Jump-starting a Prius or another Toyota hybrid is quite similar to jump-starting a gas-powered car. Jumper cables, a helping vehicle, and a solid metallic point are all required to jump a Prius.
In This Article...
Can you jump a 12 volt Prius?
Do not worry! A Prius or any other Toyota hybrid may easily be jump started, and the staff at the Brent Brown Toyota service center is ready to assist. All you need are jumper cables, a car with a strong battery, and a solid metallic point, just like jump-starting a gas-powered automobile.
What occurs if the battery in a Prius dies?
When a hybrid vehicle’s battery begins to fail, the vehicle’s fuel efficiency may suffer or its ability to hold a charge may be compromised. The automobile won’t start when the battery is entirely dead.
Can you recharge a dead Prius battery?
- The hybrid battery will be in the fuse box, which may be found by lifting the hood.
- Attach the red jumper cable to the battery’s positive (+) terminal. Connect the same cable to the positive terminal (+) of a second car by running it there.
- Connect one end of the black jumper cable to the unpainted metal component on the dead automobile, and the other end to the negative (-) terminal on the battery of the functional vehicle.
- Start the second car’s engine, and then let it run for a while.
- Start the Prius and watch for the Ready notification to appear on the dash.
- Once the connections are disconnected, you should be set to go.
However, if you drive the car for roughly 20 minutes, the hybrid battery should recharge on its own. Therefore, if your battery is continually depleting to the point that your Prius won’t start, it’s usually a symptom of bigger problems or that the battery needs to be replaced entirely.
A Prius battery replacement is not inexpensive. Parts and labor should cost between $2,500 and $4,500. When this occurs, many Prius owners even consider purchasing a new car.
Make room in your budget for new batteries or a new car by using the Jerry app to save money on other auto expenses like your insurance.
Jerry is a certified insurance broker who can quickly get quotations from more than 50 highly regarded insurers. Jerry can assist you with purchasing new insurance and canceling your old policy if you discover a fantastic deal. Every year, users save $887 on average.
Can I leapfrog a Prius from a trunk?
Like any other vehicle, a Prius may be jump started, but there are a few things you should be aware of. First, rather of being under the hood, the 12V battery is in the trunk. If you could open the trunk while the battery is dead, this wouldn’t be a big problem, but you can’t. The latch is released by the trunk using a switch and an actuator. It won’t operate and you won’t be able to open the hatch without batteries. Additionally, the smart key won’t function. It also requires 12V electricity. This brief guide will describe how to get past these challenges and kickstart your Prius.
With a dead battery, how do you start a hybrid vehicle?
- Avoid overusing your hybrid vehicle’s jumper cables on other vehicles as this can harm the electrical system.
- Turn off your headlights and inside lights, then engage your parking brake.
- Disconnect the hybrid system and take your key off.
- Fuse block cover, hood, and special jump-starting terminal cover should all be opened.
- The exclusive jump-starting terminal should receive the positive clamp (red) jumper cable.
- Connect the vehicle’s discharged battery’s negative clamp (black) to a stable, solid, unpainted metallic point.
- Make sure all unneeded lights are turned off and that the vehicles are not touching if the booster battery is put in another vehicle.
- When boosting a car, always utilize a battery that is the same or better in quality.
- Allow the jumper cables to be attached and the discharged battery to rest for five minutes. Then, with the gas pedal barely depressed, run the engine of the car that is boosting at roughly 2,000 RPM.
- Make sure the “ready light is on” before starting the hybrid system.
- After the negative cable, disconnect the positive cable.
The Prius’s 12 volt battery is located where?
You must determine whether you want to keep the vehicle’s electricity on at all times before beginning the work. Even while it won’t be a big deal, if you don’t retain power, you’ll lose things like radio presets and power window limits. Both errors can be easily fixed by entering the radio information once more and repeatedly raising and lowering the windows.
You’ll need jumper cables or a battery charger, a second battery (perhaps in another car), if you wish to prevent this minor issue. Once the power supply is connected, follow the instructions in the section below. Please pay attention to the warning there.
- Open the hatchback and take out any floor mats you may have there. Get rid of the carpet and the covering on the secret storage area.
- The spare tire may be seen by removing the plastic storage container.
- In the back of the trunk, under a piece of plastic molding, is where you’ll find the battery. Molding should be released and taken out. The battery will be made visible in this way.
- A square air duct used to cool the primary driving battery crosses the top of the battery. It must be taken out before the battery can be removed since it is far too close to the battery to allow removal. Behind the side carpeting on the automobile, there is a 10 mm bolt, and there is another one closer to the middle. The duct can then be worked out and put aside after raising the carpeting high enough to reach the bolt and remove it along with the second bolt.
- Moving the brake controller, which is located directly inside the vehicle next to the battery, will make the task much simpler. It is fastened with three 12 mm bolts; take out the bolts, then carefully move the object away. Take care not to pull too hard on the wires that are still linked to it.
- Remove the plastic casing covering the terminal as well as the positive cable from the battery. Open the terminal slightly by loosening the 10 mm bolt and using a screwdriver or tiny pry bar. Lift the terminal straight up, taking great care not to let it touch any of the car’s components. To stop it from shorting to the car body and to put it out of the way, cover it with an old glove or wrap a cloth around it.
- The bar that runs over the top of the battery is the battery hold down. Remove the hold down by unscrewing the 10 mm bolt and 10 mm nut that are located on either side of it.
- The negative terminal can be removed from the car’s body rather than the battery, which will be simpler. It is secured to the automobile by a 10 mm bolt, which is much simpler to access than the bolt on the terminal itself. Fold the wire over the battery after removing that bolt.
- On the battery’s forward side, there is a vent tube. Without removing it from the vehicle, remove the tube from the battery and set it aside.
- Remove the negative battery terminal and wire from the battery by lifting it out of the automobile. Before removing it, pay attention to how it is directed.
Jumper cables should be connected where?
One of the cutting-edge and essential services that Urgently has found to help our partners’ EV strategies and improve the ownership experience for their consumers is mobile EV charging.
Your vehicle’s battery is a crucial component that performs one of the most crucial functions: starting the vehicle. The battery in the majority of conventional vehicle types, or gasoline-powered cars, is a SLI, or a starting, lighting, and ignition battery. Its primary function is to start the engine, although it can also be used to run the car’s lights and radio. The alternator in your car produces the majority of the energy required to power it once the engine is going. However, starting the car is a crucial function of the car battery; without it, the vehicle is essentially useless. A dead battery is likely to be the cause when you turn the key and hear some spitting, or perhaps nothing at all, but the engine won’t start.
Take some time to compile some information before attempting to jump start your car. Read the manual for your automobile, paying close attention to any sections on jump starters or car batteries. Some automakers may advise you against jumping starting the vehicle, while others may provide you with unique instructions tailored to your model. Ensure that you are aware of where your car’s battery is. The engine is often located in the front of the car, under the hood. However, the battery can be found in the trunk of some vehicles. If this is the situation, there are frequently specific terminals under the hood that can be used in the event of a jump start. Look at the battery to determine which terminals are positive and which are negative. A + (plus) sign for positive and a – (minus) sign for negative markings should be plainly visible on each terminal. Knowing which is which is essential since the batteries must be connected correctly for a successful jump start and to prevent a risky mishap.
One red and one black wire should be included in a set of jumper cables. Where to attach the cables is clearly shown by the colors. In any electrical system, electrical energy travels down a wire network from a battery’s negative terminal to its positive terminal, powering an object along the way, in this case the vehicle’s starter. One needs to make sure that the proper terminals are connected in order for a jump start to function properly. The side that should be connected to the positive terminal will always be represented by the red wire, and the side that should be connected to the negative terminal by the black cable. Don’t contact anything other than the intended target with the jumper cable clamps.
Using a portable jump starter or the assistance of another vehicle, you can jump start an automobile.
In either scenario, make sure all tools and vehicles are off before continuing. Remove all of your keys from the ignition for your own safety. Make sure there are no combustible materials nearby. Sparks, fires, and even explosions are conceivable while jump starting an automobile, albeit they are rare. High volts of electricity are present in car batteries and jump starter packs, and while jump starts and cables are made to minimize the risk of wrong use, accidents can still occur in certain situations.
If you need to jump start your car using the jumper wires from another vehicle, follow these instructions:
Find the location of each car’s battery first. The battery is usually located alongside the engine in cars. Then, position the vehicles near enough to one another so that you may attach jumper cables to the batteries of both vehicles. But watch out that nothing on either automobile touches anything else. This is necessary to stop any electrical current from traveling between the vehicles other than via the jumper wires. To start the process, both automobiles need to be put in park and turned off. Again, take note of the positive and negative terminals on each battery. After that, connect the jumper cables where necessary. The positive (red) cable needs to be connected to each battery’s positive terminals. The negative (black) cable needs to have one end grounded and the other end connected to the dead battery’s negative terminal.
The following is the safest way to attach the jumper cables:
- One red jumper cable clamp should be attached to the dead battery’s positive terminal.
- The positive terminal of the functioning (live) automobile battery should be connected to the opposite end of the same wire, the second red jumper cable clip.
- One black jumper cable clamp should be attached to the negative terminal of the active (functioning) car’s battery.
- On the vehicle with the dead battery, fasten the other end of that wirethe second black jumper cable clampto an unpainted piece of stationary metal. Don’t connect this clamp to the dead automobile battery’s negative terminal.
Though some might argue that it’s acceptable to secure the last negative jumper wire clamp to the dead battery’s negative terminal, doing so raises the possibility of a fire or explosion if the jump start doesn’t go as intended. To reduce the risk of sparks igniting any hydrogen gas that might be flowing from the battery, try to locate a location far from the battery. Better alternatives include the vehicle’s frame, an engine bolt, the bracket holding the alternator, or a specific grounding terminal that is not connected to the battery.
Start the vehicle with the live battery next. The dead battery will begin to recharge right away. The car with the dead battery may occasionally be able to be started right away, but other times it will require some time to charge. To allow electrical current to move from the functioning battery to the dead one, let the engine run for a few minutes. After that, try using the dead battery to start the vehicle. Start by turning the key and holding it there for no more than a few seconds. You might want to give this a few tries. If you were successful with your jump start, the engine should start right up. Depending on what caused your dead battery, you might want to get the automobile checked out right away. In other cases, your automobile can be fine following the jump start. A short drive will assist in recharging the battery.
The jumper cables must be cut off as the final step. It should be done in the opposite sequence from how they were connected. You run the risk of transmitting an electrical charge somewhere you may not want it if you touch the cords before they are entirely removed.
So, it’s advisable to do these steps in the following order:
- On the vehicle that was given a jump start, disconnect the negative (black) jumper cable clamp from the chassis or terminal.
- Negative (black) jumper cable clamp should be disconnected from the functional battery’s negative terminal.
- Remove the positive (red) jumper cable clamp from the positive terminal of the working battery.
- From the vehicle that received the jump start, disconnect the positive (red) jumper cable clamp.
Congratulationsyou just jump-started your car! Don’t forget to express your gratitude to the neighbor, friend, family member, or good samaritan that lent you their live battery to assist you out!
However, if your jump start doesn’t work and you find yourself repeatedly twisting the key in the ignition without the engine starting, you might be dealing with a bigger issue. In this situation, it is best to either have a mechanic inspect the vehicle or tow it to a repair facility.
If you’re using a portable jump starter to jump start your car, follow these instructions:
Portable battery packs, jump starters, and jump boxes are frequently small enough to be kept in your car’s glove box or trunk in case you need them. However, make sure to read the instructions carefully because not all of them can be stored in the hot, high temperatures that summertime cars can reach. The jump starter should be off when you start the process, just like when you jump start another automobile. You should also turn off your vehicle’s accessories.
Many portable chargers and jump starters have two clamps that are permanently attached to the device. One positive (red) and one negative (black) clamp should be present. To help prevent the likelihood of a spark, keep them apart. If the cables aren’t already attached, you’ll attach them to the portable jump starter while the car and jump starter are still off, making sure the positive (red) wire is linked to the positive terminal and the negative (black) cable is connected to the negative terminal.
Connect the clamp on the black jumper wire to either an unpainted metal item in the engine or straight to your car’s chassis, and the clamp on the red jumper cable to the positive terminal on your car battery (the frame of the vehicle). Don’t connect the negative (black) clamp to the dead battery’s negative terminal. In order to decrease the chance of sparking, which could start a fire or explosion, it is crucial to connect the cables in the correct order. It is also safer to connect the negative (black) clamp as far away from the battery as you can.
Turn on the jump starter once the cables are securely fastened. After then, try to start the car. Start the car by turning the key in the ignition and, if required, holding it there for a few seconds. Give the battery pack some time to cool down and readjust itself if a few seconds of trying to start the car doesn’t work. Your battery will receive more energy in an effort to start the car as a result of this.
If the jump start was effective, you should hear your engine start to turn over and run independently. Congratulations! The cords for the jump starter can now be unplugged. Remove the positive (red) cable from the battery terminal after removing the negative (black) cable from the vehicle. Depending on what caused your dead battery, you might want to get the automobile checked out right away. In other cases, your automobile can be fine following the jump start. A short drive will assist in recharging the battery.