Where To Jack Up A Nissan Altima?

Registered

Since I’m new to vehicles, I’ll try to summarize the numerous discussion threads on when and how to utilize jack stands.

You should only use your scissors jack to change tires. According to the directions for the scissors jack, you should place them on the frame rail between the two notches. You cannot install your jack stands in the same frame rail location between the two notches if you elevate your automobile with a scissors jack. Unless you have special jack stand adapters (see below diagram) particularly built for the curvature of the frame rail, using jack stands on another area of the frame rail close to the notches may cause your frame rail to flex (see photos above).

A floor jack is required, which you can attach to the garage jack points or to the red positions in the aforementioned diagrams on the midline of the vehicle. After raising the vehicle, position your jack stands on the four frame rail regions located in-between the two notches.

In This Article...

How can I place four jack stands under my 2018 Nissan Altima?

I cannot place my jack stand underneath the pinch weld between the two notches when using my low-profile floor jack (which I bought to lift the front and rear ends of Mustangs and Tauruses) to lift my Altima at Location B.

I have no clearance to pump the jack, therefore I can only access Location B from behind the pinch weld or from the front of the vehicle.

My current plan of action is to

1. Lift the automobile using the scissor jack to access the tire,

2. Lift the vehicle with the floor jack in place beneath Location B and in front of the pinch weld.

3. Subsequent the pinch weld, place the jack stand.

1. Can I hoist the car, place the jack stand under Location B, and position the floor jack under the pinch weld (Location A)?

2. Should I exercise any caution utilizing this method, if I can?

1. When the Nissan Automotive Engineers opted against adding a second rear lift/jack stand point, were their heads up their asses?

2. Can I raise the car, set the jack stand beneath the pinch weld, and position my floor jack with the middle of its arm about 10″ in front of the read pinch weld?

3. Can someone offer advice on how to put the back end on jack stands?

Jack Stand Altima Nissan Points

To perform maintenance on a component, I need to crawl underneath my automobile. Because cars are heavy, it’s best to research and do this carefully because if you go under them and they fall on top of you, this could result in amputation or death. Going to a garage and having someone else do it is the easiest and safest option, but this is more expensive.

I’ll try to explain the several forum threads on how and where to utilize jack stands on a 2 gen Nissan Altima 1993-2001 because I’m new to vehicles. Although it appears straightforward, the large number of people who have started forum discussions indicates that there may be some uncertainty, so I thought I’d try to clear things up.

Update: Joe wrote in on September 16, 2010 to tell that he was unable to locate the jack stand adapters. Even though I looked, I was unable to locate them. Here are several studies:

Using hard wood, some people are building their own jack stand adapters. Choose a piece of wood that will fit your jack stands and carve a slot through the middle.
Harbor Freight sells two-piece rubber jack stand pads and 6 ton jack stands for $10 US each. Although not exactly as shown in the above diagram, they are affordable.
Many jack pads are available from Protech Products. The size is appropriate for your jack stands. $23US
According to flipper325 from this G35 forum topic, he is still producing the custom jack stand adapters for Harbour Freight jacks as of September 2010. A two-part polyurethane elastomer is used to cast them. $45US/pr

How is a 2008 Nissan Altima jacked up?

Find the jack kit, the jack handle, and the lug nut wrench.
Pre-Jack List: Actions to take prior to lifting a car.
Position Jack: Put the jack handle together and place the jack beneath the jack points.
Vehicle Lift: Carefully elevate the vehicle using the jack.

How do you use a floor jack to jack up a car?

Now is the moment to begin lifting your car if you have figured out the jack positions. It is important to stop and replace your jack if it feels shaky at any stage during this procedure rather than risk damaging your car or yourself.

Put the floor jack underneath the jack point of the car. The saddle of the jack should make as much even contact with the frame of the vehicle as feasible.

With the handle, start pumping the floor jack. Pump away until the saddle of the jack touches the frame of the car. Take a break, determine how the saddle is situated with respect to the car’s frame and the jack points, and then restart if necessary. If not, keep pushing until your car is at a working height.

How much should my automobile be jacked up?

A jack lift height of 20 inches is sufficient for the majority of autos. Unless, of course, you like lifted off-road vehicles with enormous tires, in which case you’ll need something with a bigger lifting capacity.

Is it possible to lift a car by the differential?

The phrases “certainly” and “probably” are very different since we are a maker of vehicle lifts and floor jacks, and we have seen just about everything there is to see go right and wrong in auto shops over the previous 50 years. This year, millions of people will jack up their cars by the differential, yet very few of them will ever cause damage to their car through carelessness or a faulty component. To some people out there, that might not mean much, but to us, it means everything. So here is our position on the subject: Unless the manufacturer specifically advises it, never jack up your car by the differential. It doesn’t matter what your neighbor thinks or what you observed the tire shop workers performing without a hitch while moving at breakneck pace.

We produce a variety of lifting equipment at BendPak, and we’ve seen what may happen when safety procedures aren’t followed. If you lift a truck on a two-post lift without employing frame cradle cushions, for example, you could find yourself on a one-way journey to Lawsuit City, population you. It only takes one instance of using the wrong lifting equipment. Always apply lifting force with a floor jack at the OEM-recommended positions, and then position your jack stands correctly, as close to the jacking point as you can. Additionally, always set up jack stands before working.

On an automobile, where are the lift points?

In order to safely lift the car, most automobiles have strengthened metal ribs that serve as the jacking points. There are typically four jacking points on each car. They are situated beneath the car’s rocker panels, close to the front wheels, and close to the back wheels.

A scissor car jack is what?

Vehicles are raised from the ground slowly and safely using scissor jacks. Because they are formed of diagonal metal parts that compress and extend similarly to a pair of scissors, they are known as scissor jacks.

How is an automobile suspension lifted?

Another option for boosting your vehicle’s ground clearance by about 2 or 3 inches is to buy a suspension lift kit. You will be better equipped to navigate bigger barriers and uneven roads because the bottom of the car will sit higher off the ground. Additionally, a suspension lift kit will enable you to mount bigger tires, which will increase the ground clearance of your car. Be sure to consider all of the advantages and disadvantages of lifting your car before deciding to do so. You should also take the time to learn about the local rules and laws in your area that pertain to vehicle lifts.

How long can an automobile be raised and lowered?

After employing a hydraulic lift or jack lift, a heavy object can be supported by a jack stand. In order to replace a wheel, change the oil, or inspect any other component underneath a car while working on it, you would use a jack stand. We have enquired as to the maximum amount of time a car can be supported by jack stands. Here is what they gave us.

A car can be left on jack stands for however long is necessary. For days, weeks, months, or even years, your car could be left on jack stands. As long as your car is jacked on a flat surface, everything will be OK. One thing to keep in mind is that it’s preferable to put your car on concrete rather than asphalt because asphalt is softer and your jack stands risk leaving a mark if left there for an extended period of time.

Since your tires will gradually lose air if you leave your car standing on its own and you run the risk of damaging your rim, leaving it on jack stands is a smart way to store your automobile. Additionally, check the vehicle’s security to ensure that even a small bump won’t cause it to overturn. Continue reading for more details about jack stands.

Let us first state that we hope you find the links provided here beneficial before you continue reading. We may receive a commission if you buy something after clicking on one of the links on this page, so thank you!

What three varieties of jacks are there?

Trolley jacks, bottle jacks, and scissor jacks are the three primary varieties of car jacks. Although they all carry out the same basic tasks slightly differently, some varieties are more stable than others (as we explain below)

What exactly are car lift points?

The Law of Gravity must be respected when using a vehicle lift. You achieve this by being aware of, using, and applying the proper lift points for the particular car in your bay.

The lift’s lift points enable it to balance the vehicle’s center of gravity while it is hung in the air with the proper adapters.

The majority of the time, vehicle lift falls are avoidable. It frequently boils down to utilizing the incorrect adapters, placing the car at the incorrect lift points, or failing to take the vehicle’s center of gravity into consideration (or not using the right adapters properly).

Depending on the vehicle being lifted, there are many vehicle lift points. Finding and using the proper lifting points is essential because the center of gravity is not always in the center. You can find lift point information online, by car manufacturer, or by measuring your own center of gravity.

The imbalance could overload the arms and cause the vehicle to slide off its mounting if the lift pads are not placed at the proper lifting locations.

Life-threatening errors might result from skipping stages, “eyeballing it,” or utilizing your expertise and intuition in place of explicit measurement instructions. Every time, gravity’s rule prevails.