Disclaimer: The recommendations in this account are generic in nature and should not be construed as instructions for your particular car. To make repairs, please refer to your owner’s manual or repair manual.
Although it’s advised to hire an expert, you can set up an aftermarket blind spot monitor on your own. Make sure you have a few tools close by and take the following actions:
- Place the measuring tape parallel to the wheels of your car. Place the calibration cloth behind the car after removing it from your system. Make sure it is 90 degrees apart from the measuring tape.
- Pick up a level, and lean it up against the car. It must also line up with the calibration cloth. On the car’s back bumper, make a straight line with a marker.
- Take off the back bumper. The taillights may also need to be removed.
- The calibrating places in the inner rear bumper should be cleaned with a cleaning cloth and rubbing alcohol.
- Place one of the two system-supplied magnets on the outside of the car along the lines you highlighted. Put one inside the other so they are drawn to one another. Don’t be scared to experiment with the sensor positioning. They have to be angled away from the bumper of your car at about a 20-degree angle.
- Mark the location where the magnet lies within the bumper with the marker.
- The sensors should be covered in glue before being attached to the interior of the bumper.
- Install the LED indicators inside the interior of your car. These ought to be put in a location where you can see them without taking your eyes from the road. For certain kits, placement suggestions for the indicators are included.
- Volume can be changed. Make sure the system is working properly by testing the volume. When it activates, you don’t want to be taken by surprise.
Contact a service center to have a professional handle the installation of your aftermarket blind spot monitor system if you have any inquiries or problems. A specialist can be required to take control because some systems have numerous processes and can be challenging to attempt.
In This Article...
How much does it cost to upgrade a car to have blind spot monitoring?
A reliable system should cost between $300 and $500. You might wish to install it yourself if you have a free Saturday. It is, however, a pretty drawn-out procedure. It will cost at least $200 to have a kit properly fitted.
Can a Camry have blind spot monitoring added to it?
The 2019 Camry XSE V6 model includes the Blind Spot Monitor (BSM) with Rear Cross-Traffic Alert (RCTA) as standard equipment, while the Camry LE model offers it as an optional package. There is a Blind Spot Monitor System that is even more sophisticated.
How valuable is blind spot monitoring?
One of the best safety tools is blind-spot monitoring. The likelihood of merging into another vehicle might be reduced if you pay attention to the aural or visual warnings.
Can the RAV4 Le receive blind spot monitoring?
All Standard RAV4s and RAV4 Primes come with BSMs. However, you will need to add the BSM as part of an options package on the XLE or XSE trims if you want a hybrid RAV4. The RAV4 LE Hybrid does not have BSMs.
Toyota added blind-spot monitoring when?
One of the key factors in Toyota continually ranking among the top safety rankings from the Insurance Institute for Highway Safety is the Blind Spot Monitor (BSM), which has been available on some models since 2014.
Blind spot mirrors: Are they worth it?
A blind spot mirror is a practical device attached to a car’s side mirrors to indicate the driver areas of the road that are obscured from their field of view. You can essentially maintain track of the car that is behind you and change lanes without risking your safety.
Can you upgrade an ancient car with safety features?
Health. If you drive an older vehicle without an integrated sophisticated driver-assistance system, you might want to think about upgrading it with one. These systems, which are included in many modern cars, provide safety features that warn drivers of potential dangers and assist them in avoiding incidents. An aftermarket item made by Mobileye (an Intel business), which comprises of a camera mounted on the windshield and a display mounted on the dashboard, is sold. The technology will flash or beep at you if you follow another car too closely or veer off your lane without indicating, for instance. Additionally, it will alert you if you are speeding or if there is a chance of an accident with a pedestrian or bike. However, unlike many built-in systems, it does not interfere with driving functions like using the brakes or turning the steering wheel. Over a 12-week period, testing by the Insurance Institute for Highway Safety on 22 employees using Mobileye in urban, rural, and suburban regions revealed that it led to appreciable improvements in safe driving behaviors, including utilizing turn signals more and tailgating less. Without installation, installing Mobileye in your car would set you back between $650 and $850.
Can features be added to a used car?
Unfortunately, a lot of contemporary safety features are factory-installed in the automobile, so you can’t add them without spending a lot of money that would probably exceed the price of the car.