem that can stop the engine from starting. A few instances are a dead battery, a broken ignition switch, or a mechanical issue with the engine.