Many Toyota models also come with Rear Cross-Traffic Alert and Blind Spot Monitor (BSM) in addition to safety features like Star Safety System and Toyota Safety Sense1 (RCTA).
In This Article...
Can blind spot monitoring be added after the fact?
Disclaimer: The recommendations in this account are generic in nature and should not be construed as instructions for your particular car. To make repairs, please refer to your owner’s manual or repair manual.
Although it’s advised to hire an expert, you can set up an aftermarket blind spot monitor on your own. Make sure you have a few tools close by and take the following actions:
- Place the measuring tape parallel to the wheels of your car. Place the calibration cloth behind the car after removing it from your system. Make sure it is 90 degrees apart from the measuring tape.
- Pick up a level, and lean it up against the car. It must also line up with the calibration cloth. On the car’s back bumper, make a straight line with a marker.
- Take off the back bumper. The taillights may also need to be removed.
- The calibrating places in the inner rear bumper should be cleaned with a cleaning cloth and rubbing alcohol.
- Place one of the two system-supplied magnets on the outside of the car along the lines you highlighted. Put one inside the other so they are drawn to one another. Don’t be scared to experiment with the sensor positioning. They have to be angled away from the bumper of your car at about a 20-degree angle.
- Mark the location where the magnet lies within the bumper with the marker.
- The sensors should be covered in glue before being attached to the interior of the bumper.
- Install the LED indicators inside the interior of your car. These ought to be put in a location where you can see them without taking your eyes from the road. For certain kits, placement suggestions for the indicators are included.
- Volume can be changed. Make sure the system is working properly by testing the volume. When it activates, you don’t want to be taken by surprise.
Contact a service center to have a professional handle the installation of your aftermarket blind spot monitor system if you have any inquiries or problems. A specialist can be required to take control because some systems have numerous processes and can be challenging to attempt.
How much does adding blind spot monitoring cost?
A reliable system should cost between $300 and $500. You might wish to install it yourself if you have a free Saturday. It is, however, a pretty drawn-out procedure. It will cost at least $200 to have a kit properly fitted.
Can a Camry have blind spot monitoring added to it?
The 2019 Camry XSE V6 model includes the Blind Spot Monitor (BSM) with Rear Cross-Traffic Alert (RCTA) as standard equipment, while the Camry LE model offers it as an optional package. There is a Blind Spot Monitor System that is even more sophisticated.
Can the RAV4 Le receive blind spot monitoring?
All Standard RAV4s and RAV4 Primes come with BSMs. However, you will need to add the BSM as part of an options package on the XLE or XSE trims if you want a hybrid RAV4. The RAV4 LE Hybrid does not have BSMs.
Toyota added blind-spot monitoring when?
One of the key factors in Toyota continually ranking among the top safety rankings from the Insurance Institute for Highway Safety is the Blind Spot Monitor (BSM), which has been available on some models since 2014.
Blind spot mirrors: Are they worth it?
A blind spot mirror is a practical device attached to a car’s side mirrors to indicate the driver areas of the road that are obscured from their field of view. You can essentially maintain track of the car that is behind you and change lanes without risking your safety.
Is there a blind spot monitor on the 2020 Toyota 4Runner?
A full complement of active safety features, such as automated emergency braking, adaptive cruise control, and blind-spot monitors, are now included as standard equipment on the 2020 Toyota 4Runner. That is sufficient for one point above average, but it is docked for the disappointing results of independent and federal crash tests. Our scale gives it a 4 out of 10.
Overall, the 4Runner received a four-star rating from the NHTSA, with four stars for frontal crashes, five stars for side-impact collisions, and three stars for calculated rollover evaluation.
The IIHS concurs. In several crash tests, the 4Runner received “Good ratings, but the “Marginal in the driver-side small-overlap test, which mimics impact with an item like an approaching car or a utility pole, is worrisome. The IIHS also gave the 4Runner’s headlights a “Poor” rating.
What is the price of installing BSM in a car?
- Under $250: Low-cost blind spot monitoring devices typically have fewer features and less precision. Most have a few sensors and simple indicators.
- The accuracy of the built-in sensors is improved by midrange blind spot monitoring systems, which cost $250 to $500, although most still fall short of the performance of OEM systems present on the majority of contemporary cars.
- $500 and up: This is the price range you should think about if you want the highest accuracy and dependability. Here, sensor accuracy is great, and internal controls frequently make use of cutting-edge algorithms to minimize false triggers.
Has the Toyota Corolla 2021 been equipped with blind-spot monitoring?
The 12th generation Corolla is back for a second year with upgraded safety features and a new Apex Edition. The Corolla Apex Edition improves the handling of the Corolla by adding new 18-inch wheels, bolder body modifications, and updated suspension improvements. Android AutoTM compatibility and two more airbags are now standard on all 2021 Corolla trim levels. Depending on the grade, a blind spot monitor with rear cross traffic alert is also included or available.