The airbag light connects the seat belt system and the airbag system as part of the Supplement Restraint System (SRS) in automobiles. When you turn on your automobile, the airbag light comes on for around seven seconds before going out, signifying that the internal system check was successful and finished. When the airbag light either never turns on or stays on while blinking, an issue exists. The airbag light needs to be reset at this stage.
Examining seat belt components, fixing bad clock springs, and replacing faulty sensors are a few techniques for turning off an airbag light. New bulbs or a fully charged battery are other options. While most repairs can be done without a professional, others may.
The following 10 steps will reset your airbag light:
- Turn on and off your ignition.
- Test drive your car when it has been restarted.
- Check the airbag switch for the passenger.
- Check to see if the seat belts are in place and functioning properly.
- Check to see if the passenger seat sensor is off.
- Use a scanner with the ability to reset the SRS or airbag light.
- Fix the broken airbag sensors.
- Replace or repair a broken clock spring.
- Check to see if the airbag is working properly.
- seek for a specialist’s help.
Although not exhaustive, the list above includes tried-and-true methods for tackling the problem. Some of them might not apply to your vehicle because compatibility is always based on the year, make, and model. It is recommended that you have your service manual on hand when carrying out any of these fixes. Always follow the manufacturer’s recommendations, too. Let’s get started on resetting your airbag light right away.
In This Article...
Is a reset of the airbag light necessary?
The airbag warning light could come on as a result of a sensor malfunction or accidental travel. It will be necessary to reset the system and examine the sensors. The purpose of the airbag clock spring is to provide continuity between the vehicle’s electrical wiring and the driver-side airbag.
The airbag light stays on for what reason?
A problem with the seatbelts or airbags is indicated by the airbag light. Therefore, it’s usually not a good idea to drive when the airbag light is on. We advise having it towed to the dealership rather than driving it yourself if it continues to flash inside your car.
What does it cost to repair the airbag light?
The first step is to reset the airbag light, which can take several hours and cost a few hundred dollars on average, however it can cost as much as $600 depending on the automobile.
Driving with the airbag light on is it forbidden?
In some vehicles, it is even possible to turn off the passenger airbags, which will make your dashboard’s airbag light come on.
You should only deactivate the passenger airbag when absolutely necessary because, as was previously said, airbags are an essential safety element.
If your airbag light ever illuminates for no apparent reason, you should try to resolve the situation.
By removing the battery, is it possible to restart the airbag light?
Without a scanner, most automobile models make it difficult to reset the airbag light. This is a safety warning since, when the airbag light appeared, you should always fix the problem. Fortunately, if you fix the issue, the airbag light will typically also turn off by itself in many automobile models.
However, in some older vehicles, the airbag light can be reset without a scanner by disconnecting the battery wires.
Make that there are no loose wires or rust in the connector plugs in the wiring system under the driver’s or passenger’s seat. Restart your car after spraying an electronic cleaner on the connecting plugs.
If you can’t detect any issues there, you should really invest in an OBD2 scanner or have a shop interpret the codes because otherwise you’ll have to guess what the issue is.
How is a Nissan airbag code read?
To read the codes, count the flashes the light makes, then count them again after the pause. For instance, two flashes, a pause, and four flashes indicate a code 24 issue with your airbag system. Codes 12 and 13 indicate low battery voltage and a shorted or grounded airbag circuit, respectively.
Where is the switch for the passenger airbag?
If the vehicle has a switch called the Passenger Airbag Cut Off Switch, it can be used to deactivate the passenger airbag.
When the passenger door is open, you may access the switch for the passenger airbag on the passenger side of the instrument panel.
ALL FRONT-FACING PASSENGERS (CHILDREN AND ADULTS) CAN SIT SAFELY ON THE PASSENGER SEAT WHEN THE AIRBAG IS ACTIVATED.
Rear-facing child seats are safe for use on the passenger seat when the airbag is switched to OFF.
Can a blown fuse turn on the airbag light?
The car could have blown a fuse, for example. There are other fuses that could be to blame, but fuse #13 is most likely the one. You probably need to change fuse #13 and perhaps other fuses if your airbag light is on and your rear windshield wiper is not working. The airbag light can undoubtedly turn on as a result of blown fuses.
The airbag light may also abruptly turn on in a number of other situations. A mechanic or auto parts store should be able to decipher the code that the airbag system emits when it is acting up, which will give them a hint as to what specific issue the airbag is experiencing. There are numerous potential issues with the airbag because it is a complicated system of sensors, wiring, and programming that must suddenly activate during an accident after lying dormant for years. Check the fuse box to see whether you have a blown fuse first, but if not, you’ll likely need to take it to the dealer or a qualified mechanic for service.
Does the airbag fuse exist?
Your car’s airbag most likely has a fuse, however the fuse does not turn on the air bags. Your complete system will also be inoperable if your service airbag lights are on.
How do I deactivate my airbag?
If the vehicle has a switch called the Passenger Airbag Cut Off Switch, it can be used to deactivate the passenger airbag. When the passenger door is open, you may access the switch for the passenger airbag on the passenger side of the instrument panel. Verify that the switch is set to the appropriate position.
Do airbag sensors cost a lot?
Depending on the automobile model and labor charges, the cost to replace an airbag sensor ranges from $100 to $600. A sensor for an airbag costs between $50 and $300, as does the labor.
Both the airbag sensor and its replacement are delicate parts. Even for an expert, correctly diagnosing and installing the airbag sensor can take up to two hours.
The airbag sensor itself is typically not very expensive; you may anticipate paying between $50 and $300 for a brand-new one. Never purchase aftermarket sensors; don’t take the chance. Always purchase OEM original, authentic items.
You can save money by replacing the airbag sensor yourself if you are highly confident working on cars and meticulously following the repair manual.
If you have even the least qualms regarding the replacement, have a pro handle it.
Keep in mind that it is a crucial component, therefore installing it properly is important in case of an accident. Additionally, if you make a mistake, there is a chance that all of the airbags in the car will deploy, which will cost thousands of dollars to fix.
Are new airbag sensors required?
Any crash sensor that might have been damaged in some way by an accident needs to be replaced. The airbags will definitely need to be replaced if they were deployed during an accident.