Nowadays, a remote keyless entry device is standard on all new Nissan vehicles. With this method, you can start your car’s engine and unlock your door without really using a key. It’s convenient to have a Smart Key as Nissan does, but what happens if the battery dies? It can be difficult to choose the micro-battery size to buy for your Nissan intelligent key because there are so many different sizes available. Fortunately, we’ve looked into batteries and the replacement procedure to give you an answer here.
The CR2032 3-Volt battery is the same size for all Nissan Smart Keys. Use these instructions to replace the battery in your key fob:
- Press the tiny button on the rear of the fob to remove the valet key.
- Gently pry open the fob with a screwdriver or card until it clicks and separates into two halves.
- Replace the battery after removing the old one.
- Replace the valet key and put the key fob back together.
Here is a summary of Nissan Smart Key battery sizes and how to change them. However, there is more to understand about this procedure. We will go into more depth on how to change the battery in the following sections of this essay. We’ll also go over programming the Nissan key fob, how long the batteries should last, and whether or not they’re covered by a warranty.
Let us first state that we hope you find the links provided here beneficial before you continue reading. We may receive a commission if you buy something after clicking on one of the links on this page, so thank you!
In This Article...
How can I program my Nissan key fob now that the battery has been changed?
First, turn off the ignition and sit inside your car with the doors closed. Next, for around 15 seconds, push and hold the lock and unlock buttons on your key fob.
Next, press and hold the lock button for one second before releasing it and pressing the unlock button for the same amount of time. Finally, start your car and check your key fob to make sure it’s functioning properly.
How much does a Nissan key fob battery change cost?
Although replacing the key fob battery on your Nissan model is a simple procedure, it does require handling delicate and sensitive electronics. Make sure to use gloves to prevent harm to the key fob. The CR2032 3V battery is used in the Nissan key fob. Typically, a multipack of them costs less than $5 USD. A tiny flathead screwdriver is also required.
- Find the open slot between the front and rear portions of the key fob on its top.
- Nissan key fob flipped over to the rear
- Slide the little lever to release the emergency key.
- Delete the emergency key
Can my Nissan be started without a key fob?
However, if the Nissan key fob battery alone needs to be replaced, your Nissan might still start even with a dead key fob battery: Put the key fob in the port if your Nissan car, truck, or SUV has one, then push the START/STOP button while tapping the clutch or brake pedal.
How long does the battery in a key fob last?
The battery in your car’s fob or remote will eventually need to be replaced, just like any other battery. A car fob battery should typically last three to four years. In addition, there are several indicators that will let you know when your fob battery is running low.
Signal strength loss is the initial symptom. The majority of contemporary fobs can communicate with your car up to 50 feet away. But as your battery ages, the signal’s intensity and range will decline. Another indication that your key fob battery needs to be changed is that you are having to push buttons to lock and unlock doors repeatedly.
Does the key fob need to be reset after a battery change?
Your remote key fob needs to be attached to a receiver in the car in order for it to function properly. You may need to reset the fob after changing the battery since occasionally this can break the paired connection between the key and the vehicle.
Should a Nissan key fob be reconfigured after a battery replacement?
In conclusion, after changing your battery, you do not need to reset your keychain. However, you might need to reprogramme your fob if it still malfunctions after the battery has been changed.
-You will need to re-program your key fob to your automobile after changing the battery in it.
What should I do if the battery in my Nissan key is low?
You can resume using the key fob to start and enter your car once the battery in your Nissan smart key is replaced. The steps to follow to change the battery in your key fob are as follows:
- When the battery died, you could still enter your Nissan by using the concealed key.
- Remove the old battery and the key casing.
- Place the negative side of the CR2025 battery upward before replacing it.
- Reassemble the key fob and give it a try!
What occurs if the key fob dies while you’re driving?
This issue has been foreseen by automakers ever since the key fob was created. Nothing will happen if your key fob dies while you’re driving. Simply because the key fob is a locking and starting device only, the automobile will continue to run. The key fob has no influence over the ignition or engine once the automobile is moving.
Even though you’ll need to go to a general store or pharmacy to get the battery, replacing the battery in your key fob simply takes a few minutes if you’re pressed for time.
Why not take the time to renew your auto insurance at the same time as you’re replacing the batteries in your key fob?
You can access a new quotation with just a few taps on your phone screen by downloading the Jerry app and answering a few questions.
Jerry assists you in finding and comparing rates from more than 50 leading suppliers in minutes as a licensed broker. Jerry can assist you with purchasing new insurance and even canceling your existing policy when you find a lower rate.
Will a dead key fob deplete the battery in my car?
We frequently receive inquiries like these at the shop. Yes, it is the correct response. Your key fob can eventually deplete your battery if you keep it in your car when it is not in use. Even when not in use, the key fob continuously transmits a signal to the vehicle, which consumes a tiny amount of electricity. So, if you keep your key fob in your car for a long time, the battery will ultimately die. If you find yourself in this predicament, you might try using a jumper wire or a portable battery pack to jump start your automobile.
Additionally, it may not be a good idea to leave your key fob in your car overnight or even just hanging nearby. The key fob may speak with your automobile if it is too close, which could drain the battery.
Are key fobs replaced by AutoZone?
AutoZone does offer key duplication services for cars made by Toyota, Ford, Honda, Dodge, GMC, Mercedes, Kia, and other manufacturers. These services include key duplication, transponder keys, key fobs, and vehicle key blanks.
DIY Key Fob Programming
You might be able to program a replacement yourself, depending on the make and type of your vehicle.
The steps for programming a key fob yourself can differ: Owner’s manuals from certain automakers include instructions. In many circumstances, information can be available online. The problem is that in order to complete the process quickly or at all, you might require two functional key fobs.
Therefore, it is wise to acquire and set up an extra remote before you require it. Additionally, it’s a wise move because most used-vehicle buyers, particularly auto dealers, would pay extra for a car that has at least two functional sets of keys or key fobs. Therefore, having a spare key will not only be useful when you need it, but it will also benefit you in the long run.
After-Market Key Fobs
You may be able to buy an after-market key fob via a locksmith or online if your automobile is more than five years old. These sorts of fobs range in quality, but they are less expensive than other options.
Locksmith
If you have the option of receiving your replacement key from a locksmith or the dealership, the latter may be less expensive. Before making a choice, be sure to inquire about prices with your nearby vehicle dealership.
Can a key fob be programmed without visiting the dealership?
The programming process is detailed in the owner’s manual for the vehicle, but the vehicle must be present, he added. Be advised that most customer-programmable key fobs, regardless of brand, require two active, functional keys in order to program a third new key without visiting the dealer, according to Yu.
Why doesn’t my automobile recognize my key fob?
The most frequent cause of a keyless entry system failing to send signals is a faulty battery in the key fob. Use the extra key fob to unlock the car and turn on the ignition if one is available.
Use the key that is included in the spare fob if it is not available to unlock the door. Check your owner’s manual for information on how to start your automobile when the key fob malfunctions.