A switch located beneath the steering wheel, on the right side, can be used to activate the 2019 Highlanders tire pressure display. TPMS should be displayed on it, which is located inside the instrument panel. Hold down this button until you see the TPMS indicator on the panel flash three times on and off. Wait a few minutes after these blinks have finished before starting the car. The vehicle should have ample time to record and show the tire pressure after this. Simply follow the same procedures and take the car for a brief drive to reset the TPMS monitor. You should be able to reset Your tire pressure indicator after about fifteen to twenty minutes.
In This Article...
Does the Toyota Highlander have a system for monitoring tire pressure?
The tire pressure monitoring system warning light will illuminate if your TPMS sensor has stopped working or its battery has run out. Count on the professionals at your local Toyota service center to complete the required repairs on your Toyota Highlander in a professional manner.
How can I check my Toyota Highlander’s tires for pressure?
On the instrument panel, it is located low and to the right of the steering wheel. Hold down the button until the instrument panel’s TPMS indicator light blinks slowly three times. Turn off the engine after letting it run for a few minutes so the system has time to record the pressure of each tire.
The 2015 Toyota Highlander displays the tire pressure, right?
The Toyota Highlander and Highlander HV’s tire pressure monitoring system (TPMS) was created to alert the driver when one or more of the vehicle’s road tires had low tire inflation pressure.
Each tire and wheel assembly has a tire pressure warning valve sub-assembly attached with a tire pressure sensor/transmitter. The tire’s internal temperature and air pressure are both measured by the sensor. Radio waves are used to convey these measured values as well as the transmitter ID to the tire pressure monitor antenna and receiver assembly on the body.
The tire pressure monitor receiver then transmits this information to the tire pressure monitor ECU.
The ECU compares the measured air pressure value and the standard value if the transmitter ID has already been registered.
The tire pressure warning light in the instrument cluster will illuminate if the value is lower than the baseline value stored in the tire pressure monitor ECU.
A tire pressure warning reset switch is used to re-set the warning threshold in response to variations in tire pressure values brought on by changes in tire type and installation position. Following specific repair operations, the system is initialized using this switch.
The following circumstances may prevent the system from operating properly:
- Near the car are structures or gadgets that operate on related radio frequencies.
- In the car, a radio with a comparable frequency is utilized.
- On the glass, there is a coating or window tint that could interfere with radio frequencies.
- The car is heavily covered with snow or ice, especially on the wheels and in the wheel wells.
- Use of wheels that are not the originals could cause a system failure or air leak.
- Chains for tires are utilized.
- Tire chains or snow tires are employed.
- if the placement of the spare tire is not good for receiving radio waves.
- if you store something bulky and metallic in the trunk that can obstruct your ability to receive signals.
- Because the full-size spare tire is fixed, a signal might not be received when it is outside the electric wave’s range of reception. As a result, the system might not work properly. Rotate the full-size spare tire 90 to 270 degrees if there’s a chance the tire pressure warning system won’t get a signal from it.
- if the system was started up with tires that weren’t inflated to the recommended levels.
NOTE: Natural events like tire pressure variations brought on by temperature or air leaks in the tires may cause the tire pressure warning light to come on. The warning light in this instance will be extinguished by changing the tire pressure.
NOTE: Adjust tire pressure to a higher pressure appropriate for cold situations if the warning light appeared due to extremely low outside temperatures that result in tire pressure drops (such as in the winter). Every 18 degrees Fahrenheit (10 degrees Celsius) decline in the outside temperature results in a 1.45 psi (10 kPa) drop in tire pressure.
NOTE: The tire pressure warning valve and transmitter are not included with the small spare tire. When the flat tire is swapped out for the spare, the warning light will not go out. The warning light will turn off once the regular tire is fixed, inflated to the right pressure, and put back on the car.
Check tire pressure if the tire pressure warning light does not turn off or comes on while you are driving. After correcting the tire pressure, if the tire pressure warning light still illuminates, there may be a slow air leak in the tire.
The tire may be punctured if the warning light is still on even when the tire pressure is set correctly. Whenever necessary, fix.
The tire may have a slow air leak if the warning light comes on soon after adjusting the tire pressure. Whenever necessary, fix. After looking into all of the aforementioned scenarios, if the warning light is still on or blinking, there is a TPMS issue. Consult the relevant manufacturer service documentation.
When tires are replaced with tires of a different pressure or when the tire pressure sensor and/or tire pressure monitor ECU are replaced, the system must be reset. Refer to “Setting up the tire pressure monitoring system.” Prior to system initialization, the tire pressure monitor ECU must memorize the sensor ID when a tire pressure sensor and/or tire pressure monitor ECU are replaced. See “Registration of tire pressure sensors.
Check tire pressure if the tire pressure warning light does not turn off or comes on while you are driving. Set the recommended tire pressure. Verify that the warning light disappears after a short while.
NOTE: Initialize the window control system, back door system, sliding door system, and moon roof power systems after the negative battery terminal has been reconnected if it has been unplugged. Consult the owner’s manual or the pertinent manufacturer service manual.
Before initializing, make sure that the tire pressure is within the recommended range. DO NOT click the reset button until all tires have been properly inflated (including the spare tire). Otherwise, even if the tire pressure is low, the low tire pressure warning light might not turn on, or it might turn on even though the tire inflation pressure is truly normal. Initialization is not carried out if the reset switch is pressed while the car is moving.
NOTE: If the tire pressure sensor, tire pressure monitor ECU, or both are replaced, the system will need to be reset when the tires are replaced with tires of a different pressure. Before starting, adjust tire pressure to fall within the prescribed range. Prior to system initialization, the tire pressure monitor ECU must memorize (register) the sensor ID when a tire pressure sensor and/or tire pressure monitor ECU are replaced. See “Registration of tire pressure sensors.
NOTE: After the tires have fully cooled down, adjust the tire pressure.
NOTE: The initialization typically takes two to three minutes to complete. After roughly 20 minutes, the DTC C2177/77 will be set if the initialization was unsuccessful. Connecting the DLC3’s terminals 13 (TC) and 4 (CG) will stop initialization.
The tire pressure sensor checks the tires’ inflation pressure during initialization and records the signals that are sent once every minute into the tire pressure monitor ECU. Once the signals from the tires (including the spare tire) have been received, the initialization process is finished. If the ignition switch is changed to the OFF position before initialization is finished, the initialization procedure is aborted. The tire pressure warning reset switch needs to be pressed once more to resume startup.
1) As stated on the tire and loading information label, set the tires to the prescribed (cold) pressures.
2) Switch the ignition on.
3) When the tire pressure warning light blinks three times, press and hold the tire pressure warning reset switch for at least three seconds (one second on, one second off). Look at Figures 1 or 2.
Does Toyota alert you to a low tire?
The TPMS in your Toyota will identify extremely low tire pressure on at least one of your tires if this warning light stays on while you’re driving. Numerous factors, including risk-free ones like rotating tires, changing tire sizes, and altering tire pressure, can cause this warning to appear.
Do 2007 Toyota Highlanders come equipped with TPMS sensors?
All American-made automobiles must have direct or indirect TPMS systems fitted as of 2008 as a result of the TREAD Act’s 2007 mandate.
The Toyota Highlander has a direct TPMS system fitted, which means the wheel has TPMS sensors. In the event that one or more tires on a Direct TPMS vehicle show low tire pressure, the TPMS sensors will communicate this information to the car’s ECU. Each tire pressure or an indicator light (low-line TPMS system) will be displayed on the dashboard (high-line TPMS system).
After a sensor change or tire rotation, a TPMS relearn is advised. A TPMS relearn is necessary to transmit sensor data to the vehicle’s ECU when services, such as tire changes or TPMS sensor replacements, are carried out on one or more tires of a Toyota Highlander.
How are tire pressures checked?
determining tire pressure
- Remove the cap covering the tire’s air valve, and store it safely away.
- For a few seconds, firmly press the tire gauge against the exposed valve stem.
- Check the air pressure display.
- Compare this value to the tire pressure that is advised.
- Change the air valve cap on the tire.
Where is the Toyota Highlander’s button to reset tire pressure?
The TPMS, or tire pressure monitoring system, in your 2017 Toyota Highlander occasionally needs to be reset before getting an accurate reading after reinflating your tires or having new ones put. Fortunately, it’s simple and takes only a few minutes to reset the tire pressure sensor.
Your Toyota Highlander’s tire pressure sensor needs to be reset in order to turn off the TPMS light.
- Make sure the tires are filled appropriately.
- Don’t start the engine after turning the ignition switch to the On position. Push the Power button twice without depressing the brake if your automobile is a push-starter.
- Find the TPMS Set button, which is usually located beneath the steering wheel.
- Keep holding down the Set button.
- Once the warning light has flashed three times, let go of the Set button.
- Before switching the ignition switch to Off, wait a while.
By comparing quotes from different lenders, you should routinely check to determine if you’re paying too much for auto insurance, just like you should do with your tire pressure.
Use Jerry if you’d rather to let someone else handle the laborious task of collecting quotes. The Jerry app can instantly and for no cost gather quotes from more than 50 of the best insurance providers, including Travelers, Nationwide, and Progressive. Agents are available by text message if you ever have any questions, and they even help you cancel your previous policy once you’ve made your decision.
Why, Toyota, does my tire pressure light remain on even after filling the tires?
Try the following if your TPMS light is still on after you have inflated your tires to the recommended pressure: 10 minutes at a speed of 50 mph would be plenty. When you start the car again, the TPMS light ought to be off because this ought to reset the tire sensors.
Toyota does it display tire pressure?
Your vehicle’s tire pressure monitoring system, sometimes referred to as the Toyota Tire Pressure Light, is one of the most crucial components in your Toyota sedan, SUV, truck, or van.
How can I determine my Toyota’s tire pressure?
The low tire pressure icon will appear in the instrument display and a warning message will appear in the Multi-Information Display if the Tire Pressure Monitor System detects critically low pressure in one of your tires.
If the warning light continues to flash, check all the tires and top off, fix, or replace any that have inadequate air pressure.
The warning could be activated by rotating tires, adjusting tire pressure, or changing tire sizes.
After starting the car, hold down the reset button while doing so. On the instrument panel, it is located low and to the right of the steering wheel.
Hold down the button until the instrument panel’s TPMS indicator light blinks slowly three times.
Turn off the engine after letting it run for a few minutes so the system has time to record the pressure of each tire.
When you start the car, if the light turns on and blinks, it can mean that something isn’t functioning correctly. You should take it to Passport Toyota to be checked out.
You must have a Toyota dealership register any wheels or pressure sensors you replace with aftermarket parts.
Disclaimer: When tire pressure is dangerously low, the Toyota Tire Pressure Monitor warns the driver. Tire pressure should be periodically monitored using a gauge; do not rely only on the monitor system for the best tire wear and performance. For details, refer to your owner’s manual.
Not all vehicles and model grades come with every feature. Please refer to your Owner’s Manual for more information, including crucial safety data.
Are there tire pressure sensors in Toyota vehicles?
Tire Pressure Monitoring Systems are standard on all new Toyota vehicles (TPMS). Essentially, the system’s function is to inform drivers when a tire or tires are in need of being refilled, repaired, or replaced. Any queries customers may have about the TPMS in their Toyota car can be addressed by the service team here at Toyota Palo Alto. Come see how the Tire Pressure Monitoring System in Your Toyota Vehicle operates with our team today!
What Should You Do When the Tire Pressure Monitoring System Warning Light is Active?
In order to measure the tire pressure for each of the car’s four tires, the Tire Pressure Monitoring System in your Toyota vehicle essentially uses sensors. The TPMS Warning Light and a warning message will both illuminate on your Toyota instrument panel when one or more of your tires have too little air in them. Now, drivers should check the pressure in each of their four tires, and if required, fill them. If, after doing so, the warning light and message still appear, you should contact your neighborhood mechanic or a Toyota dealership to have the problem further investigated.
How Do You Reset the Tire Pressure Monitoring System?
Sometimes the warning will also appear after you rotate your tires, change your tire size, or adjust the tire pressure. In these situations, all you have to do is reset the TPMS to account for the modifications you made to your car’s tires. Simply press and hold the while the engine is running to reset the TPMS “Most Toyota models include a reset button on the instrument panel to the right of the steering wheel. Keep the “Press the reset button three times until the TPMS Warning Light blinks slowly. To finish the reset procedure, let the engine run for a few more minutes and then shut it off again.
Visit us at Toyota Palo Alto right away if this procedure doesn’t work if you think your Toyota vehicle’s TPMS is seriously malfunctioning. Visit us as well to learn more about the service specials we have to offer!